Citizen CAL B742 Manual

Citizen Ur CAL B742

Læs gratis den danske manual til Citizen CAL B742 (1 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Citizen CAL B742, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

112

Crown

MODELS – BJ * ECO-DrIvE aQUaLanD2**

Mvmt. Cal. No. B74* Level of

Stored Energy

Lower

Right

Button (A)

Upper

Right

Button (B)

‘Real Time’ Second Hand

Function

Hand

24 Hour

Hand

Mode Hand

Date

FEATURES

Light Powered

Depth Sensor

Depth Indicator Hand

Elapsed-Time Bezel

Water Sensor

50 Minute Chronograph

Water-Resistant to 200 Meters

Reserve Power Indicator

Rechargeable Battery

BENEFITS

Free Energy Source

Accurate Depth Indication

Instant Depth Reading

Assists in Measuring ‘Down Time’

Automatically Switches to Dive Mode

Precise Measurement of Elapsed-Time

Good for Scuba Diving

Safe Dives

No Battery Changes

IMPORTANT NOTE: Before use, be sure the watch is

fully charged. The charge level of the energy cell can be

checked by placing the watch in time mode. The function

hand (sweep second hand) will move to one of three

positions indicating the level of stored energy. Level

2 indicates a maximum charge*. Level 1 indicates the

charge level is in normal operating range. NG indicates

the charge level is not sufficient for diving and is getting

low for normal operation. For recharge times and rates,

refer to your instruction manual or visit our website at

www.citizenwatch.com. Do not use a halogen light, or

place the watch on the dashboard of a car for charging as

temperatures in excess of 140 degrees Fahrenheit can be

reached which may damage vital components of the watch.

If either a low charge/no charge state is reached, or the

function hand continues to indicate ‘over-zone’, or

another malfunction is experienced, then an ALL RESET

AND 0-POSITIONING PROCEDURES will be required.

ALL RESET AND 0-POSITIONING PROCEDURES

Unscrew the crown to release it from the case and pull

it out two ‘clicks’. Simultaneously push the upper right

(B) and the lower right (A) buttons at the same time and

hold down for 2-3 seconds, then release. This ‘resets’ the

movement.

Press the upper right button (B) to set the function

and mode hands to the 0 or 12:00 position.

Set the time if necessary.

Return the crown to its position next to the case and

screw it in to secure it.

Note: After the ALL RESET, the function hand will

indicate ‘NG’ charge for approximately one hour, then will

return to the correct charge indication.

TO CHANGE MODES

To switch to the chronograph mode while in normal

time display mode, (mode hand on DV), press and hold

down the lower right button (A) for 3 seconds. Mode and

function hands will move to 0-position.

To switch back to normal time display mode from

chronograph mode, press and hold the lower right button

(A) for 3 seconds.

Watch switches to dive standby mode automatically when

sensor is wet.

To switch back to time after dive, press and hold the

upper right button (B) for 3 seconds.

To call up maximum depth memory of the last dive,

while in the time or dive mode, press the upper right

button (B). The depth indicator hand (mode hand) will

move to show the deepest point of the last dive. Press and

release the upper right button (B) again to return the depth

indicator hand (mode hand) back to its previous position.

TO SET THE TIME

Unscrew the crown by turning it in a counter clockwise

direction to release it.

Pull the crown out two ‘clicks’ to set the Hour and

Minute hands. Turn the crown to move the hands forward

to the correct time while observing the 24 Hour hands so

as to properly set the time for a.m. or p.m.

Push the crown in to finalize setting.

TO SET THE DATE

After the correct time has been set (24 Hour hand

indicating whether time is a.m. or p.m.) and the crown is

pulled out one ‘click’ (intermediate position), then rotate

the crown in the counterclockwise direction to set the date.

Once time and/or date is set, then push the crown in

against the case and while continuing to apply pressure,

turn the crown clockwise until it is screwed tightly

against the case.

TO USE THE CHRONOGRAPH

Hold the lower right button (A) down for 3 seconds

while in normal time display mode to switch to

chrono graph mode. Function hand now becomes

chrono graph sweep second hand and mode indicator

becomes minute register hand. Small second hand

always shows actual running seconds.

Press and release the upper right button (B) to start or

stop chronograph.

When stopped, press the lower right button (A) to

reset hands to 0-position. If either of the two hands does

not return to the 0-position, please refer to the ALL

RESET PROCEDURE outlined previously.

To return to normal time display mode from chrono -

graph mode, press and hold the lower right button (A).

Chronograph does not operate simultaneously with time

or dive mode. If mode is switched from chronograph,

chronograph data is deleted.

TO USE THE DEPTH METER

Before the watch goes into dive standby mode and before

diving, make sure ‘screw lock’ crown is tightened securely

against the case. Watch is now ready for diving.

Watch will automatically switch to dive standby mode

from either normal time or chronograph mode whenever

water sensor gets wet. Mode hand moves to ‘DV’ and

depth indicator hand will move to ‘0’ feet. (If this does

not happen, please refer to the ALL RESET PROCEDURE

outlined previously).

To read the maximum depth memo for the last dive

(after all moisture has been removed from exterior of

watch) press the upper right button (B) while in time or

dive mode. Depth indicator hand will point to the

maximum depth of your last dive.

Press the upper right button (B) again to return to the

previous mode.

Depth meter and chronograph cannot be used

simultaneously. The elapsed time indicator (ETI) bezel

ring should be used to keep track of elapsed dive time

(see your instruction manual for detailed information).

Maximum depth measurement is 125 feet. If diver exceeds

that depth, depth indicator hand rests on ‘over-zone’ mark

until returning to 125 feet or less.

Always use the ‘buddy system’ when diving. This

watch is not a substitute for a dive partner.

It is recommended that there be no diving unless the

power level indicator is at Level 1 or 2.

*Level 2 indicates maximum charge level and will remain

there for 3-8 hours depending on the type of light used

for charging and functions of the watch being utilized.

For charge rates and additional in depth instructions,

please refer to the full instruction manual or our website

at www.citizenwatch.com.

Produkt Specifikationer

Mærke:	Citizen
Kategori:	Ur
Model:	CAL B742

Har du brug for hjælp?

Hvis du har brug for hjælp til Citizen CAL B742 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ur Citizen Manualer

Citizen Marvel Deadpool CA0688-04W Manual

28 Juli 2025

Citizen Disney Aurora Diamond EM0594-53W Manual

28 Juli 2025

Citizen Axiom EM0633-53A Manual

27 Juli 2025

Citizen Star Wars Darth Vader Tsuno AN3669-52E Manual

27 Juli 2025

Citizen Eco-Drive Brycen AW1598-70X Manual

27 Juli 2025

Citizen Star Wars Jedi Master BM7498-00W Manual

27 Juli 2025

Citizen Ladies' Dress EM0850-80D Manual

27 Juli 2025

Citizen Disney Princess Ariel GA1073-63W Manual

27 Juli 2025

Citizen Star Wars R2-D2 Tsuno AN3666-51A Manual

27 Juli 2025

Citizen Silhouette Chronograph FB1443-08A Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Casio G-Shock GA-700UC-3A Manual

28 Juli 2025

Casio Baby-G BSA-B100 Manual

27 Juli 2025

Casio G-Shock GM-110 Manual

27 Juli 2025

Casio G-Shock GM-S5600 Manual

27 Juli 2025

Casio Edifice EF-527D-1A Manual

27 Juli 2025

Casio Edifice EFR-571 Manual

27 Juli 2025

Casio G-Shock GST-S110 Manual

27 Juli 2025

Casio Baby-G BGD-570 Manual

27 Juli 2025

Casio Edifice EFS-S510 Manual

27 Juli 2025

Casio Vintage A100WE-1AVT Manual

27 Juli 2025