Comar AIS-2-USB Manual

Comar Ikke kategoriseret AIS-2-USB

Læs gratis den danske manual til Comar AIS-2-USB (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Comar AIS-2-USB, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation:
The AIS-2-USB Receiver is not waterproof and should be
mounted in a dry location. The unit can be fixed by the 4
mounting holes in the end flanges.
It will require connection to a marine VHF antenna via the
BNC socket at the rear or with a BNC to VHF adaptor socket.
Connect the Receiver to your computer via the supplied USB
cable. Switch on the computer and load the Drivers as
detailed on the CD. This will create a Virtual Com Port that
will enable the AIS data sent via USB to be displayed on
a compatible AIS computer program.
The output Baud rate is set to 38,400, if you wish to change
this to 4800 baud, disconnect the power, unscrew the two
screws to release the front cover and move the jumper
located in the middle to the 4800 position.
Operation:
On applying power the Green LED will light and the two
Channel Red LEDs will come on continuously for
approximately 10 seconds then extinguish. If you are within
range of vessels transmitting AIS data the two channels Red
LEDs will flash intermittently indicating reception of a AIS
messages which will be sent as NMEA data via the USB
connection to the computer.
Limited Warranty:
Comar Systems Ltd warrants this product to be free from
defects in materials and manufacture for one year from the date
of purchase. Comar Systems Ltd will, at its sole option, repair or
replace any components that fail in normal use. Such repairs or
replacement will be made at no charge to the customer for parts
and labour. The customer is, however, responsible for any
transportation costs incurred in returning the unit to Comar
Systems Ltd.
This warranty does not cover failures due to abuse, misuse,
accident or unauthorized alteration or repairs.
The above does not effect the statutory rights of the consumer.
Note: Every effort has been made to ensure that all information
contained in this manual is accurate at the time of going to
press. However AIS is a new technology and the legislation is
subject to change. We therefore cannot take any responsibility
for the content of this manual and advise that you take normal
steps to ensure that the information is at its most current when
you are reading this manual.
Product Support
Comar Systems Limited
Unit 7, Medina Court
Arctic Road
Cowes
Isle of Wight, PO31 7XD
United Kingdom
Telephone: +44 (0) 1983 282400 Fax: +44 (0)1983 280402
E-mail: techsupport@comarsystems.com
Internet: www.comarsystems.com
www.busse-yachtshop.de | info@busse-yachtshop.de
Fault finding:
No power light is displayed
● Check that the computer is on and the USB cable is connected
Channel A and Channel B lights do not flash
● Check that a VHF antenna is fitted and correctly connected.
● Check that the antenna is correctly positioned – i.e. at a suitable
location to visibly ‘see’ vessels.
Channel A and Channel B lights flash but no data is received
If the red channel lights flash then data is being received from
nearby vessels.
● Check on the PC application or device that the correct port is
assigned and the correct baud rate is setup. The correct baud rate
is 38400.
I can receive ships on my display but no names are shown.
● Remember that the names of ships as well as other static
information is only sent every 6 minutes or when requested by
another station.
Specification:
Dimensions Overall: 120 x 86 x 37
Power: via USB
Current: 130mA
Output: Via USB NMEA 0183
Message type: VDM
Baud Rate: 38400 (4800 by internal link)
Receiver: Dual Channel Parallel
Frequency: 161.975 and 162.025MHz
Sensitivity: -112dBm
Connections: USB2.0 type B
Cable: 1m type A to type B
Antenna: BNC 50 Ohm
Installation
and
Quick Reference Guide
AIS-2-USB
Receiver
www.busse-yachtshop.de | info@busse-yachtshop.de

Produkt Specifikationer

Mærke: Comar
Kategori: Ikke kategoriseret
Model: AIS-2-USB

Har du brug for hjælp?

Hvis du har brug for hjælp til Comar AIS-2-USB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Comar Manualer

Comar

Comar AIS-2-USB Manual

31 August 2024
Comar

Comar AIS-2-NMEA Manual

31 August 2024
Comar

Comar CSB200 Manual

31 August 2024
Comar

Comar ASR 100 Manual

31 August 2024
Comar

Comar CSA-300 Manual

31 August 2024
Comar

Comar AST-200 Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo

Festo EMME-AS-80-M-LS-AMB Manual

30 Juli 2025
Tiptop Audio

Tiptop Audio Octogain Manual

30 Juli 2025
Artec

Artec SE-ADL Manual

30 Juli 2025
Intermatic

Intermatic WH40 Manual

30 Juli 2025
Deye

Deye SUN-M160G4-EU-Q0-I Manual

30 Juli 2025
Festo

Festo EMMB-AS-60-02-S30SB Manual

30 Juli 2025
Festo

Festo VPPM-6F-L-1-F-0L6H-V1P-C1 Manual

30 Juli 2025
Intermatic

Intermatic R8806P101C Manual

30 Juli 2025
CSL

CSL 300735 Manual

30 Juli 2025
Advantech

Advantech PCM-27D24DI Manual

30 Juli 2025