Compustar KP2 Manual

Compustar Fjernbetjening KP2

Læs gratis den danske manual til Compustar KP2 (2 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Compustar KP2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
engine back OFF, close the driver’s side door, and re-attempt steps
#1 through #5.
Via DroneMobile App
If your KP-2 touchpad module is installed with a Drone KL1 KeyLocker
system, you can now manage your passcode(s) from the DroneMobile
App. Please visit https://help.dronemobile.com and search “KP2”.
KP-2 User Guide (Arming + Disarming)
Arm/Lock - To arm and lock your vehicle’s doors, hold down
the LOCK button for 2.5 seconds - do not press any number.
One chirp/honk and One parking light flash will confirming
lock/arm.
Disarm/Unlock - To disarm and unlock your vehicle’s doors,
hold down the LOCK button for 2.5 seconds, then enter your
passcode. NOTE: please press each digit firmly and pause for 1
seconds for two chirps/honks and two parking light flashes,
confirming unlock.
Compatibility (ENGLISH)
CM-X, CM7 Series, and CM-DC3 (Make sure firmware is updated)
Connect to the controller RPS port (white 4-pin).
ȗ-X: ature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity. Fe
ȗǚǽFeature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity.
ȗǚǖǓǓǽFeature Option 3-16 to Setting 2 (KP2).
ȗȐǖǽ$($ted Operation
ȐǜǓǓǼȐǜǓǓǼ)ǕǗǓǓșke sure firmware is updated)
Connect to the controller UART port (gray 4-pin), using ‘ANT-Adapt-
er-KP2’ (included in kit).
ȗǜǓǓ/AS: ature Option 4-11 to Setting 3 (KP2), 4-15 for Fe
sensitivity.
ȗǕǗǓǓǽ +/$*)ǖȐǓǔ //$)"ǕșǕȚǼǖȐǓǖFeatur to Se for
sensitivity.
Mounting & Installation
1) The KP2 touchpad module should be mounted on the front
windshield on the interior, driver’s side. Thoroughly clean and dry the
intended surface.
2) Connect the 4-pin harness prior to mounting.
3) Remove the protective film on the KP2 touchpad module, exposing
the adhesive.
4) Firmly adhere the KP2 touchpad module to the interior of the
windshield at your desired placement. Hold the module in place for
ǖǓ. conds.
KP2 Programming and Passcode Reset
Via Touchpad Module
1) Using your vehicle’s key, turn the ignition to the ON position. You do
not need to start the engine. Then, open the driver’s side door and
leave it open.
2) Press and hold the LOCK button the KP2 touchpad module for 2.5
seconds.
3) If your system has a siren, it will lightly chirp and the red LED will
blink, indicating programming mode.
4) Firmly tap in the first digit of your new passcode. The LED will blink
green when input is received, and then red (with siren chirp) when it
is safe to enter the next digit. Repeat this process until you have
entered all 4/6 digits.
5) Once you have entered all of the digits, please wait until you hear
another siren chirp and see a single parking light flash. This indicates
that programming was complete and successful.
a) If programming is incomplete and/or fails, you will receive three
siren chirps and three parking light flashes. If this occurs, turn your
Compatibilité (FRANÇAIS)
CM-X, CM7 Series, et CM-DC3 (assurez ous que le micrologiciel est mis à -v
jour)
Connecter au port RPS du contrôleur (blanc à quatre broches).
ȗ-X : Option de fonction 3-16 au glage 2 (KP2), 4-15 pour la ré
sensibilité.
ȗǚǽ+/$*) fonction 3-16 au glage 2 (KP2), 4-15 pour la ré
sensibilité.
ȗǚǖǓǓǽ+/$*)fonction 3-16 au glage 2 (KP2).ré
ȗȐǖǽFonctionnement limité
ȐǜǓǓǼȐǜǓǓǼ /ǕǗǓǓș..0e rez-vous que le micrologiciel est mis
à jour)
Connectez ous au port UART du contrôleur (gris à quatre broches), en -v
utilisant 'ANT-Adapter-KP2' (inclus dans le trousse).
ȗǜǓǓ/AS : Option de fonction 4-11 au glage 3 (KP2), 4-15 ré
pour la sensibilité.
ȗǕǗǓǓǽ+/$*) *)/$*)ǖȐǓǔ0 ǕșǕȚǼǖȐǓǖ+*0-'f réglag
sensibilité.
Montage et installation
1) Le module du pavé tactile KP-2 doit être monté sur le pare-brise
Programming &
Operation Manual
CM-900
CM-900AS
CM2400
CM-X
CM7 Series
CM-DC3
White
Gray
(ANT-Adapter-KP2)
Red LED
Green LED

Produkt Specifikationer

Mærke: Compustar
Kategori: Fjernbetjening
Model: KP2

Har du brug for hjælp?

Hvis du har brug for hjælp til Compustar KP2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Fjernbetjening Compustar Manualer

Compustar

Compustar KP2 Manual

27 Juni 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

KICKY RIDE

KICKY RIDE KR-RS-FL8 Manual

3 December 2025
Vivanco

Vivanco UR 12 N Manual

14 November 2025
Danfoss

Danfoss MPCAN Manual

10 November 2025
Vivanco

Vivanco RC-21966 Manual

9 November 2025
SmallRig

SmallRig Wireless Remote Controller 3902 Manual

3 November 2025
Abus

Abus Comfion FUBE80000 Manual

31 Oktober 2025
Abus

Abus Smartvest Pro FUBE45010 Manual

30 Oktober 2025
Philips

Philips SRU3030/10 Manual

28 Oktober 2025
Rotel

Rotel RKP-200 Manual

15 Oktober 2025
One For All

One For All URC 4916 Manual

8 Oktober 2025