Corsair Commander Mini Manual

Corsair Ikke kategoriseret Commander Mini

Læs gratis den danske manual til Corsair Commander Mini (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Corsair Commander Mini, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

corsair.com/link

Introduction

The Corsair Commander Mini replaces manual

controls for fans and lighting with an software

interface, while simultaneously oering more

advanced control and expansion options than

motherboard BIOS settings. The Corsair Commander

Mini can be used as the hub of your Corsair Link

system allowing connections from other Corsair Link

enabled hardware. This guide will help you install

your Corsair Commander Mini.

Speciﬁcations

Package Contents

1 x Corsair Commander Mini unit

1 x Corsair Link Digital connection cable

3 x Fan extension cables

4 x Thermistor cables

1 x Mounting Tape

Cable Dimensions

Permanently attached cables

1. USB cable (24")

2. SATA power cable (18")

Expansion cables

1. Corsair Link Digital cable (18")

2. Fan extension cables (12")

3. Thermistor cables (24")

Electrical Speciﬁcations

Commander Mini Quick Start Guide

Electrical Speciﬁcations

Power Supply Voltage Input 11.4 - 12.6 volts

1 amp

2 amps

4 amps

Maximum Power

per fan header

Maximum power for

RGB LED channel

Maximum power for all 6 fan

headers and RGB LED channel

58.9

13.5

145 mm

Unit Dimensions

C D

corsair.com/link

Installation Instructions

1. Power o your system for the installation of the

Corsair Commander Mini.

2. The Corsair Commander Mini can be mounted in many

empty locations inside your case for ease of cable

routing. Its slim design allows for installation on the

rear of the motherboard tray in most cases. Its width

also allows for internal mounting in the optical disk

drive cage of most cases. We recommend making all

of the required connections ﬁrst, and then attaching

the Commander Mini to your PC case. Use the

provided mounting tape to secure the Commander

Mini unit to your PC case.

3. Connect the attached USB cable to any available

internal USB 2.0 header on your PC’s motherboard

(Refer to your motherboards manual for location).

Take care when connecting the USB cable, as it is

keyed to prevent incorrect installation.

4. Connect the attached SATA power connector to any

available SATA connector from your power supply.

5. The Corsair Commander Mini has 4 Corsair Link

Digital ports that are for connecting to other Corsair

Link Digital hardware. Use the provided Corsair Link

Digital cable to connect to an H80i or H100i. To

connect to a Corsair PSU with Corsair Link Digital

capabilities (I Series) use the cable supplied with the

power supply to connect to the ports on the

Commander Mini.

6. Connect the thermal sensors to the two-pin

headers labeled “Temp 1-4” on the Commander Mini.

Tips for connecting thermal sensors

The thermal sensors are designed to measure ambient

temperatures, so for the most accurate results, they

should not directly touch components. You may ﬁnd it

useful to mount the thermal sensors near air intake and

exhaust points, and if your PC case has multiple

compartments, you can try placing each of the sensors

in its own compartment. Since the thermal sensors can

easily repositioned, you can try various locations and

use what works best for you.

7. Connect any fans you wish to control to the four

pin headers labeled “Fans 1-6”. The included fan

extension cables can be used if necessary.

8. Connect the RGB LED strips (sold separately) to the

connectors labeled “LED 1”.

9. Hardware installation is complete.

10. Download the Corsair Link Dashboard software

11. The software can be downloaded from the following

location: www.corsair.com/linksw

12. Install the Corsair Link Software

The LED on the Corsair Commander Mini shows activity and

status. Green indicates USB connectivity with the host PC.

Amber (intermittent) indicates USB activity. Red indicates

USB connectivity error.

[Optional]

Produkt Specifikationer

Mærke:	Corsair
Kategori:	Ikke kategoriseret
Model:	Commander Mini

Har du brug for hjælp?

Hvis du har brug for hjælp til Corsair Commander Mini stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Corsair Manualer

Corsair XTM50 Manual

27 Juli 2025

Corsair Carbide Series 200R Manual

8 Juli 2025

Corsair iCUE 5000X RGB QL Edition Manual

8 Juli 2025

Corsair Carbide Series 175R RGB Manual

8 Juli 2025

Corsair Carbide Series 275Q Manual

4 Juli 2025

Corsair Carbide Series Air 540 Manual

30 Juni 2025

Corsair Crystal Series 460X Manual

30 Juni 2025

Corsair Carbide Series SPEC-06 Manual

30 Juni 2025

Corsair Carbide Series 678C Manual

30 Juni 2025

Corsair Carbide Series SPEC-04 Manual

29 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

VIZIO SmartCast M75-E1 Manual

27 August 2025

Prince Castle 740-T4 Manual

27 August 2025

ENTES EMR-53SL Manual

27 August 2025

Minix RIC SJ64-8 Manual

27 August 2025

Milwaukee M18 3019-21PS Manual

27 August 2025

ENTES RGI-12W Manual

27 August 2025

Crestron IV-SAM-VX2-S Manual

27 August 2025

SABO BC-250 PRO Manual

27 August 2025

ENTES DCA-11C Manual

27 August 2025

Russell Hobbs Desire 27140-56 Manual

27 August 2025