Cotech EMP200S-1 Manual

Cotech Strømafbryder EMP200S-1

Læs gratis den danske manual til Cotech EMP200S-1 (5 sider) i kategorien Strømafbryder. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Cotech EMP200S-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

UNITED KINGDOM • CUSTOMER SERVICE

tel 020 8247 9300 customerservice@clasohlson.co.uk www.clasohlson.co.uk 10 – 13 Market Place, Kingston upon Thames, Surrey, KT1 1JZe-mail internet postal

Ver. 20180924

Residual Current Device

with No-Volt Release Switch

Art.no 18-2032 Model EMP200-UK

32-3492 EMP200S-1

Please read theentire instruction manual before use and save it for

future reference. Wereserve theright for any errors in text or images

and for making any necessary technical changes to this document.

Ifyou should have any questions concerning technical problems

please contact our CustomerServices.

Product description

Theresidual current device’s main function is to protect people and

property if insulation failure should occur in electrical equipment.

Theresidual current device is agood complementary protection to

other safety precautions measures such as fuses and earthing.

This residual current device is anon-latching type which means that

it has ano-volt release switch which has to be reset manually after

apowercut.

• For plugging directly into anearthed wall socket.

• Trips at 30 mA fault current (mA = one thousandth of anampere).

• Equipped with test button and indicator.

• Protection class IP44 (32-3492 only).

Safety

• Make sure that theelectrical socket that theproduct is plugged

into is easily accessible in case it and theconnected product need

to be quickly disconnected from themains electricity.

• Do not connect products of this type to each other.

• Do not cover theproduct.

Operation

Residual current device

RCDs operate by measuring thecurrent balance between thelive

and neutral conductor in acircuit. Whenacircuit operates normally,

thesupply and return currents are in balance and sum to zero. Ifthere

is afault in thecircuit (suchas dangerous current leakage through

thebody of aperson to earth), thecurrent will be out of balance and

theRCD will trip and cut off thesupply of current.

Theoperation of theRCD should be checked regularly using thetest

button.

No-volt release switch

Thebuilt-in no-volt release switch prevents theconnected electrical

device (drill, lathe, etc.) from starting again automatically after apower

cut. Theno-volt release switch must be reset by pushing the[ RESET ]

button twice after apower outage before it will allow current to

ﬂowagain.

Use

Theresidual current device is designed to be plugged into anearthed

wall socket.

Plug theRCD into anelectrical socket and press [ RESET ]

twice in order to reset theno-voltage release switch inside before

theRCD’s socket is energized. Asmall orange dot can be seen in

theindication window above the[ RESET ] button when theRCD’s

socket is energized.

Note: Onlyplug theresidual current device into sockets where it can

be inserted with the[ RESET ] button located above thesocket. (Only

applies to theNordic countries)

Testing the RCD

1. Before theresidual current device is used it must be tested by

pushing the[ TEST ] button.

2. Theorange dot in theindication window above the[ RESET ]

button disappears when theRCD trips and cuts off thecurrent to

thesocket.

3. Reset theRCD by pressing the[ RESET ] button twice. Theorange

dot in theindicator window should be visible when theRCD has

been reset and conducts current to thesocket again.

Note: Thetest button only works when theRCD is plugged into alive

electrical socket.

Responsible disposal

This symbol indicates that this product should not

be disposed of with general household waste. This

applies throughout theentire EU. In order to prevent

any harm to theenvironment or health hazards

caused by incorrect waste disposal, theproduct must

be handed in for recycling so that thematerial can be

disposed of in aresponsible manner. When recycling

your product, take it to your local collection facility

or contact theplace of purchase. They will ensure

that theproduct is disposed of in anenvironmentally

sound manner.

Specifications

18-2032 32-3492

Type EMP200-UK EMP200S-1

Protection class ClassA ClassA

Rated voltage 220–240 VAC 220–240 VAC

Rated current 13 A16A

Apparent power

breaking capacity 3120 VA 3680VA

Tripping current 30mA 30mA

Tripping time < 30ms < 30ms

Protection class IP20 IP44

Operating temperature –25 to +40 °C –25 to +40 °C

Current draw 1.2W 1.2W

Certiﬁed by TÜV Semko

Note: Alwaysperform afunction test before connecting aload to

theresidual current device’s outlet.

Contact our customer services if thetest of theresidual current device

failed or if you suspect that it does not workproperly.

Produkt Specifikationer

Mærke:	Cotech
Kategori:	Strømafbryder
Model:	EMP200S-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Cotech EMP200S-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Strømafbryder Cotech Manualer

Cotech EMP200S-1 Manual

27 August 2024

Strømafbryder Manualer

Nyeste Strømafbryder Manualer

Schneider ComPact INV1000 Manual

30 December 2025

30 December 2025

30 December 2025

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024