CradlePoint CBA250 Manual

CradlePoint Ikke kategoriseret CBA250

Læs gratis den danske manual til CradlePoint CBA250 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15 anmeldelser. Har du et spørgsmål om CradlePoint CBA250, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Cellular

Broadband Adapter

CBA250

Quick Start Guide

11 Connect Power:

To setup the CBA250, unbox

the packaging. Next, plug the

power adapter into the CBA250 ﬁrst,

then plug the adapter into the wall

socket.

12 Connect Device:

Plug in an activated USB or

ExpressCard device into the

appropriate slot. Note that your

device must be on the supported list.

For more information:

http://www.cradlepoint.com/support

O - Configuration mode

I - Normal mode (Pass Through)

LED Status:

1. Power

On - Solid Green

2. Ethernet

Connected - Solid Green

Activity - Blinking Green

3. Not Used

4. USB Status

Standby/Connecting - Orange

Connected - Solid Green

Activity - Blinking Green

Red - Unsupported Device Error

1 2 3 4 5 6

5. ExpressCard

Standby/Connecting - Orange

Connected - Solid Green

Activity - Blinking Green

Red - Unsupported Device Error

6. Signal Strength

Signal strength is displayed in 4

bars but is measured in half

bars. A full bar will be solid, and

a half bar will blink.

Parts List:

Cellular Broadband Adapter

Power Adapter

Quick Start Guide

Notice: Taking these actions will erase all settings and changes

you have made to the router. All passwords and settings will

return to the factory defaults.

Manually Updating Firmware

1. Switch the unit to Conﬁguration mode - O.

2. Connect to the adapter via Ethernet.

3. Use a browser to access the Admin page (http://192.168.0.1).

4. The Admin password is the last six digits of the unit’s MAC address.

5. Select the 'Tools' tab on the top, then the 'Firmware' menu on the left.

6. Select the button “Check Online Now for Latest Firmware Version”

7. Select the Upgrade Router button. (If new Firmware available.)

8. Do not turn oﬀ or unplug the device while it is upgrading.

9. The upgrading process should take a few minutes.

Factory Reset

1. Ensure the adapter is unplugged from the wall socket.

2. Press and hold the reset button.

3. Continuing to hold the reset button, plug the device into a power source.

4. Release the reset button when the lights ﬂash (10 seconds).

5. The adapter will restart and be available on the default settings.

13 Connect LAN:

Connect a client device to the

CBA250 with an Ethernet cable.

For most users, the CBA250 can be used without congura-

tion. When needed, the Cong switch is used to place the

unit in the conguration mode. Conguration mode is used

to setup user parameters, download new Firmware and

enable cellular modem diagnostics.

Conguration mode is accessed by browsing to the Admin

page at http://192.168.0.1

FCC Statement:

This equipment has been tested and

founnd to comply with the limits for a

Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment oﬀ and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit diﬀerent

from that to which the receiver is connected

• Consult the dealer or an experienced radio or television

technician for help

Changes or modiﬁcations not expressly approved by

CradlePoint, Inc. could void the user’s authority to operate the

product.

Radio Frequency Interference Requirement - Canada

This Class B digital apparatus complies with Canadian ICES-

003. Cet appareil numérique de la classe B est conforme à la

norme NMB-003 du Canada.

Quick Start Guide - Continued

http://www.cradlepoint.com

Produkt Specifikationer

Mærke:	CradlePoint
Kategori:	Ikke kategoriseret
Model:	CBA250

Har du brug for hjælp?

Hvis du har brug for hjælp til CradlePoint CBA250 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CradlePoint Manualer

CradlePoint CBA250 Manual

11 August 2024

CradlePoint 2100LP3-EU Manual

8 August 2024

CradlePoint MC100E-VZ Manual

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025