Creda T510 Manual
Creda
Tørretumbler
T510
Læs gratis den danske manual til Creda T510 (24 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Creda T510, eller vil du spørge andre brugere om produktet?
Side 1/24
Tumble Dryer
Instruction Book
5kg Models
You must read these instructions prior to using the
appliance and retain them for future reference.
2
Safety Advice 3-4
Electrical Requirements 5
Features - Get to know the main parts of your Dryer 6
Where to put and vent your Dryer 7-8
How to use your Dryer 9
The Controls 10-13
Sorting your laundry 14
Wash Care Labels 15
Items not suitable for tumble drying 15
Items requiring special attention 16
Speedy Iron Programme 17
Guide to Drying Times 18
How to remove and clean the fluff filter 19
Caring for your Dryer 20
If something goes wrong 22
Key Contacts Back Cover
Contents
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on
the safe and proper use of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make
sure this Book is also provided so the new owner can become familiar with the appliance
and safety warnings.
If the Book is lost or damaged a copy may be obtained from:
GDA Ltd., Morley Way, Peterborough, PE2 9JB
4
For your safety
ALWAYS ● When the dryer is not in use, switch off at the wall, remove plug
and close the door.
ALWAYS ● Comply with the specified electrical requirements.
ALWAYS ● Ensure that your dryer is installed correctly and has adequate
ventilation. (see, "Where to put and vent your dryer.")
ALWAYS ● Use the vent hose for optimum drying performance.
ALWAYS ● Finish every programme with the cool tumble cycle provided on
the control.
ALWAYS ● Clean the filter, it is essential that the filter is kept clear of fluff
after EACH drying cycle.
ALWAYS ● Observe the rules for drying garments:
In particular woollen articles should not be dried in a
tumble dryer unless they are labelled ‘Superwash’,
‘Machine washable’ or have the ‘May be tumble dried’
symbol:
If in any doubt do not dry wool in the machine.
Unlike other materials, the mechanism of wool
shrinkage is irreversible, i.e. it will not stretch back to
the original size and shape.
ALWAYS ● Buy genuine accessories and spares.
CAUTION: WHEN THE DRYER IS IN USE AVOID
TOUCHING THE REAR OF THE DRYER AS IT MAY BE
HOT.
Electrical Requirements
Supply
Changing
the fuse
Moulded plug
Changing
the plug
Rewirable plug
Changing the
mains cable
WARNING:This appliance must be earthed!
REFER TO THE RATING PLATE FOR VOLTAGE AND CURRENT
REQUIREMENTS. (see diagram for location.)
The flexible mains lead is supplied fitted with a BS1363 plug and
with a 13 amp BS1362 fuse.
The plug should be connected to the mains supply via a suitable
switched socket which is accessible after installing your dryer.
If it is necessary to fit a replacement fuse, it must be a 13 amp
ASTA approved to BS1362 type.
If a replacement fuse holder/cover is required, it must be of the
same colour coding or wording as shown on the base of the plug.
Replacements are available from your Spares stockist.
The wires in the mains lead are coloured in accordance with the
following:
GREEN/YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE
If a replacement plug is to be fitted, the appropriate wire must be
connected to the correct terminal,as follows:
Connect:
Green/Yellow to terminal marked Earth or Green or
Blue to terminal marked Neutral or N or Black
Brown to terminal marked Live or L or Red.
If the plug being replaced is a non-rewirable type then the cut-off
plug must be disposed of safely. DO NOT leave where it can be
inserted into a socket and create a shock hazard.
Should the mains lead ever require replacing at any time please
contact your nearest Service Centre. A charge will be made for the
replacement of the mains lead or if you require a longer lead.
The mains lead must only be replaced by a specially prepared
cable obtainable from your Spares Stockist and fitted by a
qualified electrician.
WARNING:The plug must not be used without a fuse cover.
NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A
QUALIFIED ELECTRICIAN.
GREEN &
YELLOW TO
EARTH
13 AMP
FUSE
BROWN
TO LIVE
CORD
CLAMP
BLUE TO
NEUTRAL
5
6
Features - Get to know the main parts of your dryer
Model and
serial numbers
Vent Cover
Fig. 4
Wall/window vent
(Vent cover at front)
NOTE: if your dryer is new wipe out
the inside of the drum before you first
use it to remove any dust which may
have accumulated during transit.
See “The Controls”
FLUFF FILTER
Clean after
each use
Front vent with hose
(Vent cover at rear)
Rating Plate
Air Intake
grill
Vent hose
fitted here
Caution
Hot
Fig. 3
Rear venting with hose
(Vent cover at front)
Drum
Fig. 2
Fig. 1
9
How to use your dryer
1. Plug in, switch
on electricity.
2. Sort your laun-
dry (see section
“Sorting Your
Laundry”)
3. Open the door.
Check that the fluff
filter is clean (see
section How to
remove and clean
the fluff filter).
4. Load the dryer
placing the clothes
carefully in the drum
pushing them well
towards the back
and away from the
door seal. Close the
door.
5. Select the relevant heat setting
(see section “Sorting Your Laundry”).
When low heat is selected a coloured
indicator (on top of switch) will be
visible.
6. (Selected models only)
Select Alarm (Buzzer) option, if required.
The buzzer is selected with the switch
button ‘IN’ and cancelled with the button
‘OUT’.
8. When finished
open the door and
take out the laundry.
Clean and replace
the fluff filter.
7. Select the
required
programme/ drying
time (See section
“The Controls”).
The dryer will start.
WARNING:
WHEN SWITCHING
ELECTRICITY ON
OR OFF, PLEASE
ENSURE THAT
YOUR HANDS ARE
DRY.
WARNING:
WHEN SWITCHING
ELECTRICITY ON
OR OFF, PLEASE
ENSURE THAT
YOUR HANDS ARE
DRY.
Button IN
Alarm ON
Button IN
HIGH HEAT
Button OUT
LOW HEAT
(Gentle)
Button OUT
Alarm OFF
Never switch the dryer off with a HOT load in the drum.
You must terminate every programme with the Cool Tumble Phase.
9. Switch off
electricity and remove
plug from socket.
10
Timer control
The Cool Tumble
phase
Heat Switch (OUT low heat, IN high heat) Indicator
Turn the timer clockwise from the zero position slightly past the
required time, then back to the required time.
The drying time for both heat settings is controlled by the timer.
Do not rotate the knob beyond 120 minutes (maximum drying time),
or past the zero stop. If you have selected more time than you require
turn the knob anti-clockwise to select the correct time required.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in. The “Guide To Drying Times” section will tell
you how much time you’ll need for various loads.
About 10 minutes before the programme is completed, the heating
elements will be switched off and the programme enters the final ‘Cool
Tumble’ phase. During this phase the fabric is cooled. You should
always allow the dryer to complete this phase.
By opening the door, the dryer will stop and you can check the dryness
of the load a often as you wish and, if you want, remove (or add) some
items before they are fully dry. (This is particularly useful for a mixed
load where you want to iron some items, but others are to be fully
dried).
We recommend that the clothes are removed immediately after this
programme to minimise creasing.
The Controls - Basic Models (not 2-way Tumble models)
11
The Controls - Reverse (2-way Tumble models)
Timer control
The Cool Tumble
phase
Heat Switch (OUT low heat, IN high heat)
Turn the timer clockwise to select the required drying time.
The drying time for both heat settings is controlled by the timer. All you
have to do is turn the Timer Control clockwise until the required time
appears in line with the indicator.
Never wind the timer control anti-clockwise.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in. The “Guide To Drying Times” section will tell
you how much time you’ll need for various loads.
About 10 minutes before the programme is completed, the heating
elements will be switched off and the programme enters the final ‘Cool
Tumble’ phase. During this phase the fabric is cooled. You should
always allow the dryer to complete this phase.
By opening the door, the dryer will stop and you can check the
dryness of the load a often as you wish and, if you want, remove (or
add) some items before they are fully dry. (This is particularly useful for
a mixed load where you want to iron some items, but others are to be
fully dried).
We recommend that the clothes are removed immediately this
programme is finished to minimise creasing.
Indicator
12
The Controls - Excel Auto Sensor models
Programme
options
i) Automatic
Drying
Heat Switch (OUT low heat, IN high heat) Sensor Drying Light
Alarm Switch Indicator
To set the required programme, all you have to do is turn the Timer
Control clockwise until the required selection appears in line with the
indicator. Never turn the timer control anti-clockwise.
This operation also starts the dryer, provided the door is closed and
the machine is plugged in.
1. Sensor (Automatic) Drying B (average) loads
2. Sensor (Automatic) Drying A (large) loads
3. Speedy Iron Cycle
4. Timed drying (up to 60 minutes)
5. Cool Tumble Phase
The Sensor Drying programmes will automatically dry most loads to
the fully dry ready to wear condition. This eliminates the need to guess
the drying times and saves energy. High Heat MUST be selected.
(Heat switch IN). To select Sensor Drying turn the selector to position:
B for average loads and A for large loads.
B ‘Sensor’ Drying average loads
1 to 3kg Cottons, Polycottons or Synthetics (Dry Weight).
A ‘Sensor’ Drying large loads
3 to 5kg Cottons (Dry weight)
When the door is closed the Sensor Drying light will glow to indicate
that Sensor Drying programme is running. When the load is dry, the
selector will automatically advance to the 8 minute cool tumble phase.
Note:
• If LOW (Gentle) heat is selected for a Sensor Drying
programme, the dryer will advance to COOL without drying
the load.
• For acrylics and acrylic mixtures, select LOW heat and use
timed drying.
• Small loads (less than 1kg) must be dried using the timed
drying programme.
13
The Controls - Auto Sensor models (continued)
Sensor Drying
Light
ii) Speedy Iron
Cycle
iii) Timed Drying
iv) Cool Tumble
Phase
This light will glow when Sensor Drying is selected. it will stop glowing
when the load is dry and the programme advances to the Cool Tumble
phase.
This is a short programme of approximately 10 minutes to condition
previously dried clothes (See section “Speedy Iron Programme”).
It consists of a period of heating followed by a short cool tumble
period (as detailed below).
Select high heat for this programme.
It should not be used on damp loads, as it is NOT a drying
programme.
To set the required time, all you have to do is turn the timer control
clockwise until the required time appears in line with the indicator.
Never turn the timer control anti-clockwise.
The chart in the section “Guide to Drying Times” will tell you how much
time you’ll need for various loads.
This programme is particularly useful in cases where a damp load is
required for ironing or LOW heat drying is required and also for small
loads.
About 10 minutes before the programme is completed, the heating
elements are switched off and the programme enters the final ‘Cool
Tumble” phase.
During this phase the fabric is cooled. You should always allow the
dryer to complete this phase.
By opening the door the dryer will stop and you can check the dryness
of the load as often as you wish and if you want to remove (or add)
some items before they are fully dry. (This is particularly useful for a
mixed load where you want to iron some items, but others are to be
fully dried).
After this cycle, the ready signal (Alarm) will sound (if selected) to
remind you that the clothes are ready to take out. To cancel, turn the
timer to ‘0’ or press the option button (to its OUT position).
We recommend that the clothes Are removed immediately this
programme ends to minimise creasing.
14
Sorting your laundry
1. Always separate laundry into the correct fabric groups before
washing and drying.
2. See that all zips are closed, hooks and eyes are fastened and
belt, strings etc. are tied loosely in bows, you will normally have
done this for each item before the washing stage.
3. It is important to extract as much water as possible from each
item before drying. This saves you time and money.
4. Make sure that the items to be dried are suitable for tumble
drying, or are not of a type requiring ‘special attention’ (see“Wash
Care Labels” section).
Your dryer will hold a load of 5kg (11lb) dry weight of natural fabrics.
if you are drying items of man-made fibres (synthetic or acrylics), the
maximum load should not exceed 3kg (6.6lb) dry weight.
This difference is that man-made fibres require more space to
tumble-dry without creasing.
To help you estimate how many items it takes to make up a drying
load, the charts below show the approximate weights of some
everyday washing items.
If you group small cotton or terry-towelling items with a synthetic
fabric load they could be damp at the end of the drying cycle. If this
happens simply give them an additional short period of drying to
finish them off.
Maximum
load size
Typical load
WARNING: CLOTHES SHOULD NEVER BE LOADED
DRIPPING WET
WARNING: DO NOT OVERLOAD AS THIS COULD RESULT IN
REDUCED DRYING PERFORMANCE AND A POSSIBLE FIRE
HAZARD.
Clothes
Blouse Cotton 150g 5oz
Other 100g 3
1
/
2
oz
Dress Cotton 500g 1lb 2oz
Other 350g 12oz
Jeans 700g 1lb 6oz
10 Nappies 1000g 2lb 3oz
Shirt Cotton 300g 10
1
/
2
oz
Other 200g 7oz
T-Shirt 125g 4
1
/
2
oz
Household Items
Duvet cover Cotton 1500g 3lb 5oz
(Double)
Other 1000g 2lb 3oz
Large Tablecloth 700g 1lb 6oz
Small Tablecloth 250g 9oz
Tea Towel 100g 3
1
/
2
oz
Bath Towel 700g 1lb 8oz
Hand Towel 350g 12oz
Double Sheet 500g 1lb 2oz
Single Sheet 350g 12oz
15
Wash Care Labels
Most of today’s fabrics can be tumble dried in your Dryer with no
trouble at all, but there are certain fabric finishes which should be
dried away from direct heat.
The majority of garments now have wash-care labels on them, giving
full washing and drying instructions. These should always be followed
carefully especially when you are drying something for the first time.
Typical symbols are:
May be tumble dried
Do not tumble dry
Or:
Tumble dry at high heat setting
Tumble dry at low heat setting
• Those containing foam rubber or rubber-like materials or plastic
film (e.g. pillows, cushions, PVC rainwear), or any other articles
which are inflammable or contain inflammable substances (e.g.
towels contaminated with hair lacquer
• Fibreglass (e.g. some types of curtains)
• Items which have been dry cleaned
• Woollens. Woollen items need as much care in drying as they do
in washing. The movement of the tumble-drying action causes the
woollen fibre to shrink and distort.
• Garments with the ITCL Code (see ‘Items Requiring Special
Attention’).
Do not tumble dry.
• Large bulky items e.g. continental quilts, sleeping bags, pillows,
cushions, double blankets and large bedspreads. These expand
when drying and would prevent airflow through the Dryer.
WARNING: THE DRYER IS INTENDED FOR USE ONLY
WHERE WATER SOLUTION IS USED FOR THE CLEANING
PROCESS. MISUSE OF A TUMBLE DRYER MAY CREATE A
FIRE HAZARD.
Items not suitable for tumble drying
16
Items requiring special attention
The drying requirements of blankets and bedspreads will, of course,
vary tremendously according to size and weight. Some, however are
simply too big. if you have difficulty getting them into the Dryer, the
machine will have difficulty drying them properly. Blankets (and
Garments) made from Acrylic fibres (e.g. Acilan, Courtelle, Orion and
Dralon) must be dried with special care on Low heat setting.
Overdrying should be avoided to ensure heat creasing does not
occur.
Your dryer will cope with such clothes very well, but you should
always read the manufacturer’s drying instructions attached to the
garment before you begin.
Starched articles should be dried together in the same load to avoid
the distribution of starch to non-starched items. You should use a
slightly heavier starch solution than you would when drying the items
on the washing line. Make sure that as much of the solution is
removed from the load as possible before placing it in the Dryer.
Remove the items from the dryer as soon as they reach ironing
dampness. If they are overdried the starch will powder, leaving the
fabric limp - which rather defeats the purpose of the exercise!
To make sure all your tumble dried clothes come out really fresh and
soft we recommend you use a liquid fabric conditioner in the final
rinse of your wash. A liquid fabric conditioner restores bounce and
softness and helps eliminate static cling.
Garments with the ITCL code may be cleaned using one of the
Home Dry Cleaning Kits available.
The instructions supplied with the Home Dry Cleaning Kit must be
strictly followed.
Blankets and
Bedspreads
Permanently
pleated or creased
garments
Starched articles
Fabric conditioner
Home dry cleaning
WARNING: ON NO ACCOUNT SHOULD LIQUID OR SHEET
FABRIC CONDITIONER BE ADDED TO THE DRYER ITSELF.
17
Speedy Iron Programme - Selected models
When to use
‘Speedy Iron’
Important!
Alarm Signal
‘Speedy Iron’ provides a short programme consisting of approximately
7.5 minutes of heat with an approximately 2.5 minutes cool tumble
period. It is a short conditioning programme that softens the fibres
allowing them to relax making handling and ironing easier and less time
consuming.
However garments are dried, outside on the line, inside on a radiator,
hung around the home or using a tumble dryer, once dry they usually
get left in the same position/place for a long period of time. This tends
to cause garment fibre stiffness which can make the handling of
garments difficult and therefore the ironing time longer. Garments dried
in any of the ways described above and left will benefit from the ‘Speedy
Iron’ programme.
● The ‘Speedy Iron’ cycle is not a drying programme. It has been
designed to condition/soften garments that have already been
dried and left unattended in this state for a period of time.
● All materials do not behave in exactly the same way when heated.
For instance, our testing has shown that materials such as
Tencel® and Acrylics are not relaxed quite as effectively by
applying the ‘Speedy Iron’ cycle as was found on the more
traditional Cottons and Polycottons.
● To obtain the best results from ‘Speedy Iron’ it is important that the
weights recommended below are not exceeded and high heat is
selected. (Heat switch IN).
● For best results we recommend garments should be
removed from the dryer immediately after the ‘Speedy Iron’
programme to be hung, folded neatly or ironed.
When this is not possible the ‘Speedy Iron’ programme should
be repeated.
Recommended weights and materials
On completion of the programme an alarm signal is sounded (if
selected) to remind you to remove garments from the dryer.
Material Maximum load
Cotton and Cotton mixtures 2.5kg
2kg
2kg
5.5lb
4.4lb
4.4lb
Synthetics
Denim
19
How to remove and clean the fluff filter
Position of filter
To remove the filter
A very important part of your dryer is the fluff filter at
the front edge of the drum. It’s there to trap the parti-
cles of lint and fluff which are normally blown away
when clothes are dried on the washing-line.
if the filter is allowed to become blocked, the passage
of warm air through the drum will be severely restrict-
ed. This means your clothes will take much longer than
normal to dry and the cost of drying them will be
increased. it may also damage your dryer.
Small items, e.g. babies socks, may fall onto the filter.
These should be removed so that the filter is not
restricted.
Grip the centre rib and pull the filter upwards and for-
wards through the door seal (see diagram).
Open the filter, and remove the fluff that has collected
on the inside.
Wash or vacuum clean the filter occasionally.
Don’t be alarmed by the amount of fluff you may find on
the filter. It’s part of the wearing, washing and drying
process.
It is essential that the filter is replaced correctly. It must
be fitted so that the symbols, shown on the filter above,
face towards the front of the dryer. Ensure the filter is
fully located into the tumble dryer duct.
WARNING: NEVER USE SHEET FAB-
RIC CONDITIONER. IT MAY FALL INTO
THE FILTER AND RESTRICT THE AIR-
FLOW THROUGH THE DRYER
WARNING: DO NOT OPERATE THE DRYER
WITHOUT CLEANING THE FILTER AFTER
EACH DRYING CYCLE. FAILURE TO CLEAN
THE FILTER MAY RESULT IN A FIRE HAZARD.
WARNING: DO NOT OPERATE THE DRYER
WITHOUT THE FILTER IN POSITION.
20
Caring for your Dryer
When finished
After each load
As necessary
Lubrication
Your tumble dryer needs very little attention. The following simple
steps will keep it performing well.
Switch off electricity and remove plug.
Always clean the filter and turn the drum by hand to check that small
items like handkerchiefs do not get missed.
Clean exterior metal and plastic surfaces with a damp cloth or silicon
polish only. Regularly check and clean if necessary, the vent hose and
any permanent venting fixture to ensure that there has been no accu-
mulation of fluff or lint during the drying process.
Clean fluff from the area below the fluff filter and the rear vent tube.
Do not use abrasive cleaners, scouring agents, acids, chlorine
bleach or metal polish to clean any part of the machine. These could
damage the machine.
Your tumble dryer uses special bearing components. Lubrication by
the user is not necessary and must not be attempted.
We strongly recommend that all appliances are regularly checked for
electrical and mechanical safety.
21
Spare parts
Disposal of your product
Please remember your new appliance is a complex piece of
equipment.
‘DIY” repairs or unqualified and untrained service people may put you
in danger, could damage the appliance, and might mean you lose
cover under the Parts Guarantee.
If you do experience a problem with the appliance don’t take risks,
call in our Service Engineer. Our Spare Parts are designed
exclusively to fit your appliance. Do not use them for any other
purpose as you may create a safety hazard.
To minimise the risk of injury to children please dispose of your
product carefully and safely.
Remove all doors and lids. Remove the mains cable (where fitted) by
cutting off flush with the appliance and always ensure that no plug is
left in a condition where it could be connected to the
electricity supply.
To help the environment Local Authority instructions should be
followed for the disposal of your product.
This appliance conforms to the following EEC Directives.
Low Voltage Equipment
72/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
22
If something goes wrong
First, don’t panic! There may be nothing wrong at all. Look for your
problem below, then check the things we suggest. More often than
not, this will give you the answer to your problem, and you’ll be able
to carry on without having to telephone your Service Centre.
If after this you still cannot get your machine to work, follow the
advice given on the next page.
Check these things first
1. Is the machine plugged in and switched on at the socket?
2. Is the Timer Control set to required programme/time?
3. Is the door securely closed?
4. Has the fuse blown? (Try plugging in another appliance to check)
5. Have you used an extension lead? Many are not suitable. Try
plugging the dryer directly into a socket to check.
1. Have you forgotten to clean the filter? Check it.
2. Have you selected the correct Heat setting for the type of fabric
you are drying? (IN for High, OUT for low (Gentle)).
3. Is the flexible vent hose squashed, blocked or kinked? Check it
for foreign objects or condensate (water).
4. Is the air inlet obstructed in any way?
5. Permanent venting - is flap on the storm cover obstructed?
6. Were the clothes ‘excessively wet’ when they were put in?
7. Was the correct programme/time selected?
8. Have you overloaded the dryer?
1. Has the correct programme been selected for the load?
3 - 5kg programme A
1 - 3kg programme B
Less than 1kg use timed dry programme.
2. Has High heat been selected?
The Sensor Dry programmes will not operate on Low (Gentle)
heat, if low heat is required use timed dry.
This is perfectly normal, the dryer has finished its programme. Press
the Alarm button and the buzzing will stop or turn the Timer Control
to ‘O’, the off position.
Have you re-read this instruction book?
Problem
‘It won’t start’
‘It is taking a long
time to dry’
(All Models)
Sensor Dry
Programmes
(Some models)
‘The dryer keeps
buzzing’ (Some
models)
Any other
problem
Produkt Specifikationer
| Mærke: | Creda |
| Kategori: | Tørretumbler |
| Model: | T510 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Creda T510 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Tørretumbler Creda Manualer
26 August 2025
26 August 2025
10 Juli 2025
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
Tørretumbler Manualer
- Black Decker
- Beper
- Heylo
- DeLonghi
- Panasonic
- Speed Queen
- Insignia
- SanGiorgio
- Lamona
- Zenith
- EAS Electric
- OK
- Black And Decker
- Kernau
- De Dietrich
Nyeste Tørretumbler Manualer
20 September 2025
20 September 2025
19 September 2025
18 September 2025
17 September 2025
17 September 2025
16 September 2025
16 September 2025
16 September 2025
16 September 2025