Crestron HD-TX1-F Manual

Crestron Wifi repeater HD-TX1-F

Læs gratis den danske manual til Crestron HD-TX1-F (2 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Crestron HD-TX1-F, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1
quickstart guide
HD-TX and HD-RX Series
www.crestron.com
Specifications subject to
change without notice.
For Regulatory Compliance information, refer to
the latest version of Doc. 6860.
QUICKSTART DOC. 6861D (2025032) 08.16
HDMI® Fiber-Optic Transmitters and Receivers
The HD-TX and HD-RX Series consist of the following models:
• HD-TX1-F transmitter and HD-RX1-F receiver
• HD-TX3-F transmitter and HD-RX3-F receiver
1Introduction
HD-TX1-F Front Panel Connections
Connecting the HDMI IN Port: Using an HDMI cable (not
supplied), connect the HDMI IN port to the HDMI output port of
the audio/video source.
Connecting the Control Ports: Connect the IR IN or COM
control port or both as follows:
• Using an IR cable (not supplied), connect the 2-pin IR IN:
terminal block of the IR IN port to the IR output port of the
control system.
• : Using a data communications cable (not COM (RS-232)
supplied), connect the 3-pin terminal block to the COM port
of the control system.
HD-RX1-F Front Panel Connections
Connecting the HDMI OUT Port: Using an HDMI cable (not
supplied), connect the HDMI OUT port to the HDMI input port of
the receiving device.
Connecting the Control Ports: Connect the IR OUT or COM
control port or both as follows:
• : Using the CrestronIR OUT ®
IRP2 emitter (not supplied),
connect the 2-pin terminal block of the IR OUT port to the
IR input port of the device to be controlled.
• : Using a data communications cable (not COM (RS-232)
supplied), connect the 3-pin terminal block to the COM port
of the device to be controlled.
HD-TX1-F and HD-RX1-F Rear Panel Connections
Connecting the Ground: Connect the chassis ground lug to
earth ground (building steel).
Connecting the MM OPTICAL Fiber Port: Using a CresFiber
®
or other quality 50/125 μm or 62.5/125 μm simplex multimode
fiber-optic cable with SC connectors, connect one end of the
cable to the MM OPTICAL connector on the HD-TX1-F and the
other end of the cable to the MM OPTICAL connector on the
HD-RX1-F.
NOTE: For maximum distance, the fiber-optic
cable should be rated for at least 500 MHz*km
effective modal bandwidth (EMB) at both 850 nm
and 1300 nm. Refer to the cable manufacturer’s
datasheet for EMB information.
Connecting the 12 Vdc Power Jack:
Connect the 12 Vdc power jack to the
PW-1205RU external power supply included
with the HD-TX1-F and HD-RX1-F.
3HD-TX1-F and HD-RX-1 Connections
HD-TX and HD-RX Series
Mount the transmitter and receiver onto a wall or rack as
appropriate for your installation.
Wall Mounting
Using four mounting screws (not supplied), attach the
transmitter or receiver to the wall as shown below.
Rack Mounting
Mount the transmitter or receiver to the front or rear rail of a
rack as follows:
1. Position either the left or right mounting flanges of the
device so that the holes align with the holes in the rack
(mounting of right flanges is shown below).
2. Secure the device to the rack using two rack mounting
screws (not supplied).
2Mounting
(4) Mounting screws
(not supplied)
Rack mounting
screws
(not supplied)
HD-TX1-F Front Panel Connections
COM
TX
RX
GND
HDMI OUT
IR OUT
S G
Display
HD-RX1-F Front Panel Connections
TX
RX
GND
HDMI IN
IR IN
S G
COM
AV
source
Control
system
HD-TX1-F Rear Panel Connections HD-RX1-F Rear Panel Connections
MM OPTICAL
0.5A
12VDC
CLASS 1
LASER
PRODUCT
USB port
(for factory
use only)
MM OPTICAL
0.5A
12VDC
CLASS 1
LASER
PRODUCT
Fiber-optic cable
USB port
(for factory
use only)
Ground Ground
Power
supply
Power
supply
2
quickstart guide
HD-TX and HD-RX Series
www.crestron.com
Specifications subject to
change without notice.
HD-TX and HD-RX Series
For Regulatory Compliance information, refer to
the latest version of Doc. 6860.
QUICKSTART DOC. 6861D (2025032) 08.16
HDMI Fiber-Optic Transmitters and Receivers
HD-TX3-F Front Panel Connections
Connecting the AUDIO Input Port: Using an unbalanced
3.5 mm TRS mini phone jack cable (not supplied), connect the
AUDIO input port to an unbalanced audio source.
Connecting the USB HID Port: Using a USB cable (not
supplied), connect the USB HID port to a computer.
Connecting the HDMI IN Port: Using an HDMI cable (not
supplied), connect the HDMI IN port to the HDMI output port of
the audio/video source.
Connecting the LAN Port: Using an Ethernet cable (not
supplied), connect the 10BASE-T/100BASE-TX LAN port to the
LAN. Pin designations are listed below.
LAN Port Pin Designations
HD-TX3-F Front Panel Connections
4HD-TX3-F and HD-RX3-F Connections
The specific patents that cover Crestron products are listed at
patents.crestron.com.
Certain Crestron products contain open source software. For specific information,
please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and CresFiber are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. HDMI is either a trademark or registered trademark of HDMI Licensing
LLC in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
AUDIO
USB HID
HDMI IN
LAN
Audio
source
Computer
LAN
Pin 1Pin 8
AV
source
LAN
HD-RX3-F Front Panel Connections
Connecting the AUDIO Output Port: Using an unbalanced
3.5 mm TRS mini phone jack cable (not supplied), connect the
AUDIO output port to an unbalanced audio output device.
NOTE: When the HDMI IN (HD-TX3-F) or HDMI OUT
(HD-RX3-F) port is connected or disconnected or if the HDMI
input resolution changes, the analog audio output is muted for a
few seconds.
Connecting the USB HID Port: Using a USB cable (not
supplied), connect the USB HID port to a mouse or keyboard.
(A keyboard with a built-in touchpad or trackball is supported.
Built-in and external USB hubs are not supported.)
Connecting the HDMI OUT Port: Using an HDMI cable (not
supplied), connect the HDMI OUT port to the HDMI input port of
the receiving device.
Connecting the LAN Port: Using an Ethernet cable (not
supplied), connect the 10BASE-T/100BASE-TX LAN port to the
LAN. (LAN port pin designations are listed in the table in the
left-hand column.)
HD-RX3-F Front Panel Connections
HD-TX3-F and HD-RX3-F Rear Panel Connections
Connecting the Control Ports: Connect the IR or COM
control port or both as follows:
• : Using an IR cable (not supplied), IR IN (HD-TX3-F)
connect the 2-pin terminal block of the IR IN port to the IR
output port of the control system.
• : Using the Crestron IRP2 emitter (not IR OUT (HD-RX3-F)
supplied), connect the 2-pin terminal block of the IR OUT
port to the IR input port of the device to be controlled
• : Using a data communications cable (not COM (RS-232)
supplied), connect the 3-pin terminal block as follows:
- For the HD-TX3-F, connect the COM port to the COM
port of the control system.
- For the HD-RX3-F, connect the COM port to the COM
port of the device to be controlled.
HDMI OUT
AUDIO
USB HID LAN
Display
LAN
Powered
speakers
Mouse or
keyboard
LAN
Pin 1Pin 8
HD-TX3-F Rear
Panel Connections
HD-RX3-F Rear
Panel Connections
IR IN
S G
COM
TX
RX
GND
MM OPTICAL 12VDC
1.5A IR OUT
S G
COM
TX
RX
GND
MM OPTICAL 12VDC
1.5A
Ground
Ground
USB port
(for factory
use only)
USB port
(for factory
use only)
Power
supply
Fiber-optic cable
Power
supply
Control
system Display
CLASS 1
LASER
PRODUCT
CLASS 1
LASER
PRODUCT
Connecting the MM OPTICAL Fiber Port: Using a CresFiber or other
quality 50/125 μm or 62.5/125 μm simplex multimode fiber-optic cable with
SC connectors, connect one end of the cable to the MM OPTICAL
connector on the HD-TX3-F and the other end of the cable to the MM
OPTICAL connector on the HD-RX3-F.
NOTE: For maximum distance, the fiber-optic cable should be rated for at
least 500 MHz*km effective modal bandwidth (EMB) at both 850 nm and
1300 nm. Refer to the cable manufacturer’s datasheet for EMB information.
Connecting the Ground: Connect the chassis ground lug to earth ground
(building steel).
Connecting the 12 Vdc Power Jack: Connect the 12 Vdc power jack to
the PW-1215WU external power supply included with the HD-TX3-F and
HD-RX3-F.
PIN SIGNAL PIN SIGNAL
1 TX+ 5 N/C
2 TX– 6 RX–
3 RX+ 7 N/C
4 N/C 8 N/C

Produkt Specifikationer

Mærke: Crestron
Kategori: Wifi repeater
Model: HD-TX1-F

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron HD-TX1-F stil et spørgsmål nedenfor, og andre brugere vil svare dig


Wifi repeater Crestron Manualer

Crestron

Crestron DM-TX-201-C Manual

21 August 2024
Crestron

Crestron Green Light GLA-EXPEX Manual

21 August 2024
Crestron

Crestron CEN-GWEXER-PWE Manual

21 August 2024
Crestron

Crestron USB-EXT Manual

21 August 2024
Crestron

Crestron HD-TX1-F Manual

20 August 2024
Crestron

Crestron HD-RX1-F Manual

20 August 2024
Crestron

Crestron CENI-GWEXER-PWE Manual

20 August 2024
Crestron

Crestron infiNET C2NI-MNETRPT Manual

20 August 2024
Crestron

Crestron DM-TX-401-S Manual

20 August 2024
Crestron

Crestron DIN-CENCN-2-POE Manual

20 August 2024

Wifi repeater Manualer

Nyeste Wifi repeater Manualer

CSL

CSL 303084 Manual

7 September 2025
CSL

CSL 301427 Manual

7 September 2025
TP-Link

TP-Link AX1500 Manual

5 September 2025
Extron

Extron PowerCage FOX Tx AV MM Manual

28 August 2025
Extron

Extron PowerCage FOX Tx VGA MM Manual

27 August 2025
TP-Link

TP-Link RE655BE Manual

22 August 2025
Vonets

Vonets VAR11N-300 Manual

22 August 2025
Vonets

Vonets VAP11N-300 Manual

21 August 2025
Cudy

Cudy RE1200 Outdoor Manual

21 August 2025
Keenetic

Keenetic Buddy 6 KN-3411 Manual

17 August 2025