Crestron ZUMMESH-PART Manual

Crestron Ikke kategoriseret ZUMMESH-PART

Læs gratis den danske manual til Crestron ZUMMESH-PART (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Crestron ZUMMESH-PART, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ZUMMESH-PART

Zūm™ Wireless Partition Sensor

Installation Guide

Description

The Crestron® Zūm wireless partition sensor (ZUMMESH-PART) is used to facilitate

seamless control between two Zūm spaces.

Powered with 24 VDC, the ZUMMESH-PART conveniently receives power from a

ZUMMESH-SIM or any Crestron 24 VDC power supply (both not supplied).

Zūm Overview

A Zūm space is an area, such as a board room or conference room, that is equipped

with Zūm mesh devices such as dimmers, switches, keypads, and motion sensors.

Zūm mesh devices create a wireless mesh network that facilitates seamless

communication between devices without using an independent wireless gateway.

Centralized control and monitoring is enabled by adding a ZUMMESH-NETBRIDGE

to the space and integrating a ZUMNET-GATEWAY and ZUM-FLOOR-HUB to the

Crestron control system (all not included).

NOTE: The ZUMMESH-NETBRIDGE requires a compatible J-box device (not

included) to provide power.

Install the ZUMMESH-PART

NOTE:

• Install and use this product in accordance with appropriate electrical

codes and regulations.

• Sensors must be mounted on a vibration-free surface.

Determine the Mounting Location

Position the ZUMMESH-PART about 2 ft (0.6 m) away from the partition. If

necessary, the ZUMMESH-PART can be mounted up to 4 ft (1.2 m) from the

partition. The lens on the ZUMMESH-PART must face the partition so that when

the partition is opened, the sensor sees the unobstructed room.

2 ft (0.6 m)

Partition

Mount the ZUMMESH-PART in a 1-gang electrical box:

1. Turn off the system power.

2. Connect the 2-pin terminal block to the 24 and G port on the ZUMMESH-PART.

When making connections, use 14 to 26 AWG wire, strip the ends of the wires

7/16 in (11 mm) (avoid nicking the conductors), and tighten the connector to

5 in-lb (0.5 to 0.6 Nm).

3. Secure the ZUMMESH-PART to the 1-gang box using the included screws. The

sensors must face towards the partition.

4. Attach a decorator style faceplate (not included).

5. Turn the system power on.

Standard 1-gang

electrical box

Ceiling

Mounting

screws (2)

Faceplate

(Not included)

ZUMMESH-PART

Mount the ZUMMESH-PART on a flat surface:

1. Turn off the system power.

2. Remove the two screws from the back of the ZUMMESH-PART and then

remove the bracket. Retain the screws.

3. Install the flat bracket to the back of the ZUMMESH-PART using the screws

removed in step 2.

4. Connect the 2-pin terminal block to the 24 and G port on the ZUMMESH-PART.

When making connections, use 14 to 26 AWG wire, strip the ends of the wires

7/16 in (11 mm) (avoid nicking the conductors), and tighten the connector to

5 in-lb (0.5 to 0.6 Nm).

5. Secure the ZUMMESH-PART to the ceiling using screws that are appropriate

for the mounting surface. The sensors must face towards the partition.

6. Attach a decorator style faceplate (not supplied).

7. Turn the system power on.

Ceiling

Mounting

screws (2)

Faceplate

(Not included)

ZUMMESH-PAR

Adjust the ZUMMESH-PART Sensitivity

The ZUMMESH-PART operates by emitting an IR pulse and then measuring the

reflected IR signal. The measurement of the reflected IR signal and the sensitivity

level determines if the partition is closed or open.

The ZUMMESH-PART has high, medium (default), and low sensitivity levels.

• High: Use when the partition is not being detected due to distance or partition

material.

• Medium (default): Sufficient for most installations.

• Low: Use when the partition is falsely detected due to reflectance from other

objects such as the ceiling, light fixtures, etc.

View and Adjust the Sensitivity Level:

The + and – buttons are used to view and adjust the sensitivity of the

ZUMMESH-PART. The + button increases the sensitivity and the - button decreases

the sensitivity.

To view and change the sensitivity level:

1. Press and hold the + or - button until the PART LED blinks.

• 1 blink: Sensitivity is low

• 2 blinks: Sensitivity is medium

• 3 blinks: Sensitivity is high

2. Continue holding the + button to increase the sensitivity or the - button to

decrease the sensitivity. Release the button when the desired sensitivity setting

is achieved.

3. Open and close the partition to verify the sensitivity level. The green PART LED

lights when the partition is closed. It takes several seconds for the

ZUMMESH-PART to determine that the partition is closed.

LED Functionality

PART LED:

• Lights green when the partition is closed.

• Is off when the partition is open.

NOTE: When the partition is opened or closed, there is a small delay for the

PART LED to change.

RM A LED:

• Lights solid red to indicate that the ZUMMESH-PART has not joined Room A.

• Once joined to Room A, the LED lights momentarily when a message is received

from a device in Room A.

RM B LED:

• Lights solid red to indicate that the ZUMMESH-PART has not joined Room B.

• Once joined to Room B, the LED lights momentarily when a message is received

from a device in Room B.

Add the ZUMMESH-PART to Existing Zūm Spaces

NOTE:

• Scene 1 should be similar for both spaces. Occupancy sensors will recall

scene 1 for both spaces, so you want them both to recall the similar light

values. To set Scene 1, refer to the Zum Light Control System Setup Guide

(Doc. 7957) at www.crestron.com/manuals.

• The ZUMMESH-PART occupies one motion sensor slot in each room. Up

to seven additional motion sensors may be added in each room. When

the partition is opened, all motion sensors operate in unison to determine

occupancy and vacancy.

• Do not mix occupancy and vacancy sensors within the combined rooms.

Both rooms must use either occupancy or vacancy sensors.

Add the ZUMMESH-PART to Room A and then Room B by placing the Zūm spaces

in Joining mode. The ZUMMESH-PART is added using button press sequences

on the Zūm devices in the space. When performing the button press sequences,

remember the following:

• Perform consecutive button presses at a rate of one press per second.

• Transition between button press combinations on the same device within

1 second.

• When moving between devices, begin the next button press sequence before

the 4 minute timeout period expires.

Add the ZUMMESH-PART Using an AC powered Keypad, Dimmer, or Switch

1. Place Room A into Joining mode. Room A is the space where the

ZUMMESH-PART is mounted.

a. Press and hold both the top and bottom buttons until the LED lights.

b. Press the top button once.

c. Press the bottom button once. The LEDs on all devices in the space (except

battery powered devices) flash slowly to indicate that the devices are part

of the space and that the space is in Joining mode.

Press and hold until LED lights

then then

Press 1x

2. Add the ZUMMESH-PART to Room A.

a. Press the + button 3 times. The RM A LED will flash with each button press

and then turn off.

b. Press and hold the + button until the RM A LED on the ZUMMESH-PART

lights. The ZUMMESH-PART is added to Room A.

Press and hold until LED lights

Press 3x

then

3. Press any button on an AC-powered device that is part of the Room A Zūm

space to exit Joining mode.

4. Place Room B into Joining mode as described in step 1 above.

5. Add the ZUMMESH-PART to Room B.

a. Press the - button 3 times. The RM B LED will flash with each button press

and then turn off.

b. Press and hold the - button until the RM B LED on the ZUMMESH-PART

lights. The ZUMMESH-PART is added to Room B.

Press and hold until LED lights

Press 3x

then

6. Press any button on an AC-powered device that is part of the Room B Zūm

space to exit Joining mode.

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	ZUMMESH-PART
Bredde:	106 mm
Højde:	57 mm
Antal pr. pakke:	1 stk
Driftstemperatur (T-T):	0 - 45 °C
Længde:	34 mm