CyberPower DTC36U12V3-G Manual

CyberPower Ikke kategoriseret DTC36U12V3-G

Læs gratis den danske manual til CyberPower DTC36U12V3-G (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om CyberPower DTC36U12V3-G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User’s Manual for

CyberShield

DTC36U12V3-G

OVERVIEW

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack, install, or operate this device.

CAUTION!

CyberShield UPSs are designed to provide a local power solution for

cable telephony, wireless local loop (WLL), and fiber to the home

(FTTH) broadband equipment. FTTx not only needs backup power

to prevent utility power failure, but also supports making emergency

calls (e.g., 911) for help.

The battery can energize hazardous live parts inside even when the AC input power

is disconnected.

Before replacing the battery, make sure the replacement has the same rating:

Certified Valve Regulated Lead Acid Battery, 12V, 7.2Ah maximum.

CAUTION!

To reduce the risk of electric shock, keep the cover on. There are no user-serviceable

parts inside the unit. Please contact us or our dealer for service.

Before replacing the battery, remove conductive jewelry, such as chains, watches and ,

rings. Use tools with insulated handles to avoid high energy, which could pass through

conductive materials and cause severe burns.

To avoid electric shock, unplug power cable from the AC power source before servicing

the battery or installing a computer component.

It is recommended to connect the unit to the required equipment and battery before

plugging in the utility power.

The UPS battery is charging when it’s connected to utility power. The battery is

charging during its first 24 hours of normal operation. Don’t expect full battery capacity

during this initial charging period.

The battery must be supplied by CyberPower. Using improper battery which is not

evaluated with this model could cause a risk and is at the user's own risk.

To store the UPS for an extended period, refer to the typical recharge time in the

specification and recharge the battery every three months to ensure battery life.

To reduce the risk of fire or electric shock, install in an indoor area that both temperature

and humidity could be controlled, and free of conductive contaminants. To find the

acceptable ranges of temprature and humidity, please refer to the specification.

Runtime is based on testing fully-charged and new batteries at normal operating

conditions. Runtime curve is approximate and varies based on battery age, level of

charge at test, environment, and other variables.

Number

Description

Alarm Silence Button

Cold Start Button

Cable Retainer Installation Point

Communication Cable Connector

AC Power Cable Connector

Battery Cover

LED Indicator

INSTALLATION

DESKTOP USE:

1.) Remove the battery cover at the back of the DTC36U12V3 and connect the battery wires.

2.) Connect the communication cable and simply place the DTC36U12V3 on or under a desk to

begin backing up the optical home network.

3.) Plug the AC power cable into wall outlet.

4.) DTC36U12V3 desktop placement is shown as OVERVIEW illustration.

Step 3:

Connect the AC cable to the wall outlet.

Step 2:

a. Connect the communication cable between the DTC36U12V3

and the ONT device.

b. Install the cable retainer to secure the commnication cable.

WALL MOUNT USE:

RECOMMENDED SCREW SIZE

Mounting Surface

1"~1.5"

1/8"

3/16"

5/16"

Step 1:

b. Place the screws into the wall using and required anchors for a secure installation.

c. Place the round portion of the keyhole slots of the unit over the installed mounting screws.

d. Connect the battery connector carefully, reinstall the battery into the unit and secure the strap.

a. Use the enclosed installation paper template to mark the location of the screw holes used to mount the DTC36U12V3 to the wall.

BATTERY REPLACEMENT

As long as utility power is on, you may leave the UPS and connected equipment while replacing a new

battery. (For service personnel reference only)

Step 1:

a. Slide off the battery cover

at the back of the unit.

Step 2:

a. Remove the battery from the enclosure.

b. Disconnect the battery cable connectors.

Step 3:

a. Replace with new battery and reconnect the

battery connector. Make sure the red wire

is connected to the “+” polarity, and the

black wire is connected to the “-” polarity.

b. Slide the battery back into the compartment

and cover the unit.

COLD START

BUTTON FUNCTIONS

The cold start feature is used when utility power is no longer present and a new or fresh

battery is installed to support the load device. Once the new/charged battery is installed,

depress the COLD START button until the 4 LED indicators light up.

Functions

Cold Start Press the COLD START button for 3 seconds.

Reset Output

Instructions

Temporarily Alarm

On/Off

Permanent Alarm

On/Off

Press the ALARM SILENCE button for 1 second to turn the alarm off

for 24 hours. A short beep will occur to confirm the alarm is off.

Press the

ALARM SILENCE

button for 15 seconds to turn the alarm off

for permanently. A short beep will occur to confirm the alarm is off.

Press the ALARM SILENCE button for 1 second again to restore the

alarm. Two short beeps will occur to confirm the alarm is on.

Press the

ALARM SILENCE

button for 15 seconds again to restore the

alarm. Two short beeps will occur to confirm the alarm is on.

Press the

ALARM SILENCE

button for 20 seconds to turn off the

output power, and it will turn on automatically after 15 seconds.

CAUTION! The means of power cord should be connected to a socket-outlet with earthing connection.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Ikke kategoriseret
Model:	DTC36U12V3-G

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower DTC36U12V3-G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CyberPower Manualer

CyberPower BP48VL2U01 Manual

9 December 2025

CyberPower BP36VL2U01 Manual

5 December 2025

CyberPower GX150C2 Manual

4 December 2025

CyberPower CSB706W Manual

3 December 2025

CyberPower PR5000RTXL2UC Manual

3 December 2025

CyberPower PS205U Manual

29 Oktober 2025

CyberPower CS20A-EBP Manual

5 Oktober 2025

CyberPower PDU31009 Manual

20 August 2025

CyberPower CR6U61002 Manual

20 August 2025

CyberPower SM30KPMX Manual

20 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Deye SUN-70K-SG02HP3-AU-EM6 Manual

16 December 2025

Eurosound HDBT70RxP Manual

16 December 2025

Sabrent Rocket SB-DR5U-16GX2 Manual

16 December 2025

KStrong UFS354002 Manual

16 December 2025

ALNO MC4550 Manual

16 December 2025

SkyRC Toro TS120 Manual

16 December 2025

Schlage L9050 Manual

16 December 2025

LG DK2M Manual

16 December 2025

V-TAC VT-81005 Manual

16 December 2025

Deye SUN-12K-SG01LP1-AU-AM3 Manual

16 December 2025