CyberPower Kiosk Commander Manual

CyberPower Ikke kategoriseret Kiosk Commander

Læs gratis den danske manual til CyberPower Kiosk Commander (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15 anmeldelser. Har du et spørgsmål om CyberPower Kiosk Commander, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

PREREQUISITES

Hardware Requirements

 133 MHz or higher Pentium-compatible CPU.

 32 megabytes (MB) of RAM recommended minimum; more memory

generally improves responsiveness.

 20 MB of free Hard-Drive space.

 One available USB port or Serial Port.

 CyberPower UPS.

Operating System

 For 32 and 64 bits x86 Architecture: Windows 8 / 7 / Vista / XP / 2000, Windows Server

2012/2008/ 2003

HARDWARE INSTALLATION

Connect your computer’s power supply to a power outlet on the UPS that has Battery and Surge

protection. Connect the USB or Serial cable from the UPS to the computer in order to establish

communication between the computer and the software. Finally turn on the UPS first and then the

computer.

SOFTWARE INSTALLATION

Kiosk Commander may be installed using wizard mode or text mode. Wizard mode installation is

an interactive installation procedure and will guide you through the software installation step by

step. Text mode installation is done though a console or command prompt with no user interface;

usually text mode is chosen when a mass deployment of Kiosk Commander software is required.

You can also assign a settings file for advanced customization of Kiosk Commander, before

installing with text mode installation, so that additional configuration is not required after the

install.

INSTALLATION IN WIZARD MODE

Commander window will pop-up if auto-run is enabled or, you can run start.exe in the root

directory of the CD drive if auto-run is not enabled.

Figure 1 - Kiosk Commander CD pop-up window

Click ‘Install Kiosk Commander Software’ to initiate the setup wizard and follow the steps to finish

the software installation.

Figure 2 - Kiosk Commander Setup Wizard

Note: By default, the setup wizard will install PowerPanel Personal Edition software in addition to

the Kiosk Commander as shown by the tick box in the figure below. Do not uncheck this box if you

want the software to be able to power cycle the computer in the event of the system hanging.

Figure 3 - Prompt to install PowerPanel software

INSTALLATION IN TEXT MODE

command prompt and change the directory to the CD drive. In our examples, we will assume the

CD drive letter is ‘D’. Following the change to the CD drive, change the directory to ‘Software’.

Initiate the text installation with the ‘setup.exe’ executable. If you have a configuration file to be

used, you must append IMPORT_CONFIG_FILE after ‘setup.exe’.

‘setup.exe IMPORT_CONFIG_FILE=<Full path and filename of configuration file>’

For example:

Kiosk Commander Software

Quick Guide

Figure 4 - Installation command in Command Prompt

The IMPORT_CONFIG_FILE parameter is generally used for assigning settings in a mass

deployment and do not need to be set on each system. Generally, we recommend that you install

Kiosk Commander on one machine first, customize it to your needs, export the settings, save

them as a .ini file and use that file for your mass deployment configuration settings. This will save

time and prevent a new configuration file to be created from scratch. Additionally, the file can be

edited after creation if there are specific settings needed on certain computers.

MONITORING APPLICATION

Because most applications on a Kiosk will be running in a standard user account, please log out

of the administrator account and log back in via a standard user’s account.

In order to assign an application to be monitored, follow the steps below. In our example, the

software will be titled ‘Visitor Kiosk Software’.

 Open Kiosk Commander from Start > All Programs > CyberPower Kiosk Commander.

Figure 5 - Startup Kiosk Commander

The Kiosk Commander screen will appear:

Figure 6 - Kiosk Commander screen

 Click the Monitoring tab.

Figure 7 - Monitoring tab

www.cpsww.com

 Click ‘Add’ to open the Process Setup Wizard.

Figure 8 - Process Setup Wizard

 Click Visitor Kiosk Software from the list and click ‘Next’ to continue.

A dialog window will ask if you want to inspect the resource usage of the process automatically.

Click ‘Yes’ and continue to the next steps.

Figure 9 - Prompt to inspect process

The wizard will automatically inspect the CPU usage and memory usage of the process for one

minute.

Figure 10 - Start the inspection process

The wizard will obtain the minimum and maximum CPU and memory usage that it has observed.

Figure 11 - Finish the inspecting

 Click ‘Next’ button to continue.

The inspection results will apply to the next step; you can adjust these manually in the monitoring

conditions section if necessary.

Figure 12 - Process monitoring conditions

Click ‘Next’ to continue.

Figure 13 - Finish of Adding

 Click ‘Finish’ to complete the setup wizard.

Visitor Kiosk Software application (visitor-kiosk.exe) has been added to the monitoring list.

Figure 14 - Process has added in monitoring

You can click the Summary tab to view the status of Kiosk Commander.

Figure 15 - Summary of Kiosk Commander

Note: You should prevent standard user accounts from changing the configuration of Kiosk

Commander. To allow only administrators to open the Kiosk Commander application, change the

‘kwd.exe’ file (C:\Program Files\CyberPower Kiosk Commander\kwd.exe) permissions.

MONITORING SYSTEM

The default monitoring settings enabled after Kiosk Commander installation are often acceptable

but it is recommended that you check all settings to ensure they are correct for your needs.

In order make the UPS power cycle the PC when the system hangs, first make sure process

monitoring is enabled and that a process has been selected by following the steps in the previous

section. Second, make sure the ‘Power cycle the system if the computer becomes unresponsive’

checkbox is selected and lastly, that the PowerPanel state is ‘Normal’ on the summary page.

Figure 16 - Settings of Kiosk Commander

You must also ensure that the BIOS of the computer being used as a Kiosk is set to restore power

after a power failure. (Please refer to the user manual of the Kiosk equipment or the user manual

for the motherboard used in the Kiosk.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Ikke kategoriseret
Model:	Kiosk Commander

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower Kiosk Commander stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CyberPower Manualer

CyberPower PDU31009 Manual

20 August 2025

CyberPower CR6U61002 Manual

20 August 2025

CyberPower SM30KPMX Manual

20 August 2025

CyberPower PDU31414 Manual

20 August 2025

CyberPower PDU41404 Manual

19 August 2025

CyberPower SM10KADFA Manual

29 Juli 2025

CyberPower SM10KASPA Manual

29 Juli 2025

CyberPower P2WU Manual

24 Juli 2025

CyberPower PDU81102 Manual

22 Juli 2025

CyberPower PDU31005 Manual

22 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

DataVideo PP-ONE X Manual

27 August 2025

Cougar LX500 Manual

27 August 2025

ENTES MM-122 Manual

27 August 2025

Tefal Principio TT1108 Manual

27 August 2025

Sauermann CP 210-R Manual

27 August 2025

ENTES MPR-47S-D Manual

27 August 2025

Panduit VS-AVT-C08-L10 Manual

27 August 2025

Deye SUN-10.5K-G02P1-AU-AM2 Manual

27 August 2025

Dorr CV-02 Manual

27 August 2025

Antelope Audio Eclipse 384 Manual

27 August 2025