CyberPower P303UDBL Manual
CyberPower
Ikke kategoriseret
P303UDBL
Læs gratis den danske manual til CyberPower P303UDBL (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 33 anmeldelser. Har du et spørgsmål om CyberPower P303UDBL, eller vil du spørge andre brugere om produktet?
Side 1/2
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK - Use
only in dry locations and only indoors. plug DO NOT
into another relocatable power tap. DO NOT “daisy
chain” extension cords. DO NOT use with any
aquarium equipment. use if properly DO NOT
grounded outlets are not available. DO NOT install
this device if there is less than 10 meters (30 feet) or
more of wire between the electrical outlet and
electrical service panel. DO NOT use for medical or
life support equipment. This device features an
internal protection that will disconnect the surge
protective component at the end of its useful life, but it
will maintain unprotected power to the load. If this
situation is undesirable for the application, follow the
manufacturer’s instructions for replacing the device.
The conductors used to connect the SPD to the line or
bus and to ground shall not be any longer than
necessary and shall avoid unnecessary bends. DO NOT
plug devices over 2.4A to each USB port.
TECHNICAL SUPPORT
Please contact our Tech Support Department
with installation, troubleshooting, or general
product questions.
• Phone: 1-877-297-6937
• Email: tech@cpsww.com
• Hours of Operation:
Monday – Friday 7:00am – 6:00pm CST
USER MANUAL
3-
3-
Outlet Ext
Outlet Ext
ension Cension Corord
d
with 2 USB Pwith 2 USB Portsorts
P303UMT/P303UDBL/P303UOR
P303UMT/P303UDBL/P303UOR
P303UMT/P303UDBL/P303UOR
P303UMT/P303UDBL/P303UORP303UMT/P303UDBL/P303UOR
1
Copyright © 2020 Cyber Power Systems (USA), Inc. All rights reserved.
CONGRATULATIONS ON YOUR PURCHASE
Thank you for selecting the CyberPower P303UMT/
P303UDBL/P303UOR Extension Cord. This manual
explains the features and operation of the
P303UMT/P303U BL/P303UOR. Please take a few D
moments to read this manual.
EXTENSION CORD INSTRUCTIONS
1. Plug the extension cord into a standard grounded
wall receptacle by fully inserting the plug and
ensure that there are no exposed conductors.
2. Make sure the electronic equipment is turned o
before plugging into the extension cord outlets. Do
not use extension cords to connect equipment to
the extension cord.
FEATURES
1. Standard Grounded Outlets (3)
2. USB Charging Ports* (2)
Connect and charge up to two (2) USB devices.
*USB outlets cannot be used as a USB hub. This
device does not transfer data.
SPECIFICATIONS
• Model Number: P303UMT/P303U BL/P303UORD
• Outlets: Standard Grounded Outlets (3)
• Surge Protection: 350 Joules
• Electrical Rating: 125V/13A/1625W/60Hz
• USB Charging Rating: 5V/2.4A shared
• Clamping Voltage: 900V (L-N)
2
2
1
CONTACT INFORMATION
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CyberPowerSystems.com
LIMITED LIFETIME WARRANTY AND CONNECTED
EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before
using the CyberPower P306UMT/P306UBL/P306UOR (the
“product”). By using the product, you consent to be bound
by the terms and conditions of this limited lifetime warranty
and connected equipment guarantee (together referred to
as this “warranty”). IF YOU DO NOT AGREE TO THE TERMS
AND CONDITIONS OF THIS WARRANTY, YOU SHOULD
RETURN THE PRODUCT FOR A FULL REFUND PRIOR TO
USING IT.
Who is providing this warranty, and what does it cover?
Cyber Power Systems (USA), Inc. (“CyberPower”) provides
this limited lifetime warranty. It only covers the original
purchaser and ends if you no longer own the product. This
warranty covers defects in materials and workmanship in the
product under normal use and conditions. It also covers
equipment connected to the product and damaged because
of the failure of the product. This warranty covers the
product and connected equipment for as long as you own
the product.
How do you open a connected equipment claim?
1. Call us at (877) 297-6937, or write to us at:
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379,
or send us an email at claims@cpsww.com within 10 days
of the occurrence for instructions.
2. When you contact CyberPower, identify the product, the
purchase date, and the item(s) of connected equipment.
Have information on all applicable insurance or other
resources of recovery/payment that are available to the
initial customer, and request a claim number.
3. You must provide a dated purchase receipt (or other proof
of the original purchase) for the CyberPower unit and
connected equipment. You also need to provide a
description of the damage to your connected equipment.
4. Pack and ship the product to CyberPower and the item(s)
of connected equipment, a repair cost estimate for the
damage to the connected equipment, and all claim forms
that CyberPower provides to you. Show the claim number
on the shipping label, or include it with the product. You
must prepay all shipping costs. You are responsible for
packaging and shipment, and you must pay the cost of the
repair estimate.
What will CyberPower do to correct problems?
CyberPower will inspect and examine the product. If the
product is defective in material or workmanship, CyberPower
will replace it at CyberPower’s expense, or CyberPower will
refund the full purchase price you paid for the product
(purchase receipt showing price paid is required). If the
product failed to protect any equipment plugged into it, we
will also send you forms for making your claim for the
connected equipment. We will repair or replace the equipment
that was damaged because of the failure of the product or pay
you the fair market value (NOT REPLACEMENT COST), of the
equipment at of the time of the damage. We will use Orion
Blue Book, another third-party valuation guide, eBay,
Craigslist, or other source to establish that amount. Our
maximum liability is limited to $50,000 for the P306UMT/
P306U BL/P306UOR.D
Who pays for shipping?
We pay shipping when we send items to you; you pay when
you send items to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER: ANY SOFTWARE
THAT WAS DAMAGED, SOFTWARE THAT NEEDS TO BE
REPLACED DUE TO THE FAILURE OF THE PRODUCT, OR
ANY DATA THAT IS LOST AS A RESULT OF THE FAILURE.
THIS WARRANTY DOES NOT COVER THE RESTORATION
OF DATA OR RECORDS, OR THE REINSTALLATION
OF SOFTWARE.
2. This warranty does not cover: misuse, modification,
operation or storage outside of the environmental limits of
the product or the equipment connected to it. It does not
cover damage while in transit or in storage; if there has
been improper operation or maintenance, or use with
items not designed or intended for use with the product,
such as laser printers, appliances, aquariums, medical, or
life support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the initial customer are
those provided by this warranty.
1. This warranty does not apply unless the product and the
connected equipment were connected to properly wired
and grounded outlets (including compliance with electrical
and safety codes of the most current electrical code),
without the use of any adapters or other connectors.
2. The product must have been plugged directly into the
power source. The equipment connected to the product
must be directly connected in the product, not “daisy
chained” together in serial fashion with any extension
cords, another product, or device similar to the product,
surge suppressor, or power tap. Any such installation voids
the warranty.
3. The product and connected equipment must have been
used properly in a suitable environment, in conformance
with any applicable license, instruction manual, or warnings.
4. The product must have been used at all times within the
limitations on the product’s maximum rated wattage.
Where can I get more information?
Contact us at:
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379;
Call us at (877) 297-6937;
Send us an email message at claims@cpsww.com.
PRODUCT REGISTRATION
Prompt product registration assures coverage under the
limited lifetime warranty, and also allows the opportunity of
notifications for product enhancements, upgrades, and
other announcements.
Registration is quick and easy. Go to the Product Registration
Page at CyberPowerSystems.com/registration.
CyberPowerSystems.com
© 2020 Cyber Power Systems (USA), Inc. All rights reserved.
All other trademarks are the property of their respective owners.
This device is manufactured using environmentally-safe
procedures in compliance with the Restriction of Hazardous
Substances (RoHS) directive.
Please join CyberPower in caring for the environment by recycling.
WARNING: This product can expose you to chemicals including styrene,
which is known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov.
K01-0000851-00
CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
3 4
Produkt Specifikationer
| Mærke: | CyberPower |
| Kategori: | Ikke kategoriseret |
| Model: | P303UDBL |
Har du brug for hjælp?
Hvis du har brug for hjælp til CyberPower P303UDBL stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret CyberPower Manualer
20 August 2025
20 August 2025
20 August 2025
20 August 2025
19 August 2025
29 Juli 2025
29 Juli 2025
24 Juli 2025
22 Juli 2025
22 Juli 2025
Ikke kategoriseret Manualer
- Federal Signal
- Lifenaxx
- SetonixSynth
- Consul
- Dreambaby
- Swan
- Zepter
- Atomi Smart
- CaviLock
- Lamax
- Hurtle
- Hartke
- PeakTech
- Hombli
- SKROSS
Nyeste Ikke kategoriseret Manualer
29 August 2025
29 August 2025
29 August 2025
29 August 2025
29 August 2025
29 August 2025
29 August 2025
29 August 2025
28 August 2025
28 August 2025