Danfoss SonoMeter 40 Manual

Danfoss Måling SonoMeter 40

Læs gratis den danske manual til Danfoss SonoMeter 40 (12 sider) i kategorien Måling. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Danfoss SonoMeter 40, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/12
© Danfoss | 2021.10 AQ39012919462001en-010101 | 1
SonoMeter 40
Wired M-Bus protocol description
Operating guide
Table of Contents 1. General structure of protocol 2 ................................................................................................
1.1. General features of protocol 2 ........................................................................................................................
1.2. Data strings 2 ........................................................................................................................................................
2. Selection of the data type 3 ......................................................................................................
2.1. Selection of the data type “All data” 3 .........................................................................................................
2.2. Selection of the data type “User data” 3 .....................................................................................................
2.3. Selection of the data type “Simple billing” (Years logger) 3 ...............................................................
2.4. Selection of the data type “Enhanced billing” (Days logger) 3 ..........................................................
2.5. Selection of the data type “Multi tariff billing” (Months logger) 3 ...................................................
2.6. Selection of the data type “Instantaneous values” 3 .............................................................................
2.7. Selection of the data type “Load management values for management” (Hours logger) 3 ..
2.8. Selection of the data type “Installation and startup” 3 .........................................................................
2.9. Selection of the data type “Testing” 4 .........................................................................................................
2.10. Parameter list for preselecting 4 ....................................................................................................................
3. Data request ............................................................................................................................ 4
3.1. Data request 4 ..............................................................................................................................................................
3.2. Meter data coding 5 ..................................................................................................................................................
3.3. CRC16 checksum calculation algorithm ......................................................................................................... 10
4. Settings the parameters of meter ........................................................................................ 11
4.1. Changing the identification number ............................................................................................................... 11
4.2. Changing the identification number, Manufacturer ID and Medium ................................................. 11
4.3. Changing the primary address .......................................................................................................................... 11
4.4. Changing the data and time of the meter ..................................................................................................... 11
4.5. Changing the yearly set day ............................................................................................................................... 11
4.6. Changing the monthly set day .......................................................................................................................... 11
4.7. Changing the baud rate ........................................................................................................................................ 11
5. Secondary addressing ............................................................................................................ 12
5.1. Selecting of the meter ................................................................................................................................... 12
5.2. Communication with selected meter ...................................................................................................... 12
5.3. Deselection of secondary addressing mode ......................................................................................... 12
2 | AQ39012919462001en-010101 © Danfoss | 2021.10
Operating guide SonoMeter 40 - Wired M-Bus protocol description
1. General structure of
protocol
1.1. General features of
protocol
Meter uses a M-bus protocol .
Default baud rate: 2400 bps, Even, 1 Stop.
Baud rate can be changed.
Protocol is the same for Mbus interface and for optical interface.
Primary address of Mbus is individual for Mbus interface and for optical interface.
1.2. Data strings Data string to meter SND_NKE:
1 2 3 4 5
10h 40h A CS 16h
A - M-bus primary address of meter
CS – control sum (the youngest byte of amount of 2-nd and 3-rd bytes)
Data string to meter SND_UD2
1 2 3 4 5 6 7 8...n-2 n-1 n
68h 68hL L 53h
73h A 51h Data
bytes CS 16h
L - length of string (the number of bytes from 5-th to n-2 byte)
A - M-bus primary address of meter
CS – control sum (the youngest byte of amount of 5-th to n-2 bytes)
Data string to meter REQ_UD2:
1 2 3 4 5
10h 5Bh
7Bh A CS 16h
A - M-bus primary address of meter
CS - control sum (the youngest byte of amount of 2-nd and 3-rd bytes)
Answer of the meter CON:
E5h
Answer of the meter RSP_UD2:
1 2 3 4 5 6 7 8...11 12, 13 14 15 16 17 18,19
68h 68hL L C A CI ID Man Vrs Md TC St Sign
20 ... ... ... ... ... ... n-2 n-1 n
DIF VIF Data DIF VIF Data CS 16h
L - length of string (the number of bytes from 5-th to n-2 byte)
C – „C field“ (08)
A - M-bus primary address of meter
CI - „CI field“
ID – identification number of meter (BSD8, used for secondary addressing, can be changed - see
paragraph 4.1),
Man – Manufacturer code (Danfoss A/S manufacturer code is „DFS“, 10 D3)
Vrs – number of protocol version (0Bh)
Md – code of medium (for „heat / cold energy“: 0Dh)
TC – counter of telegrams
St - meter status code
Sign - 00 00
The bytes 20...n-2 is data from meter:
DIF – code of data format
VIF – code of data units
Data– values of data
CS – control sum (the youngest byte of amount of 5-th to n-2 bytes).

Produkt Specifikationer

Mærke: Danfoss
Kategori: Måling
Model: SonoMeter 40

Har du brug for hjælp?

Hvis du har brug for hjælp til Danfoss SonoMeter 40 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måling Danfoss Manualer

Danfoss

Danfoss SonoSelect 10 Manual

11 Maj 2024
Danfoss

Danfoss SonoMeter 40 Manual

29 November 2023
Danfoss

Danfoss SonoRead 868 Manual

9 Juli 2023

Måling Manualer

Nyeste Måling Manualer

Gossen

Gossen MAVOMAX RK2 Manual

1 August 2025
Gossen

Gossen MAVO-SPOT Manual

1 August 2025
Gossen

Gossen MAVOPAD Manual

1 August 2025
Gossen

Gossen SIXON 2 Manual

1 August 2025
Gossen

Gossen MAVO-MONITOR Manual

1 August 2025
Gossen

Gossen MAVOMAX RK1 Manual

1 August 2025
Gossen

Gossen MAVO-SPOT 2 USB Manual

1 August 2025
Gossen

Gossen MAVOSPHERE Manual

1 August 2025
Kern

Kern ORA 3HA Manual

30 Juli 2025
Phoenix Contact

Phoenix Contact EEM-XM377 Manual

30 Juli 2025