DataComm 45-0072-WH Manual

DataComm Kabler til computere og periferiudstyr 45-0072-WH

Læs gratis den danske manual til DataComm 45-0072-WH (3 sider) i kategorien Kabler til computere og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10 anmeldelser. Har du et spørgsmål om DataComm 45-0072-WH, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Use DataComm Electronics’ Recessed Low Voltage Mid-Size Plate with Duplex Surge Supp to w d your flat panel TV, ressor install lo voltage cables behin
your amplifier or other audio and video devices. This mid ize plate can be in alled uprigh sideways. -s st t,
Features of the 45-0081 Recessed Low Voltage Mid-Size Plate with Duplex Surge Suppressor include:
Compa size fi behind all and large ’s ct ts sm TV
TV re y wa plug cesses completel into the ll
Duplex receptacle for additional devices
IMP INSTRUCTIONSORTANT :
This product is designed for retrofit work only because the electrical outlet x cannot be attached to a stud. bo
This product is designed to alert you if you ever lose surge protection. The Surge Suppressor Receptacle is designed to provide protection against short-
event of a dire lightning strike on the service power line.ct
The Surge Suppressor alerts you to the failure of the surge protection component by means of
an audible signal. alarm sounds, device has “received” power surges in exce of y on as a surge protector. To shut If ss its capacit and is no longer functi ing
off alarm, simply turn the “Alarm Off” screw on the ront of the receptacle clockwise. Note: When alarm sounds and the “Alarm Off” scr is turn off, the f ew
receptacle still nctions as normal duple fu a x receptacle without surge protection.
WARNING:
Before you run your 12/2 or 14/2 w/ground UL approved building wire to the Recessed Low Voltage Mid-Size Plate with Duplex Surge
Suppressor, be sure the power is off by switching the circuit breaker to off or removing the fuse(s). Test the power to make sure the power is
off. Be sure to install the Mid-Size Plate with Duplex Surge S pressor in accordance with the National Electrical Code (NEC) and local codes. up
Installation Instructions:
DataC Elect ic Incomm ron s, .
63 acht ee ee49 Pe r Str t
Norcro , G 30 -1 5 ss A 071 72
888 3. 97.22 7 7
770 2. 20.66 8 5
www m lectroni m.dataco me cs.co
In ll ion struct staion / In at Sheet
DataComm Electronics 45-0081 Recessed Low Voltage Mid-Size Plate with Duplex Surge Suppressor
Parts Included:
1. 45-0081 Recessed Low Voltage Mid-Size Plate
2. Electrical Outlet Box
3. 15 Amp/125 Volt Duplex Surge Suppressor
4. Four (4) Screws
Tools Neede d:
1. Drywall Saw
2. 6 Ft. Tape Measure
3. Pencil
4. Screwdr er iv
Figure 1 – Front View
Figure 2 – Back View
Fig. 1
Fig. 2
Figure 1
Top view - shows needed space between the drywall and the studs.
Receptacle side of the Mid ize Plate should be 3” from the stud but no -S
more than 5” (review picture carefully).
Figure 2
Using the template supplied (see page 3 of instruction sheet), trace the opening needed. Using a drywall saw,
cut a hole in the drywall the size of the template. before tracing your opening. See Figure 1 Remember, the
plates are designed to be mounted between the studs.
Page 1 of 3 10/1/12
Concealed Wiring
(hidden in wall)
Flat Screen TV
Concealed Wiring
(hidden in wall)
Flat Screen TV
2-Pole 3-Wire
Grounded
60 Hz
Total Maximum
Surge Dissipation
Maximum Surge
Current
Surge Protection
Cl ping am
Response Time
15A-125V 480 Joules 15,000 Amps
Hot/Neutral,
H /Ground, ot
Neutral/Grou nd
1 Nanosecond
Fig. 5
Fig. 6
888 3. 97.22 7 7
www m lectroni m.dataco me cs.co
Figure 5
Now fo ws secure the electrical outlet box to the mounting studs on the backside of the use the ur scre provided to
Mid-Size Plate.
Figure 6
Impo tar nt: Before in alling the Recessed Mid-Size Plate with Duplex Receptacle into the template opening, make sure st
to pull your low voltage cables through the low voltage cable opening. If you have more than 4 cables you can remove
the flexible plate that seals the low voltage cable opening. This allows for more cables to be pulled through the opening.
After you have pulled your low voltage or A/V cables through the low voltage opening: Start with the bottom of
the Recessed Mid-Size Plate and slowly slide the plate into the opening. Swing the top of the plate into position until the
entire Mid ize Plate is flush with the wall. Now rew down the ews with wing these wings fa en tightly again the -S sc scr s; st st
back of the drywall.
Figure 7
Your new 45-0081-WH Recessed Low Voltage Mid-Size Plate with Duplex Surge Suppressor is now installed and ready
for the flat panel TV mount to be installed. Install your flat panel TV mounting bracket per the flat panel TV bracket
manufa urer’s in ruction ct st s.
Installation / Instruction Sheet 5-0081 (Continued) 4
Fig. 7
Surge Suppressor Specifications
Inside the Hubbell Surge Protection Receptacles are two 22mm squa MO /15000A of surg protection for ch mode. Meets re V’s providing 240 joules e ea
UL Standards 1449 3rd Edition and 498: CSA Certified.
Damage-alert alarm sounds when surge protection is no longer functioning and keeps sounding until the muting ew is utilized or the receptacle is scr
replaced. Power-on indicator light verifies in antly that power is available at the recept su is y st acle and the ppression circuit full functional; light off means
power has been interrupted, flashing light indicates surge protections circuitry has been damaged.
Replacement surge suppressor can be purchased from DataComm Ele oni or an authorized Hubbell Wiring Device di ibuto ctr cs str r.
3Fig.
4Fig.
Figure 3
Run the source of power to the included electrical outlet box.
Figure 4
Using the supplied Duplex Surge Suppressor, connect the Recessed Mid-Size Plate to the piece of 12/2 or 14/2 with
ground UL approved electrical building wire that you have pulled from a power source. Strip off approximately 3 inches
of the outer jacket of the UL approved building wire. Be careful not to cut the jacket of the inner wires. Connect the hot
line (black) wire to the brass colored terminal screw and neutral (white) wire to the silver colored terminal screw. Be sure
to connect the grounding (green) or bare grounding wire to the green colored terminal screw Once you(see Fig 3).
have wired the supplied Duplex Surge Suppressor, screw the Duplex Surge Suppressor receptac lle into the electrica
outlet box until the receptacle is fi ly secured. rm
Page 2 of 3 10/1/12

Produkt Specifikationer

Mærke: DataComm
Kategori: Kabler til computere og periferiudstyr
Model: 45-0072-WH

Har du brug for hjælp?

Hvis du har brug for hjælp til DataComm 45-0072-WH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Kabler til computere og periferiudstyr DataComm Manualer

DataComm

DataComm 45-0072-WH Manual

31 Juli 2025

Kabler til computere og periferiudstyr Manualer

Nyeste Kabler til computere og periferiudstyr Manualer

Lindy

Lindy 36467 Manual

1 September 2025
Lindy

Lindy 36295 Manual

31 August 2025
Kogan

Kogan KAUSBCCDRDA Manual

29 August 2025
Extron

Extron 70-292-11 Manual

28 August 2025
Extron

Extron 70-962-01 Manual

28 August 2025
Alogic

Alogic ULCVGMN-SGR Manual

27 August 2025
Alogic

Alogic Magforce Trio ULCHDACPD-SGR Manual

27 August 2025
Alogic

Alogic ULCDPMN-SGR Manual

26 August 2025
Alogic

Alogic UCANCHD Manual

26 August 2025
Goobay

Goobay 51349 Manual

26 August 2025