Dell OptiPlex GX200 Manual

Dell Ikke kategoriseret OptiPlex GX200

Læs nedenfor 📖 manual på dansk for Dell OptiPlex GX200 (79 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 36 personer og blev bedømt med 4.8 stjerner i gennemsnit af 18.5 brugere

Side 1/79
Dell™OptiPlex™GX200ServiceManual
Small Form- Factor Chassis Removing and Replacing Parts
Low- Profile Chassis Removing and Replacing Parts
Midsize Chassis Removing and Replacing Parts
Mini Tower Chassis Removing and Replacing Parts
Notes, Notices, and Cautions
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices,
and cautions, and they are used as follows:
Information in this document is subject to change without notice.
©2000 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell and OptiPlex are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation
disclaims any proprietary interest in trademarks and trade names other than its own.
Initial release: 18 April 2000
Last revised: 31 Jul 2000
NOTE: A NOTE indicates important information that helps you make better use of your system.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury.
Back to Contents Page
Low- Profile Chassis — RemovingandReplacingParts:Dell™OptiPlex™GX200
Systems Service Manual
Overview
This section provides procedures for removing and replacing the components, assemblies, and subassemblies in the Dell OptiPlex low-profile
chassis GX200 system.
Unless otherwise noted, each procedure assumes that the following conditions exist:
lYou have performed the steps in "Precautionary Measures."
lYou have removed the computer cover.
lYou can replace or reinstall a part by performing the removal procedure in reverse order unless additional information is provided.
Recommended Tools
Most of the procedures in this file require the use of one or more of the following tools:
lSmall flat- blade screwdriver
lWide flat- blade screwdriver
l#1 and #2 Phillips- head screwdrivers
l1/4- inch nut driver
Also, use a wrist grounding strap as explained in "Precautionary Measures."
Precautionary Measures
Before you perform any procedure in this section, take a few moments to read the following caution for your personal safety and to prevent
damage to the system from electrostatic discharge (ESD).
System Power Supply
Expansion-Card Cage
Riser Boards
System Board Components
Expansion Cards
Memory
Microprocessor/Cooling Fan/Heat Sink Assembly
System Battery
System Board
CAUTION: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE EQUIPMENT
Before you start to work on the system, perform the following steps in the sequence listed:
1. Turn off the computer and all peripherals.
2. Disconnect the computer and peripherals from their electrical outlets. Also, disconnect any telephone or telecommunication lines from
the computer. Doing so reduces the potential for personal injury or shock.
3. If you are disconnecting a peripheral from the computer or are removing a component from the system board, wait 10 to 20 seconds
after disconnecting the computer from the electrical outlet before disconnecting the peripheral or removing the component to avoid


Produkt Specifikationer

Mærke: Dell
Kategori: Ikke kategoriseret
Model: OptiPlex GX200

Har du brug for hjælp?

Hvis du har brug for hjælp til Dell OptiPlex GX200 stil et spørgsmål nedenfor, og andre brugere vil svare dig