Delta Dore TYBOX 827 W RF Manual

Delta Dore Termostat TYBOX 827 W RF

Læs gratis den danske manual til Delta Dore TYBOX 827 W RF (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Delta Dore TYBOX 827 W RF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

• Carefully read these instructions prior to use.

• Do not attempt to repair the unit yourself;

an after-sales service is available.

TYBOX 827

From the RUN mode, override enables:

- for the heating, modification of the temperature

setting (5°C to 30°C) until the next programme

change

- for the hot water, modification of the current

operation (ON/OFF) until the next programme

change

Press a button to “activate” the display.

On the receiver:

- the green LED indicates that the product is

switched on,

- the red LED indicates the status of the output(s):

light on = ON, light off = OFF.

MAN Mode

ONCE Mode

• Override is only accessible in AUTO or ONCE

mode.

• To cancel an active override, press the relevant

button ( or ) or turn the dial.

• These instructions apply to both the TYBOX 817 WRF

and the TYBOX 827 WRF.

• The hot water mode ( ) is only available on the

TYBOX 827 WRF.

1. Presentation

4. Override 5. Information button

3. Choosing the operating mode

6. Date / Time

7. Programming the heating

2. RUN Mode

Time

Heating

and

hot water

modes

Room

temperature

Override

buttons

General mode active

Override

currently active

Information

button

5°C

30°C

6.00

16°C 16°C

20°C 20°C 20°C

18°C 18°C

8.00

11.00

1.00

PM 5.00

11.00

12.00

Period

1 2 3 4 5 6

6.00

16°C 16°C

20°C 20°C

18°C 18°C

8.00

11.00

1.00

PM 5.00

11.00

12.00

Period

1 2 3 4 5 6

MON

SUN

Period

1 6 HH:MM

5°C

30°C

Copy MON ... TUE ...

> 2 sec.

Stand-by

screen:

• Room

temperature

• Current day

and time

Change mode

buttons

Selector dial

TYBOX 827 RF

TYBOX 817- 827 W RF

1 and 2-channel wireless programmers

with built-in thermostat

User guide

Delta Dore hereby declares that the equipment complies

with the essential requirements and other relevant provisions

of the R&TTE Directive 1999/5/EC.

The EC declaration of conformity for this equipment is available,

on request, from:

“Technical info” department

D ELTA DORE - Bonnemain - 35270 Combourg (France)

Email: info.techniques@deltadore.com

Because of changes in standards and equipment, the characteristics given in the

text and the illustrations in this document are not binding unless confirmed.

DD.MM.YY

12.00 (00.00)

11.59 (23.59)

MAN Constant

temperature setting NA

OFF Frost Protection Off

AUTO Follows the programming

ONCE

Follows the ONCE programme.

Return to AUTO mode at the end of the

countdown.

ON NA Permanent ON

Select the mode

by pressing or

repeatedly.

Turn the dial to exit the

setting mode.

5°C

30°C

5°C

30°C

5°C

PERM

365

001

Heating

Hot water

Automatic exit after 30 seconds

if no buttons are pressed and

the dial is not turned.

ONCE mode

end day

Configuration

Time setting

MODE Operating mode

selection

RUN Run the operating

mode selected

Absence mode

CH Heating

programming

HW Hot water

programming

Example: default programme applied from

Monday to Friday:

The programme can be changed for each day.

Periods 2 to 5 can be disabled.

For example, disabling the midday slot

(periods 3 and 4).

To copy the

programming from one

day to the next day.

To return to the program, press the Rbutton

again and hold for 2 seconds.

A simplified programme can be applied

(2 programmable periods) for a set number of days

(ONCE mode).

Current date and

number of days before

service.

Hot water channel status

until ...

Heating channel

status until ...

R: back to previous

setting

R: back to previous

setting

R: back to previous

setting

R: back to previous

setting

Please not that you can’t define hot water

temperature in this programmer

The batteries need changing when the battery level

symbol appears (2 LR03 or AAA 1.5V alkaline

batteries).

Precautions must be taken:

- You have approximately 30 seconds to change the

batteries before the time is reset to zero (if this

happens, reset the time).

- Ensure that the +/- polarities are correctly placed

when the battery is fitted into the unit.

- Do not dispose of used batteries in unauthorised

places (you should respect the environment by

taking the batteries to a suitable collection site).

- Do not recharge them.

Nothing is displayed on the room

unit screen.

There is no power supply.

Check the batteries.

The unit is in time setting mode.

You took too much time in changing the batteries.

Set the time. All the other settings have been kept.

The temperature displayed does not match

the temperature measured in the room

(thermometer).

Refer to the installation guide (menu 2-01).

The programme cannot be modified and the

temperature settings are limited (19 °C +/- 3 °C).

Refer to the Configuration section (menu 1-01).

“SERVICE DUE” is flashing on the display.

There are less than 30 days before the mandatory

service is due.

Contact your maintenance department.

“SERVICE DUE” is displayed on the unit.

The mandatory service date has passed.

The heating works on a set temperature setting

(override possible for 1 day).

The hot water will shut down (override possible for

2, 3 or 4 hours).

Contact your maintenance department.

The heating does not work according to the

required temperature.

If you have a Room Thermostat wired in series

with the programmer, check that this thermostat is

set to maximum.

Your heating system is in Frost-Protection

mode (temperature set in mode).

The dial is still in position, , , CH HWor .

13. Troubleshooting12. Replacing the batteries

Battery level symbol

3 4

Separate the thermostat

from its base unit

Replace the batteries,

taking care to properly align the poles

Lock the thermostat

Place the thermostat

on its base unit

4 5 6 7 8

> 5 sec.

12h

24h

1 2

HH:MM HH:MM

11. Basic configurations (menu 1)

Time

display

selection

12-hour clock (default)

24-hour clock

Automatic

summer/winter

mode

authorisation

Not authorised

Authorised (by default)

User

modification

authorisation

Modification of programme

and temperature settings

(from 5 °C to 30 °C)

authorised (default)

Modification of

programme not authorised and

temperature settings restricted

(19 °C +/- 3 °C)

ONCE

programme

start time

Setting from 12 midnight to

12 noon

(default value: 07:00 AM)

ONCE

programme

end time

Setting from 12 noon to

12 midnight

(default value: 11:00 PM)

9. Absence mode

8. Programming the hot water channel

6.00

8.00

11.00

1.00

5.00

11.00

12.00

1OFF

1ON

2OFF

2ON

3OFF

6.00

8.00

11.00

1.00

5.00

11.00

12.00

OFF

MON

SUN

On/Off

1 3 HH:MM

Copy MON ... TUE ...

> 2 sec.

PERM

365

001

15°C

5°C

Example: default programme applied from

Monday to Friday:

The programme can be changed for each day.

Return

day

Number

of days of

absence

The countdown

begins.

Return to RUN mode

at the end of the

countdown.

ON/OFF periods 2 and 3 can be disabled.

For example, inhibition of the midday slot (ON and

OFF period 2).

To copy the

programming from one

day to the next day.

To cancel the inhibition, press the Rbutton

again and hold for 2 seconds.

A simplified programme can be applied

(2 programmable periods) for a set number of days

(ONCE mode).

R: back to previous

setting

R: back to previous

setting

You can associate your programmer with the

following options:

10. Compatible home automation options

Type of

transmitter

associated

Resulting function

Opening

detector

“Energy saving” function

Heating switches to Frost Protection

mode when a window is opened

(temperature set in mode).

Wireless

outdoor

sensor

Indication of outside

temperature by consulting the

information menu (ibutton).

For information about associating and

using home automation products,

contact:

“Technical info” department

DELTA DORE - Bonnemain

35270 Combourg (France)

Email: info.techniques@deltadore.com

Produkt Specifikationer

Mærke:	Delta Dore
Kategori:	Termostat
Model:	TYBOX 827 W RF

Har du brug for hjælp?

Hvis du har brug for hjælp til Delta Dore TYBOX 827 W RF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Delta Dore Manualer

Delta Dore Tybox Control Manual

28 September 2025

Delta Dore Tybox RF 210 Manual

28 September 2025

Delta Dore Tybox RF 210 XL Manual

28 September 2025

Delta Dore Tybox RF 210 BK Manual

28 September 2025

Delta Dore Tywell Control Manual

20 Juli 2025

Delta Dore Tywell 2050 Manual

20 Juli 2025

Delta Dore Delta 8000 Manual

29 December 2024

Delta Dore Minor 1000 Manual

29 December 2024

Delta Dore Delta 8000 TA BUS Manual

29 December 2024

Delta Dore Tybox 34 Manual

29 December 2024

Termostat Manualer

Nyeste Termostat Manualer

Emerson ST75 Manual

1 Oktober 2025

Homematic IP HMIP-eTRV Manual

30 September 2025

Xavax UT 200 Manual

29 September 2025

Stiebel Eltron RTU-TC Manual

28 September 2025

Stiebel Eltron RTF-TC Manual

27 September 2025

Grässlin Chronostat RTC 7 Manual

26 September 2025

Grässlin Chronostat 800 Manual

26 September 2025

Grässlin Thermio Eco C7SB Manual

26 September 2025

GENERAL Life NORA 270S Manual

25 September 2025

GENERAL Life HT11S Manual

25 September 2025