DeWalt DCB606 Manual

DeWalt Batteri DCB606

Læs gratis den danske manual til DeWalt DCB606 (2 sider) i kategorien Batteri. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 30 anmeldelser. Har du et spørgsmål om DeWalt DCB606, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of E

pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS CALL US TOLL

FREE AT: 1-800-4-DEWALT (1-800-433-9258)

JAW REPLACEMENT INSTRUCTIONS

DC495

COMPONENTS (FIG. 1)

A. Trigger switch/variable speed switch

B. Swivel head shear

C. On/Lock-off control button

D. Hex wrench

E. Battery pack

F. Battery release buttons

Disassembly and Assembly (Fig. 2–5)

WARNING: Turn unit off and disconnect battery pack before

installing and removing accessories, before adjusting or when

making repairs. To prevent inadvertant operation, lock the trigger

switch when the tool is not in use and when storing the tool.

To remove shear head from motor, loosen the two back cap

screws (G) using the hex wrench (D) provided. Remove shear head

(B) from the body by pulling head firmly forward (Fig. 2). Slight

twisting action may be required if head does not slide off easily.

To remove cutter blades from the shear head, completely loosen

the two back cap screws and remove shear head from motor unit.

Loosen the tensioning screw (O) 1/2 turn. Completely loosen all

three cap screws and remove head assembly. Turn assembly over

and remove top half of head and then remove the blades.

To replace blades, place lower jaw (P) onto two pins (R). Apply a

thin layer of grease from the packet (included) around the pin and

on the top side of the blade. Place upper jaw (Q) onto pin. Apply the

rest of the grease provided onto the eccentric (L) on the output shaft

of the motor unit and into the area behind the upper moving blade

in the shear head.

Install replacement washer (S), cone side up, over the pin on top of

the moving blade. Place top half of head back (T) onto bottom half

(U), making sure to align the pin to the hole. Reinstall all three cap

screws (G) and nuts (V), but tighten completely.DO NOT

Slide shear head back onto motor unit, making sure that the

eccentric engages the moving blade. Once the head is on the motor

unit and aligned, tighten all three screws and follow adjustment

procedure below.

To ensure proper blade tension, tighten tensioning screw (O) by

turning clockwise to seat the blades. Next, loosen tensioning screw

by turning counterclockwise slightly to allow blade movement.

NOTE: The tensioning screw should be adjusted to correspond to

material thickness.

FIG. 2

(BACK)

(DOS)

(REVERSO)

G (FRONT / AVANT / FRENTE)

FIG. 3

FIG. 5 N

FIG. 1

FIG. 4

S P

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Batteri
Model:	DCB606

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DCB606 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batteri DeWalt Manualer

DeWalt DCB205BT Manual

29 November 2025

DeWalt DCB203BT Manual

26 November 2025

26 November 2025

25 November 2025

9 September 2025

8 September 2025

DeWalt DCB201-B3 Manual

7 September 2025

DeWalt DCB548 Manual

7 September 2025

DeWalt DCB549 Manual

6 November 2024

DeWalt DCB546 Manual

6 November 2024

Batteri Manualer

Nyeste Batteri Manualer

Goodwe GW14.3-BAT-LV-G10 Manual

23 December 2025

Adventure Kings AKEP-PWRPACK12A_01 Manual

20 December 2025

Milwaukee M18 Fuel PACKOUT VACLINK 0888-20 Manual

15 December 2025

Milwaukee M18 FORGE 48-11-1881 Manual

15 December 2025

Milwaukee M18 Fuel 3006-22 Manual

15 December 2025

Milwaukee 48-11-2001 Manual

15 December 2025

CyberPower RB1290X8 Manual

2 December 2025

NOCO NLP5 Manual

1 December 2025

CamLink CL-DELTA3-27UK Manual

30 November 2025

NOCO NLP20 Manual

29 November 2025