DeWalt DS312 Manual

DeWalt Ikke kategoriseret DS312

Læs gratis den danske manual til DeWalt DS312 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 82 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 41.5 anmeldelser. Har du et spørgsmål om DeWalt DS312, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

DS300 Jobsite Security Cable Lock

DS302, DS306, DS312 and DS324

Replacement Cables

WARNING: Read and understand all instructions and

warnings for this product. In addition, read and follow all

instructions and warnings provided with the DS100 Jobsite Security

Portable Alarm System.

CAUTION: DANGER OF EXPLOSION, INJURY, OR FIRE.

Carefully follow all instructions and warnings on the battery label and

package.

• Never use a damaged or worn out battery.

• Discharged batteries should be replaced only with type CR-123 3.0

Volt Lithium batteries.

• Do not use re-chargeable batteries or attempt to charge batteries.

• Carefully remove the old, discharged battery.

• Do not attempt to open.

• Do not peel the label from the battery.

• Never dispose of a battery in a fire.

• Dispose of used batteries in accordance with local regulations.

• Recycle batteries.

• Always insert batteries correctly with regard to polarity (+ and -)

marked on the battery and the equipment.

• When installing the battery, do not use excessive force. If the bat-

tery does not fit, check to make sure that it matches the polarity

markings.

• Never expose the battery terminals to any other metal object. This

can short circuit the battery.

• Avoid exposure to temperature extremes.

• When not in use, store the battery in a cool, dark, dry place.

• Keep batteries out of reach of children.

FCC REGULATORY STATEMENT (FCC: HCQ3B6ETUMXM)

• This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) the device must accept any

interference received, including interference that may cause unde-

sired operation.

INDUSTRY CANADA (IC: 2309A-ETUMXM)

•NOTICE: This equipment meets the applicable Industry Canada

Terminal Equipment Technical Specifications. This is confirmed

by the registration number. The abbreviation, IC, before the reg-

istration number signifies that registration was performed based

on a Declaration of Conformity indicating that Industry Canada

technical specifications were met. It does not imply that Industry

Canada approved the equipment.

Important

• The Cable Lock needs to be removed before operating the

attached equipment.

• The Cable Lock uses a cable with a stainless steel braid. If the

exterior coating is cut, torn or abraded, the exposed metal could

short out equipment. Immediately replace the cable. Replacement

cables [2' (.61m), 6' (1.83m), 12' (3.66m) and 24' (7.32m) lengths]

are available as an additional accessory.

• To avoid constant unsecured alarms, be sure that the Cable Lock

is closed while it is not being used.

• Inspect the gasket whenever the housing is opened and replace if

worn or damaged. Be sure the gasket is in the proper position

before closing the housing.

• This product is designed for indoor/outdoor use.

Components

A. Gasket F. Tamper

B. Inner housing G. Battery

C. Outer housing H. Screws

D. Cable lock lever I. Replaceable cable

E. Reset button

Product Function

The DS300 Jobsite Security Cable Lock is a 12' (3.66m) cable impreg-

nated with a heavy duty urethane jacket over stainless steel braiding

which provides strength, durability and flexibility. As the cable ends are

disconnected, the system will be notified of an unsecured device.

Once activated, this device will work exclusively with the assigned

DS100 Jobsite Security Portable Alarm System.

1. The DS300 contains a locking mechanism with a location for a

standard padlock (not included) to provide additional security. The

addition of a padlock is recommended.

2. The DS300 features a tamper that notifies the system when the

cover has been opened.

3. The DS300 features 900 MHz spread spectrum communication

with the Base Unit allowing for a range of up to 2000' (610m).

NOTE: Metal objects blocking radio frequency (RF) transmission can

affect the range of the sensor.

Prevention of False Alarms

The majority of alarms that occur are false. These situations happen

every day due to user error, incorrect installation or improper mainte-

nance of the system. False alarms will limit the responsiveness to the

CAUTION: POTENTIAL EQUIPMENT

MALFUNCTION OR FAILURE. Do not

touch the electronic components inside

the device, except the reset button and

battery.

CAUTION: POTENTIAL EQUIPMENT

MALFUNCTION OR FAILURE. If exterior

coating is damaged and the metal is

exposed, the secured equipment could

short out.

FIG. 1

KLFIG. 3

FIG. 2

system, and become a general inconvenience. As the number of

false alarms increases, authorities have become less apt to respond

to alarm systems due to this problem. Many of these situations can be

avoided by following some very simple practices.

• Ensure all users are properly trained on the operation of the

system.

• Always turn off the system with the Key Chain Remote Control

before entering protected area.

• Lock all protected doors, windows or any other asset attached to

a sensor.

• Check that motion detectors are not obstructed. Do not allow

sources of heat or sound in range of the motion or vibration

sensors.

• Check that premises are cleared and assets secured before setting

the system.

• Turn off all noise sources – radios, compressors, generators,

heavy equipment, etc.

• Know how to cancel an alarm or turn off the system before

activating.

• If a false alarm is tripped notify customer service immediately.

• Test the system on a monthly basis to ensure proper functioning

• Check cellular signal, power supply, and that sensors are secured

on a daily basis.

Recommended Locations

• Secure product off the ground [above 3 feet (.91m)] to ensure

better communication with the Base Unit (DS100).

• Recommended for use on mobile equipment, containers, gates

and remote assets.

• Secure assets by wrapping the cable through equipment, tools,

materials or other assets.

• Replacement lengths of 2' (.61m), 6' (1.83m), 12' (3.66m) and

24' (7.32m) lengths are available at additional cost.

Installing & Changing Battery

This wireless sensor requires a non-rechargeable CR-123 3.0 Volt

Lithium battery.

NOTE: The system must be disarmed prior to any changes.

TO INSTALL A BATTERY

1. Remove five screws (H) from the outer housing (C).

2. Separate housings.

3. Install new battery using the polarity (+ and -) markings on the

battery and equipment. Do not use excessive force. If the battery

does not fit, ensure that it matches the polarity markings.

4. Press the reset button (E) on the device. After opening the

device, the Base Unit will display a tamper fault. (see Device

Registration)

TO CLEAR A FAULT

a. Select DISPLAY.

b. Scroll list of fault(s).

c. Select CLEAR.

d. Enter master code.

e. Select OK.

5. Rejoin housings.

6. Reinsert the five screws into the outer housing and tighten.

TO CHANGE THE BATTERY

CAUTION: Never use a damaged or worn out battery.

1. Remove five screws (H) from the outer housing (C).

2. Separate housings.

3. Carefully remove the old, discharged battery. Dispose of the

battery according to local regulations.

4. Install new battery using the polarity (+ and -) markings on the bat-

tery and equipment. Do not use excessive force. If the battery does

not fit, check to make sure that it matches the polarity markings.

5. Press the reset button (E) on the device to restore programming.

After resetting the sensor, replace the outer housing. By opening

the device, the Base Unit may display a tamper fault.

TO CLEAR A FAULT

a. Select DISPLAY.

b. Scroll list of fault(s).

c. Select CLEAR.

d. Enter master code.

e. Select OK.

6. Rejoin housings.

7. Reinsert the five screws into the outer housing and tighten.

Securing Equipment

The DS300 has a cable that is impregnated with a heavy-duty

urethane jacket over stainless steel braiding. As the cable ends are

disconnected, the system will be notified of an unsecured device.

Also, if for any reason the circuit is broken (i.e., cable is cut), the

Cable Lock will be considered unsecured and will send an alarm

notification. The Cable Lock needs to be removed before operating

the attached equipment.

TO SECURE

1. Rotate the cable lock lever (D) counterclockwise 90˚ to open and

wrap cable around equipment.

2. Insert the small cable end (J) as shown in Figure 2.

3. Align the slot (K) on the cable end with the tab (L) on inner

housing (Fig. 3).

4. Rotate the cable lock lever clockwise 90˚ back to its original

position as shown in Figure 1.

NOTE: A padlock (not included) is recommended for additional

security.

TO UNSECURE

1. Rotate the cable lock lever (D) counterclockwise 90˚ to open.

2. Disconnect small cable end (J) and remove cable from equip-

ment.

3. Rotate the cable lock lever clockwise 90˚ back to its original

position.

Replacing/Changing Cable

NOTE: The system must be disarmed prior to any changes.

1. Rotate the cable lock lever (D) counterclockwise 90˚ to open.

2. Remove five screws (H) from the outer housing (C).

3. Separate housings.

4. Push the large end (M) of the cable through the large hole in the

outer housing until all of the cable is through.

5. Insert the small end (J) of the new cable through the large hole in

the case from the inside and feed the cable through until the large

cable end is stopped by the outer housing.

6. Vertically align the rectangular end to fit into the inner case recep-

tacle and pull to tighten.

7. Insert the small cable end into the inner housing, aligning the slot

(K) and tab (L). Rotate the cable lock lever back to its original

position.

8. Rejoin the housings.

9. Reinsert the five screws into the outer housing and tighten.

10. The Cable Lock is ready for use (see Securing Equipment).

Device Registration

To activate the device, it must first be assigned to your DS100 Base

Unit. Refer to the DS100 Jobsite Security Portable Alarm System

Instruction Manual for more details on registering a device during the

initial setup.

NOTE: The system must be disarmed prior to any programming

changes.

1. Press the MAIN MENU button on the keypad of the DS100 Base

Unit.

2. Using the keypad, enter the master code.

3. Use the up and down arrows to scroll through the menu until the

System Settings menu is displayed. Select OK.

4. Use the up and down arrows to scroll through the menu until the

Wireless Device Maintenance menu is displayed. Select OK.

5. Use the up and down arrows to scroll through the menu until the

Add/Replace Device screen is displayed. Select OK.

6. The next available device number will be displayed. Up to 48

sensors can be registered to the system. If there are no slots

available, the screen will display ALL DEVICES IN USE. When

the device number is shown, select OK.

7. Remove screws (H).

8. Separate housings.

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Ikke kategoriseret
Model:	DS312

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DS312 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret DeWalt Manualer

DeWalt DCPS3593 Manual

29 Juli 2025

DeWalt DCPS3452 Manual

29 Juli 2025

DeWalt DCE050 Manual

29 Juli 2025

DeWalt DCPS3455 Manual

29 Juli 2025

DeWalt DCPS3386 Manual

29 Juli 2025

DeWalt DCE710 Manual

29 Juli 2025

DeWalt DCPS3456 Manual

29 Juli 2025

DeWalt DW627 Manual

21 Juli 2025

DeWalt DW626 Manual

20 Juli 2025

DeWalt DE4055 Manual

20 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech MIC-711-OX Manual

30 Juli 2025

Intellinet 713108 Manual

30 Juli 2025

Electro Harmonix EU12AC-1000 Manual

30 Juli 2025

Advantech PCIE-1753 Manual

30 Juli 2025

MXR Rockman X100 Manual

30 Juli 2025

MIPRO MI-909R Manual

30 Juli 2025

Advantech AMAX-4870 Manual

30 Juli 2025

Advantech IDK-1112P-50XGA2 Manual

30 Juli 2025

MIPRO MP-820 Manual

30 Juli 2025

Advantech ARES-12290 Manual

30 Juli 2025