DeWalt DW0732 Manual

DeWalt Ikke kategoriseret DW0732

Læs gratis den danske manual til DeWalt DW0732 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om DeWalt DW0732, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Digital Laser Detector

SAFETY

• Read and understand this instruction sheet before using this

detector and clamp.

• Read and understand the instruction manual for the rotary laser

that you are operating with the detector and clamp.

• Set the laser at a position above or below eye level.

DANGER: DO NOT STARE INTO THE LASER BEAM.

WARNING: This product contains a chemical known to the State

of California to cause cancer, or birth defects or other reproductive

harm.

Introduction

The D WALT Digital Laser Detector can be used with or without theE

enclosed Detector Clamp. Without the clamp, the detector can be

held in place by hand or with the magnets on the top of the unit. The

magnets will hold the detector to steel studs or ceiling track. When

used with the clamp, the detector can be positioned on a grade rod,

leveling pole, stud or post.

Before use, remove and discard the translucent plastic tape that has

been placed on the front and back LCD indicator windows.

The DEWALT Digital Laser Detector enables you to locate a laser

beam emitted by a Rotary Laser in bright light conditions or over

long distances. The detector can be used in both indoor and outdoor

situations where it is difficult to see the laser beam. The detector is

not for use with non-rotating lasers.

The detector gives both visual and audio signals as to the location

of the laser beam. The DEWALT Digital Laser Detector is compati-

ble with most rotary lasers on the market today.

BATTERIES: The Digital Laser Detector is powered by 3 “AAA”

batteries. To install the batteries provided, remove the battery

compartment cover on the back of the detector by rotating the

cover counterclockwise and lifting the cover off. Figure 1 shows

the orientation of the cells in the compartment. A diagram is also

cast into the compartment as a reminder. Replace the compart-

ment cover. Do not over tighten.

When the battery power is running low, a “LOW” indicator will show

in the LCD windows on the front and back. When replacing batter-

ies, do not mix old and new cells.

MOUNTING ON A GRADE ROD

1. To secure your Laser Detector to a Grade Rod first attach the

detector to the clamp as shown in Fig. 2.

2. Press the Quick Release Button on the clamp and pull out the

long threaded screw.

3. Position the Laser Detector at the height needed and tighten the

clamp to the Grade Rod (Fig. 3).

4. To make adjustments in height, slightly loosen the clamp, repo-

sition and retighten.

Operation

• Set up, position and level the rotary laser that you will be using.

Turn the laser on and make sure that the laser is rotating and

emitting a laser beam. This detector has been designedNOTE:

to be used only with a rotating laser. The detector will not work

with a stationary beam laser level.

• Turn the detector on by pressing the ON button. The LCD “Level

Beam Indicator” line will flash on and then off. The detector will

emit a high pitched tone for a second and ON will show in the

display window. Speaker volume is set on “High” at the factory

and may be adjusted to High, Low or Off by pressing the volume

button.

• The volume will cycle from High, to Low, to Off each time the

button is pressed. NOTE: Audio signals will only be emitted

when the rotary laser beam passes over the Beam Detection

window and the volume is set for High or Low.

• To detect the laser beam, position the front side of the detector

toward the rotary laser. Remember: The laser must be rotating.

It will be difficult to see the laser beam. Move the detector up or

down within the approximate area of the beam until you see the

display show “UP” or “DOWN” arrows and you hear the tones.

DW0732 Digital Laser Detector

and Detector Clamp

FIG. 2

FIG. 1

FIG. 3

ON - MARCHE - ENCENDIDO

VOLUME - VOLUME - VOLUMEN

BEAM DETECTION

WINDOW

FENÊTRE DE

DÉTECTION DES

FAISCEAUX

VENTANA DE

DETECCIÓN DEL

RAYO

QUICK RELEASE

BUTTON

BOUTON DE

DÉGAGEMENT

RAPIDE

BOTÓN DE

FIJACIÓN RÁPIDA

LCD

AFFICHAGE ACL

LCD (PANTALLA

DE CRISTAL

LÍQUIDO)

MAGNETS - AIMANTS - IMANES

DEWALT Industrial Tool Co. Inc., 701 E. Joppa Road, Towson, MD 21286 (AUG04) Form# 627150-00 DW0732

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Ikke kategoriseret
Model:	DW0732

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW0732 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret DeWalt Manualer

DeWalt DXCMTB5590856 Manual

16 September 2025

DeWalt DWE46170 Manual

7 September 2025

DeWalt DXV50SPTA Manual

4 September 2025

DeWalt DE0734 Manual

4 September 2025

DeWalt DXV38PRO Manual

3 September 2025

DeWalt DXV53PRO Manual

3 September 2025

3 September 2025

3 September 2025

3 September 2025

3 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Deye SUN-BK60SG01-EU-AM2 Manual

29 Oktober 2025

Miniland 89678 Manual

29 Oktober 2025

CyberPower PS205U Manual

29 Oktober 2025

Wilfa DAPPER 1800 ST2B-200 Manual

29 Oktober 2025

Gigabyte GP-GR26C16S8K1HU408 Manual

29 Oktober 2025

Moen Nio S75005EV2SRS Manual

29 Oktober 2025

ErGear Keyboard Tray Manual

29 Oktober 2025

Abus Secoris BUBE60100 Manual

29 Oktober 2025

Wilfa Zense CG3B-125 Manual

29 Oktober 2025

Eliminator Lighting E 104 Manual

29 Oktober 2025