DeWalt DW7470 Manual


Læs gratis den danske manual til DeWalt DW7470 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om DeWalt DW7470, eller vil du spørge andre brugere om produktet?

Side 1/2
D
FIG. 1
E
F
FIG. 2
WARNING: For your own safety, read the tool instruction manual before using any
accessory. Failure to heed these warnings may result in personal injury and serious
damage to the tool and the accessory. When servicing this tool, use only identical
replacement parts.
WARNING: TURN OFF AND UNPLUG TOOL BEFORE ATTEMPTING TO MOVE
IT, MAKE ANY ADJUSTMENTS, OR REMOVING OR INSTALLING ATTACHMENTS
OR ACCESSORIES.
WARNING: DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools
in damp or wet locations, or expose them to rain. Keep work area well lighted. Always
operate tool in a well-ventilated area free of combustible materials, gasoline or solvent
vapors. If sparks come in contact with flammable vapors, they may ignite, causing fire
or explosion.
CAUTION: NEVER MAKE ANY CROSSCUT UNLESS THE MATERIAL IS POSI-
TIONED FLAT ON THE TABLE AND AGAINST THE MITER GAUGE FENCE.
Personal injury may result.
CAUTION: Never use rip fence as length stop when crosscutting. Unsupported cut-off
piece between blade and rip fence may bind blade and cause personal injury.
Miter Gauge Assembly
STEP 1 Insert telescoping scale (A) into housing (B), shown in Figure 1. Arrange miter
gauge as shown in Figure 2. Align 9mark with end of outer housing. Tighten
clamp (L) as shown in Figure 3.
STEP 2 Loosen thumb screws (D). Attach miter fence (E) to miter gauge (F) by sliding
miter gauge fence slot (G) shown in Figure 2 over fence clamp (P) shown in
Figure 5. Tighten thumb screws (D) to lock fence into place (Fig. 2). To adjust,
loosen thumb screws.
STEP 3 Attach adjustable stop (H) to miter fence. Slide adjustable stop locking hardware
(I) into slot on top of the fence (Fig. 2).
Miter Gauge Use
ADJUST MITER GAUGE ANGLE (FIG. 3)
Loosen thumb screw (L). Align mark on with end of housing (J).telescoping scale (A)
Tighten thumb screw (L).
ANGLE DETENT SYSTEM (FIG. 3)
The miter gauge is equipped with a detent system for easily setting more frequently used
angles.
To Adjust Miter Gauge:
Loosen thumb screw (L). Press and hold detent button (K) on bottom of the housing
(B). Slide the telescoping scale (A) into the housing until the desired detent catches.
Tighten thumb screw (L).
MITER GAUGE CALIBRATION (FIG. 4)
Set the miter gauge to 90˚ using the detent system. Loosen eccentric lock screw (M)
inside the housing using the hex key (N). Turn eccentric (O) to adjust gauge to true 90˚
using calibration square. Tighten eccentric lock screw.
REVERSING MITER GAUGE (FIG. 4, 5)
Loosen thumb screws (D) and remove miter fence (E). Remove fence clamp (P) from
fence base. Slide telescoping scale (A) out of housing (B). Rotate housing and fence base
to opposite side. Slide telescoping scale back into housing and tighten thumb screw (L).
Reinstall fence clamp (P) and miter fence (E). Tighten thumb screw (D).
MITER GAUGE SLIDE ADJUSTMENT (FIG. 4, 5)
If your miter gauge does not fit snugly into the saw table miter gauge slot (C), shown in
Figure 4, three expansion slots are provided to make small adjustments to the width of
the slider (Q), shown in Figure 5.
Turn the set screws (R) clockwise to expand the slot and add tension to the fit of the
slider in the saw table miter gauge slot. Your miter gauge should slide easily in the saw
table miter gauge slot without binding.
A
B
G
H I
J
K
L
O
N
D
F
P
FIG. 3
FIG. 4
FIG. 5
Q
R
R
DW7470 Miter Gauge
DW7470 Jauge à onglets
DW7470 Gramil de inglete
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (DEC03) Form No. 622154-00 DW7470 Copyright © 2003
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of the tool.
M
A
L
C
A
B
E
B


Produkt Specifikationer

Mærke: DeWalt
Kategori: Ikke kategoriseret
Model: DW7470

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW7470 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret DeWalt Manualer

DeWalt

DeWalt DXCM009-0369 Manual

26 November 2025
DeWalt

DeWalt DCS374 Manual

30 Oktober 2025
DeWalt

DeWalt DWST83471 Manual

30 Oktober 2025
DeWalt

DeWalt DXCMTB5590856 Manual

16 September 2025
DeWalt

DeWalt DWE46170 Manual

7 September 2025
DeWalt

DeWalt DXV50SPTA Manual

4 September 2025
DeWalt

DeWalt DE0734 Manual

4 September 2025
DeWalt

DeWalt DXV38PRO Manual

3 September 2025
DeWalt

DeWalt DXV53PRO Manual

3 September 2025
DeWalt

DeWalt DCR009 Manual

3 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone

Waterstone 7800 Manual

11 December 2025
Kwikset

Kwikset 258 Manual

11 December 2025
Schlage

Schlage F170 Manual

11 December 2025
Moen

Moen Align 7565EV Manual

11 December 2025
ALNO

ALNO MC10244 Manual

11 December 2025
JET

JET TAK-ZX Manual

11 December 2025
Waterstone

Waterstone 1455 Manual

11 December 2025
Laica

Laica NE2015 Manual

11 December 2025