DeWalt DWE43144N Manual

DeWalt Kværn DWE43144N

Læs gratis den danske manual til DeWalt DWE43144N (4 sider) i kategorien Kværn. Denne vejledning er vurderet som hjælpsom af 61 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 31 anmeldelser. Har du et spørgsmål om DeWalt DWE43144N, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ENGLISH

Lanyard Attachment Point Installation

To be used with DWE4222N, DWE43066N,

DWE43114N, DWE43115N, DWE43144N, DWE46144N,

DWE46166N Grinders

WARNING: The lanyard attachment point 1 may

only be added to certain models and must be installed

by an authorized service center.

WARNING: For your own safety, read the grinder

instruction manual before using any accessory. Failure

to heed these warnings may result in personal injury

and serious damage to the vacuum and the accessory.

WARNING: Retain this document with the tool

instruction manual for futurereference.

Lanyard Attachment Point (Fig. B)

Safety Warnings Specific for Use At Height

• If the tool is dropped for any reason, the lanyard

attachment point 1 must be inspected and properly

serviced prior to re-use. The lanyard attachment point

is designed to stretch to absorb the shock of a drop. Any

permanent stretch to the device exposing the red marked

internal coils indicates it has been compromised and must

be serviced prior toreuse.

• Always keep the tool and accessories tethered when

working "at height". (Maximum lanyard length: 6.5 ft

[2m])

• Use only with lanyards appropriate for this tool type and

rated for at least 6 lbs (2.72 Kg).

• Crush, cut or entanglement hazard. Do not use near

moving parts, mechanisms or runningmachinery.

• Do not anchor the tool lanyard to anything on your body.

Anchor to a rigid structure that can withstand the forces

of a droppedtool.

• Make sure the lanyard is properly secure at each end prior

touse.

• Inspect tool and lanyard before each use for damage and

proper function (including fabric and stitching). Do not

use if damaged or not functioningproperly.

• Do not alter the lanyard attachment point or use in a

manner other than as instructed in thismanual.

• Only attach tool to a lanyard with a locking carabiner. Do

not attach by looping or knotting the lanyard. Do not use

rope orcord.

• Electrical shock hazard. Be sure power is off when working

in high voltage areas. Some lanyards areconductive.

• Dropped tools will swing on the lanyard, which could

cause injury or loss ofbalance.

• Do not carry the tool by lanyard attachment point or

thelanyard.

• Do not attach more than one tool to eachlanyard.

final page size: 8.5 x 5.5 inches

• Only use appropriate

D WALTe

brand lanyard attachment

point. attachmentpoints NEVER modify tools to create .

• Only transfer the tool between hands while properly

balanced in a stableorientation.

• Do not attach lanyards to tool in a way that keeps guards,

switches or lock-offs from operatingproperly.

• Avoid getting tangled in thelanyard.

• Keep lanyard away from the cutting area of thetool.

• Do not use lanyards or attachment devices to get

additional leverage from thetool.

• Do not use for personal fallprotection.

• Falling object hazard! Only change accessories and

attachments where a dropped object won't cause

a hazard below you. Consult your Authority Having

Jurisdication (AHJ) or site supervisor for procedures for

working atheight.

• Use multi-action and screw gate type carabiners. Do not

use single action spring clipcarabiners.

The lanyard attachment point 1 is intended for use by

competent personnel, who are trained and knowledgeable

regarding working with tools in and around machinery and

"at height".

Installation

DWE43115N, DWE43066N, DWE46166N (Fig. A, B)

1. Position the loops of the lanyard attachment point on

each side of the tool housing.

2. Slide provided bolt through first washer, both loops and

the housing. Install second washer and nut onto bolt

and tighten securely.

IMPORTANT: Always use manual, torque-calibrated

screwdrivers and tighten to

15.9–18.6inlbs (1.8–2.1Nm). Do not use pneumatic or

electric screwdrivers.

DWE4222N, DWE43114N, DWE43144N, DWE46144N

(Fig. C, D)

1. Slide the metal bars of the lanyard attachment point

1 into the slots at the rear of the tool housing, making

note which has the threads.

2. Insert the screw into the housing side without the

threaded bar and feed it through until it engages the

threads of the other bar. Tighten the screw securely.

IMPORTANT: Always use manual, torque-calibrated

screwdrivers and tighten to 15.9–18.6inlbs (1.8–

2.1Nm). Do not use pneumatic or electric screwdrivers.

For more information, please contact

D WALTe

at the

address below or 1-800-4-

D WALTe

(1-800-433-9258).

FRANCAIS

Installation du point de fixation des

longes

À utiliser avec les meuleuses DWE4222N,

DWE43066N, DWE43114N, DWE43115N, DWE43144N,

DWE46144N, DWE46166N

AVERTISSEMENT: le point de fixation des longes

de sécurité 1 peut seulement être ajouté à certains

modèles et doit être installé par un centre de services

autorisé.

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Kværn
Model:	DWE43144N

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DWE43144N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kværn DeWalt Manualer

DeWalt DWE46125 Manual

8 September 2025

DeWalt DWE46101 Manual

6 September 2025

DeWalt DWE4367 Manual

3 September 2025

DeWalt DW755 Manual

1 September 2025

DeWalt DW820 Manual

1 September 2025

DeWalt DW450 Manual

1 September 2025

DeWalt DWEN202 Manual

1 September 2025

DeWalt D28886 Manual

1 September 2025

DeWalt DW753 Manual

31 August 2025

DeWalt DWE4016 Manual

31 August 2025

Kværn Manualer

Nyeste Kværn Manualer

Bosch HWS 88/230 Industrial Manual

27 December 2025

Bosch HWS 810/300 Industrial Manual

23 December 2025

Scheppach BC-AG125-X Manual

19 December 2025

Milwaukee M18 2680-20 Manual

15 December 2025

Milwaukee M18 2686-20 Manual

9 December 2025

Bosch GWS 14-50 PBD Professional Manual

9 December 2025

Bosch GWS 10-450 Professional Manual

9 December 2025

Bosch GWX14-60PBD Professional Manual

9 December 2025

JET JAT-482 Manual

9 December 2025

JET JAT-411 Manual

9 December 2025