Dimplex FX20V Manual

Dimplex Varmeapparat FX20V

Læs gratis den danske manual til Dimplex FX20V (3 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Dimplex FX20V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3



Contact Details



Pleasenotethat some contact ofthe details on 

thisPDFdocumentmaynotbe current.



Pleaseuse  the following detailsifyouneedto

contactus:



Telephone:0844 879 3588

Email:customer.services@gdcgroup.co.uk



The widecustomer alsosupportsection websiteofour  features a

rangeof ofinformationwhichmaybe use availabletoyouandis 

24 ahours day.Itincludes:



• Operating   and installation instructions

• Easy       ‘How to use’ guides for storage heaters

• Service  and repairs

• Wheretobuyourproducts

• Literature downloads

• Heating  requirement calculator



 ‐Visit www.dimplex.co.uk/support

A division of GDC Group Ltd

Millbrook House Grange Drive Hedge End Southampton SO30 2DF

www.dimplex.co.uk

istered No: 1313016 En

land

VAT GB 287 1315 50004

EEE Producer Registration Number –

WEE/GE0057TS

Paper from sustainable sources

Downflow Fan Heater

Model : FX 20V

Installation and Operating Instructions

Dimensions

(millimetres)

Model(s) Specification

FX 20V (High Level) 1/2kw + Adjustable Thermostat (internal by installer)

Fig. 1

(IP22)

IMPORTANT SAFETY

ADVICE

WARNING - DO NOT USE THIS HEA

TER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR

A SWIMMING POOL.

DO NOT COVER THE APPLIANCE or place material or garments

on it, or obstruct the air circulation around this appliance, for

example with curtains or furniture, as this could cause

overheating and a fire risk.

DO NOT PLACE AEROSOLS OR OTHER CONTAINERS

SUSCEPTIBLE TO HEAT IN THE DIRECT AIRFLOW FROM THE UNIT.

THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A

FIXED SOCKET OUTLET.

WARNING: Do not operate the heater with the top cover removed.

The appliance is not intended for use by children or other persons

without assistance or supervision if their physical, sensory or

mental capabilities prevent them from using it safely. Children

should be supervised to ensure that they do not play with the

appliance.

WARNING – DISCONNECT THE HEATER FROM THE ELECTRICITY

SUPPLY BEFORE UNDERTAKING SERVICE OR REPAIR.

WARNING – If the appliance is fitted in a bathroom, a cable outlet

will be necessary with the supply to the unit controlled by a

double pole switch. The switch if inside the bathroom should be

pull cord operated and if outside should be adjacent to the

entrance door. The appliance must be mounted so that no part of

it can be touched by any person using bath or shower.

THIS HEATER MUST NOT BE OPERATED WITHOUT THE COVER

CORRECTLY IN POSITION.

Warning : In order to avoid a hazard due to inadvertent resetting of

the thermal cutout, this appliance must not be supplied through an

external switching device, such as a timer, or connected to a

circuit that is regularly switched on and off by the utility.

General

The heater has a loading of 2KW. It is designed for permanent wall mounting

and is suitable for operation on A.C. electricity supply having the same

voltage as shown on the rating label.

The heater is fitted with an internally mounted selector switch which on

installation of the heater allows a choice of 1kW or 2kW output to suit the

dimensions of the room to be heated.

In rooms of less than 9 – 11 cubic m. (350 - 400 cubic ft.) 1kW output should

be selected, otherwise nuisance tripping of the thermal overload cut-out

may occur.

NOTE : THE SWITCH HAS BEEN FACTORY SET FOR 1kW OPERATION.

IF ADDITIONAL OUTPUT IS REQUIRED, 2kW CAN BE SELECTED ON

INSTALLATION.

SUPPLY CABLE IS NOT SUPPLIED WITH THIS APPLIANCE AND IT

SHOULD THEREFORE BE INSTALLED BY A COMPETENT ELECTRICIAN

IN ACCORDANCE WITH THE LATEST IEE REGULATIONS.

08/15981/6 Issue 6

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Controls

The cut-out is a safety device which switches off the heater and fan if for

any reason the appliance overheats - see ‘Safety’.

The thermal fuse link is provided as an added safety feature, and operates

to open circuit if there is abnormal overheating within the appliance. The

operation of these safety devices is described under ‘Safety’.

The pull cord switch operates the ON/OFF switch. (An indicator light

illuminates to show when the heater is ON and does not illuminate when

the heater is OFF) .

The heater is fitted with an adjustable thermostat, which has three different

settings : 1. - Low, 2. - Medium, 3 - High. This gives you an approximate

room temperature range of 18°C - 32°C depending on room size. If internal

switch is set to 2kW, the temperature switches to half heat when the room

warms up. Full heat will be switched on automatically when the room

temperature falls. This can be adjusted by installer, by removing top cover.

The thermostat will only function when 2KW is selected. The thermostat

has been factory set on ‘2’ (Medium).

To adjust the thermostat setting or reset selector switch first remove the top

cover, then adjust thermost

at to required setting, or reset selector switch to

1kW or 2kW as required, then refit top cover. Do not operate the unit with

the top cover removed.

Safety

Cut-Out

For your safety, this appliance is fitted with a thermal cut-out. In the event

that the product overheats, the cut-out switches the heater off automatically.

To bring the heater back into operation, remove the cause of overheating,

then turn off the electrical supply to the heater for a few minutes.

When the heater has cooled sufficiently reconnect and switch on the heater.

Fuse Link

A thermal fuse link is provided as an added safety feature. If the fuse link

operates and opens circuit it is the result of abnormal overheating within

the appliance, and servicing of the appliance by a competent service

engineer will be required in order to ensure the future safe operation of the

heater. Dimplex Customer Services should be contacted (see “After Sales

Service” for details), who will arrange the replacement of any faulty parts

and the fitting of a new fuse link.

Installation

WARNING: Minimum clearences must be adhered to when mounting

the heater.

Before undertaking installation work, ensure the electricity supply is

disconnected from any relevant fixed wiring. Supply cable is not supplied

with this appliance and it should therefore be installed by a competent

electrician in accordance with the latest IEE wiring regulations.

The supply circuit must be adequate for the input of the appliance and

must be protected with a 13A fuse.

A suitable termination to the fixed wiring of the premises must be provided

adjacent to the final position of the appliance through a double pole

switch having a contact separation of at least 3mm in all poles.

250 229

242

109300

MIN

1800

600

MIN

floor

ceiling

shelf

Produkt Specifikationer

Mærke:	Dimplex
Kategori:	Varmeapparat
Model:	FX20V
Type:	Radiator/ventilator
Tænd-/slukkontakt:	Ja
Justerbar termostat:	Ingen
Varmeevne:	2000 W
Bredde:	229 mm
Dybde:	109 mm
Højde:	242 mm
Vægt:	1100 g
Velegnet til:	Indendørs
Placeringsmuligheder:	Væg
Produktfarve:	Hvid
Strøm:	2000 W
Indikatorlampe:	Ja
Kan monteres på væggen:	Ja
Varmekilde:	Elektrisk
Velegnet til badeværelse:	Ja