Dimplex PLX1500NC Manual

Dimplex Varmeapparat PLX1500NC

Læs gratis den danske manual til Dimplex PLX1500NC (4 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Dimplex PLX1500NC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Installation and Operating Instructions

INDPUKP5RG Issue 6

PLX Panel Convector Heaters

Dimensions

(millimetres)

Model s( )

PLX 500/NC/TI 500 450 108 116

PLX 750/NC/TI 750 620 108 286

PLX 1000/NC/TI 1000 620 108 286

PLX 1250/NC/TI 1250 688 108 354

PLX 1500/NC/TI 1500 688 108 354

PLX 2000/NC/TI/TX 2000 860 108 526

PLX 3000/TI/TX 3000 860 143 526

Important Safety Advice

When using electrical appliances, basic

precautions should always be followed to

reduce the risk of re, electrical shock, and

injury to persons, including the following:

IMPORTANT – The wall bracket supplied with

the appliance must be used.

WARNING – Do not use this heater in the

immediate surroundings of a bath, a shower

or a swimming pool.

IMPORTANT – If the heater is installed in a

room containing a bath or shower, it must be

so installed that switches and other controls

cannot be touched by a person using a bath

or shower.

Do not use outdoors.

Do not locate the heater immediately below a

xed socket outlet or connection box.

WARNING: In order to avoid overheating, do

not cover the heater. Do not place material

or garments on the heater, or obstruct the

air circulation around the heater, for instance

by curtains or furniture, as this could cause

overheating and a re risk.

NEVER cover or obstruct in any way the heat

outlet slots at the top of the heater or the air

inlet slots in the base of the heater.

The heater carries the Warning symbol

indicating that it must not be covered.

CAUTION - Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present.

This appliance can be used by children aged

from 8 years and above and by persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given supervision

or instruction concerning use of the appliance

in a safe way and understand the hazards

involved.

Fig. 1

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Watt A B X

150

MIN

150

MIN

150

MIN

430

119 215

310

150

150 min

255

Children shall not play with the appliance.

Cleaning and user maintainance shall not be

made by children without supervision.

Children of less than 3 years should be kept

away unless continuously supervised.

Children aged from 3 years and less than 8

years shall only switch on/off the appliance

provided that it has been placed or installed

in its intended normal operating position and

they have been given supervision or instruction

concerning use of the appliance in a safe

way and understand the hazards involved.

Children aged from 3 years and less than 8

years shall not plug in, regulate and clean the

appliance or perform user maintainance.

Note that due care and consideration must be

taken when using this heater in series with a

thermal control, a program controller, a timer

or any other device that switches on the heat

automatically, since a re risk exists when the

heater is accidentally covered or displaced.

If the supply cord is damaged it must be

replaced by the manufacturer or service agent

or a similarly qualied person in order to avoid

a hazard.

WARNING: Servicing and product

repairs should only be undertaken by the

manufacturers approved service agent or a

similarly qualied person, using only exact

manufacturer approved spare parts.

IMPORTANT – The supply circuit to the heater

must incorporate a double pole isolating switch

having a contact separation of at least 3mm.

WARNING: PLX****NC heaters are not

equipped with a device to control the room

temperature. Do not use these heater in small

rooms when they are occupied by persons

not capable of leaving the room on their own,

unless constant supervision is provided.

Access to the controls

The controls cover (see ‘x’ in Fig. 1) on your heater has a

latch which may be locked shut if desired using a small bladed

screwdriver - see .Fig. 3

To open the cover insert the blade of the screwdriver in the

small slot and rotate a quarter of a turn clockwise to disengage

the latch. The cover may then be hinged back towards the wall

for access to the controls.

Operation - Thermostat only models

Control of Output and Temperature Fig. 4(see )

The switch marked and controls the electricity supply to the O I

heating elements. The OFF position is marked .O

The switch marked - (half heat – full heat) provides a I II

choice of output as desired.

Thermostat Operation

The heater is tted with an adjustable thermostat enabling

the room temperature to be controlled by adjusting the setting

accordingly. The * setting represents a room temperature of

approximately 5°C and may be used for protection against

frost. Higher temperature settings range from 1-6 (max.)

creating a room temperature of approximately 30°C.

A neon indicator light glows when the appliance is actually

heating.

Switch on the heater and turn the thermostat knob to mark

6 opposite the indicator mark (located on centre right of the

knob - see & ), and set selector switch to full heat Fig. 4 5

output to warm the room rapidly. When the room temperature

has reached the desired level, turn the thermostat knob back

slowly until the thermostat just clicks off. The heater will then

maintain the room temperature at the chosen level, provided

that the correct size of heater has been selected for the room

to be heated.

NOTE – Should your heater fail to come on when the

thermostat knob is at a low setting, this may be due to the

room temperature being higher than the thermostat setting.

General

NOTE: The PLX Convector is designed for wall mounting on

the wall brackets supplied. The wall brackets supplied with the

appliance must be used. It should only be operated when in

the upright position as shown.

All models are splashproof to IP24 standard.

Models PLX…TI are tted with a 24 hour programmable timer.

Models PLX…TX are tted with a 7 day programmable timer.

Models PLX…NC are tted with no controls, for use with

external thermostatic or programming controllers.

Before connecting the heater check that the supply voltage is

the same as that stated on the heater.

Please note that lit cigarettes, candles and oil burners,

combined with the convection effect of electric heaters

can cause soot deposits to build up on the surface directly

above and to the sides of the heater. This is not the fault

of the heater. Extensive burning of candles or smoking

in the operating environment of this product can produce

heavy discoloration within a few months of use.

Wall Mounting

IMPORTANT – The wall brackets supplied with the appliance

must be used. The heater should be positioned observing

the minimum clearances stated around the heater - see

Fig. 1.

DO NOT locate the heater immediately below a xed socket

outlet or connection box.

1. Remove wall mounting bracket from the back of

the heater by depressing the spring latch at the top

of each bracket - see .Fig. 2

2. Fix the wall bracket securely to the wall through the

four screw holes provided.

3. Present the heater to the wall bracket, and engage

lower slots in the back with bracket.

4. Raise the heater to upright position and push the

heater onto brackets to engage top latch.

Fig. 3

Fig. 4

Fig. 2

255

MIN

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent

electrician, and be in strict accordance with the current I.E.E.

regulations for Electrical Equipment in Buildings.

The heater is tted with a length of exible cable type H05VV-F

size 3 x 1.0mm2 on models PLX 500 - 2000 and size 3 x 1.5mm

on PLX 3000 models, for connection to the xed wiring of

the premises through a suitable connection box positioned

adjacent to the heater.

The supply circuit to the heater must incorporate a double pole

isolating switch having a contact separation of at least 3mm.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing

conductor in the supply cord is deemed to provide the

supplementary bonding connection (see Regulation 544.2.5,

17th Edition I.E.E. Wiring Regulations).

Produkt Specifikationer

Mærke:	Dimplex
Kategori:	Varmeapparat
Model:	PLX1500NC

Har du brug for hjælp?

Hvis du har brug for hjælp til Dimplex PLX1500NC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Dimplex Manualer

Dimplex H 260E Manual

12 August 2025

Dimplex BY 802 S Manual

12 August 2025

Dimplex DHCHR16M Manual

15 Juli 2025

Dimplex DHOC15 Manual

15 Juli 2025

Dimplex DX 512E Manual

5 Juli 2025

Dimplex VFE 60 Manual

5 Juli 2025

Dimplex RCE 150 Manual

5 Juli 2025

Dimplex DTD2T 07 Manual

5 Juli 2025

Dimplex VFE 40 Manual

4 Juli 2025

Dimplex MH 15 PAM Manual

4 Juli 2025

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

Plus More PBAEA001 Manual

13 August 2025

Eurolite LED THA-120PC Manual

13 August 2025

Thermastore Heatwave270 Manual

13 August 2025

Camry CR 7827 Manual

13 August 2025

DeLonghi Dragon 4 Pro TRDX40615E Manual

12 August 2025

Rheem 52D300 Manual

12 August 2025

DeLonghi Dragon 4 Pro TRDX41024E Manual

12 August 2025

Tesy CN 055 250 MIS F Manual

12 August 2025

Adler AD 6815 Manual

12 August 2025

Adler AD 7748 Manual

12 August 2025