Dormakaba RCI 4 Manual

Dormakaba Ikke kategoriseret RCI 4

Læs gratis den danske manual til Dormakaba RCI 4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Dormakaba RCI 4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION

RCI 4/7 SERIES

ELECTRIC STRIKES

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.comIS47A

PCN18041

R03-19TG

A 1-1/4 1.250 31.75

B 4-7/8 4.875 123.83

C 3-3/8 3.375 85.73

D 7/8 .875 22.23

E 3/8 .375 9.53

F 1/8* .125* 3.18*

G 1-11/16 1.688 42.86

R 5/32 .156 3.97

K 4-1/8 4.125 104.78

M 12-24 — —

RCI 7104, 7304 Aluminum Frames, 1-1/2” D

RCI 4104, 4304 Aluminum Frames, 1-1/2” D

Any modular or A41 A43 A71, , A73

with B4704 faceplate

MEASUREMENT

FRACTIONAL

INCHES

DECIMAL

INCHES

METRIC

Vertical Centerline

of Door**

RCI 7105, 7305 Aluminum & Wood Frames, 1-1/2” D

RCI 4105, 4305 Aluminum & Wood Frames, 1-1/2” D

Any modular or A41 A43 A71, , A73

with B4705 faceplate

MEASUREMENT

FRACTIONAL

INCHES

DECIMAL

INCHES

METRIC

A 1-1/8 1.125 28.58

B 5-7/8 5.875 149.23

C 3-3/8 3.375 85.73

D 7/8 .875 22.23

E 1/4 .250 6.35

F 1/8* .125* 3.18*

G 1-11/16 1.687 42.86

R 5/32 .156 3.97

K 5-3/8 5.375 136.53

M 12-24† — —

1. Determine the vertical centerline of the door lock face and

the horizontal centerline of the latch.

IMPORTANT: When determining the horizontal centerline

observe the following:

FOR MORTISE LOCKS: Align the angled ramps of the lip

bracket with the deadlock trigger of the mortise latch.

FOR CYLINDRICAL LOCKS: Align the center of the latch with

the center of the strike opening.**

2. Transfer both the horizontal and vertical centerlines to the

doorframe.**

3. Prepare the doorframe for cutting as per the appropriate

drawing.

4. If required, install “no weld” mounting brackets as per the

instructions on page 3.

5. Attach the strike insert (coil unit or “motor”) to the

lip bracket with the small machine screws provided.

(M4 x 9.5mm)

6. Attach the strike faceplate to the lip bracket with machine

screws (M4 x 9.5mm) provided. (It may be desirable to leave

these screws slightly loose to facilitate insertion into the

doorframe.)

7. Connect the incoming wiring from the power supply to the

terminal screws on the strike insert. RCI door strikes are

not polarity sensitive although be certain to observe proper

polarity if a suppression diode is required for access control

applications.

8. Install the door strike in the doorframe using the screws

provided.

Instructions

NOTE: Specifications subject to change without notice.

* Dimension F is measured from face of mounting tab to face of frame.

** Dimension X on the drawing is determined by the vertical centerline of the door. If the latch incorporates a deadlocking pin additional steps will be