Dormakaba RCI 8310 Manual

Dormakaba Ikke kategoriseret RCI 8310

Læs gratis den danske manual til Dormakaba RCI 8310 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Dormakaba RCI 8310, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

INSTALLATION

RCI 8310 / 8320

ELECTROMAGNETIC LOCKS

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

IS8310-20-V1-2

PCN19025

R07-20GR-1

1. Mount the electromagnetic lock to the door frame as outlined on

the installation template included with the product.

NOTE: During installation of the armature plate to the door it

is essential that the armature plate remains movable. The

armature plate must be allowed to pivot on the center-mounting

bolt to allow proper alignment with the magnet surface. If the

plate is not aligned with the magnet surface, the lock may lose

holding force or not lock at all .

The head of the armature mounting bolt ships with a rubber

washer affixed to it. This washer should project slightly beyond

the surface of the armature plate. This is to allow the washer to

expand when power is removed and break the air vacuum

between the plate and the magnet surface. If this washer is

removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided for

the armature plate bolt and the four captive electromagnetic lock

mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware

to disengage and fall, causing serious bodily injury and property

damage. dormakaba Canada Inc. and/or dormakaba USA Inc. will

not be liable to the installer, purchaser, end user or anyone else for

damage or injury to person or property due to improper installation,

care, storage, handling, maintenance, inspection, abuse, misuse

or act of God or nature involving this product or any related

accessories or parts.

2. Route the power supply connecting wire through the door frame

and into the wire access hole in the top of the magnet housing.

Connecting wire should be of sufficient gauge for the lock being

installed and the distance being run.

Installation Instructions

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Pre-Installation Instructions

1. This product must be installed according to all applicable building

and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally sound

prior to installation of the electromagnetic lock. The structural

integrity of the mounting surfaces must be strong enough to meet

or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of applications

and different door frame configurations, an experienced installer

with knowledge of this product must make a determination of the

optimal mounting method for this specific application.

7. The components, hardware, installation instructions and mounting

template included with this product are intended for use on

outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories, must be used in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 5 & 6 Product Accessories Guide, for further

information. Accessories may impact holding force.

11. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

3. Once wiring has been routed into the lock cavity, connect wire to

terminal blocks as shown in Fig. 1. If optional SCS and/or DSS

features are being used these can also be wired at this time as

shown in Fig. 1.

4. Delayed Relock Feature - Should the built-in delayed relock feature be

required for the installation, a Normally Open Momentary switch such

as an RCI 909 will need to be installed and connected to the two blue

wires from on the circuit board as illustrated in Fig.1. EXIT

The delayed relock feature can be used to momentarily release the

lock and keep it unlocked for a time period from 0 to approximately

35 seconds. The time delay for this feature can be adjusted by

carefully turning the potentiometer (R ) in a counterclockwise W1

direction to increase delay time. Factory setting is zero seconds.

NOTE: On the 8320 double-door model turn bothRCI

potentiometers counterclockwise to increase the relock delay.

If the delayed relock feature is not required the blue wires may be

unplugged from the circuit board @ EXIT.

W1NOTE: If R is not set to zero seconds, the lock will enter

delayed relock mode each time power is applied even if EXIT has

been removed.

To Ensure Instant Release - All switching devices must be wired in

between the DC power source and the positive terminal of the lock in

Fig 2.

Switching the negative power supply line will not allow the lock to

release immediately. RCI electromagnetic locks contain MOV’s for

surge suppression and do not require any additional suppression to be

added during installation. The installation of diodes across the lock input

terminals will cause a delay in release.

Fig. 2 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Fig.1 – Lock Wiring

Delayed Relock Adjustmen RW1t

Turn counterclockwise o incr se delay t ea

on 8310 single and both sides of the 8320

double door model.

Lo Power from ack

f ter r lated DCil ed and egu

power su lypp

Opti al SCS nsoron Se

SPDT Out c tacts ratedput on

for maximum 1A @2 DC4V

EXIT EXIT

Two 8 Loc o rel se o ther using310 ks t ea t ge

t lay relock ture.he de ed fea

Blue Wires

Momentary Switch

Bo de 832 Loth si s o an f 0 ck to release together

usi he lay relock f ture.ng t de ed ea

Le circuit boardft Right circui boardt

Optional Del d Relock W ngaye iri

Single lock o release using t

t lay relock ture.he de ed fea

RED - No a y Closedrm ll

GREEN - Normally O npe

BLACK - Common

Opti l DSS r s tch c tacts rat atona eed wi on ed

0.20A@ DC a 0.12A @ 2 DC12V nd 4V

Blue/White

Wires

Blue Wires

Blue/White

Wires

EXIT EXIT

Momentary Switch

N/O

EXIT

Momentary Switch

Blue Wires

Blue/White

Wires

N/O

Blue Wires

Blue/White

Wires

Blue Wires

Blue/White

Wires

EXIT

8310 V1.2 PCB

MAG

Common

No ally Closedrm

No ally Openrm

Comm Gro don un

VDC Input

Both the SCS and DSS options are shown with Door Open

SCS1 LED

* NOTE: Models with SCS ship with the low voltage

detection circuit ENABLED (jumper LP_EN on 1 pin only).

To DISABLE low voltage detection, place jumper on both

pins of LP_EN.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 8310

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 8310 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Dormakaba 9800 Manual

21 August 2024

Dormakaba HSW-GP Manual

21 August 2024

Dormakaba DKX-10 Manual

21 August 2024

Dormakaba Confidant RFID Kit 1 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025

Daewoo AVS1369 Manual

13 September 2025

SolarEdge SE120K-RW08IBNQ4 Manual

13 September 2025

Varta Fast Wireless Charger 57912 Manual

13 September 2025

Hauppauge Colossus Manual

13 September 2025

Contour Wireless Unimouse Manual

13 September 2025