Draper 31264 Manual

Draper Ikke kategoriseret 31264

Læs gratis den danske manual til Draper 31264 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Draper 31264, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

31264

230V TO 110V

PORTABLE SITE

TRANSFORMER

Original Instructions

Version 2 – February 2023

Read this manual in full before using this product and retain it

for future use. Always use the latest version of the manual.

Please visit for the latest version.drapertools.com/manuals

1. Intended Use

This product converts 230V electrical supplies to a 110V output.

It can be used intermittently for loads up to the rated value or

continuously at 60% of its maximum load, and is centre-tapped

to earth.

2. Specication

Stock No. 31264

Part No. DPT3300/2B

Input voltage: 220–240V AC

Input frequency: 50Hz

Output voltage: 110V

Output amperage: 16A

Rated output:

Intermittent: 3.3kVA

Continuous:

1.98kVA (approx. 60% of

rated intermittent output)

Duty cycle for intermittent use: 5 mins on, 15 mins o

Power factor: 0.93 lag

Impedance voltage: 5.6%

Insulation: Class A

Max. ambient temperature: 20°C

No. of output sockets: 2

Power cable length: 2m

IP rating: IP44

Net weight: 16.5kg (approx.)

3. Health and Safety Information

• Check the product and power cables for signs of damage and

disrepair before use.EVERY

WARNING!

DO NOT use the product if it is damaged

in any way.

• use this product in environments where ammable DO NOT

or explosive substances are present.

• ALWAYS ensure that this product is compatible with the

intended power supply; it is intended ONLY for connection to

domestic power supplies rated at 230V AC.

• This is a Class I appliance: there be an earth MUST

connection in the power supply.

• ALWAYS ensure that this product is compatible with the

appliances to be connected; it is ONLY intended to supply

110V AC power.

• DO NOT connect an extension cord to the 230V power

supply; extensions cords may ONLY be used with the 110V

outputs and must exceed 50m in length.NOT

• If the external exible cable or cord of this transformer is

damaged, it shall be replaced by the manufacturer or his

service agent or a similar qualied person in order to avoid

a hazard.

• DO NOT pull or carry the product by the power cable or use

the cable to remove the plug from a socket.

WARNING!

This product becomes very hot during use.

DO NOT touch or cover the product during or

immediately after use and allow the product to cool

thoroughly before handling or storing it.

• Use this product ONLY on heat-resistant surfaces.

• Keep this product out of reach of children.

• DO NOT expose this product to liquids, wet environments

or frost.

• NEVER exceed the maximum load of the product.

• ALWAYS operate, transport and store this product in an

upright position.

4. Use Modes

The transformer can accommodate dierent loads according to

the way in which it is used:

• When used intermittently for short periods, a load of up to

the maximum rated power may be applied to the transformer.

Important: NEVER exceed the maximum rated load of

the product.

Important: When used intermittently, the product be MUST

allowed to rest for minutes after every minutes of use.15 ve

• When used continuously, a load of up to 60% of the

maximum rated power may be applied to the transformer.

Important: Continuous use is intended for low-wattage

appliances ONLY. Continuous use to power higher-wattage

appliances will overload the product and may cause

signicant damage to the circuitry.

5. Thermal Cut-Out

The transformer is equipped with a thermal cut-out to prevent it

from overheating. If the thermal cut-out is tripped, switch o

and disconnect all appliances and allow the transformer to cool

before gently pressing the reset button.

If the thermal cut-out trips frequently, contact Draper Tools

for support.

6. Disposal

At the end of its working life, dispose of the product responsibly

and in line with local regulations. Recycle where possible.

• DO NOT dispose of this product with domestic waste; most

local authorities provide appropriate recycling facilities.

• DO NOT incinerate this product.as this may release toxic or

corrosive substances.

7. Warranty

Draper Tools products are carefully tested and inspected before

shipment and are guaranteed to be free from defective materials

and workmanship.

Should the tool develop a fault, return the complete tool to

your nearest distributor or contact Draper Tools directly.

Contact information can be found at the back of this manual.

Proof of purchase must be provided.

If, upon inspection, it is found that the fault occurring is due to

defective materials or workmanship, repairs will be carried out

free of charge. This warranty period covers parts and labour for

12 months from the date of purchase. Where tools have been

hired out, the warranty period covers 90 days from the date

of purchase.

This warranty does not apply to any consumable parts,

batteries or normal wear and tear, nor does it cover any damage

caused by misuse, careless or unsafe handling, alterations,

accidents, or repairs attempted or made by any personnel other

than the authorised Draper Tools repair agent.

In all cases, to make a claim for faulty workmanship or materials

within the standard warranty period, please contact or return

the product to the place of purchase. Proof of purchase may

be required.

8. Explanation of Symbols

Helpline: +44 (0) 23 8049 4344 Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 Website: drapertools.com Email: sales@drapertools.com

Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire,

SO53 1YF, UK

Delta International, Delta International BV, Oude Graaf 8, 6002 NL, Weert,

Netherlands.

Read the instruction manual

WARNING!

Do not incinerate or throw onto re

Do not expose to heat or open ames

Two-winding transformer with

functional earthing

No. of output sockets

3.3