DS18 PU210A Manual


Læs gratis den danske manual til DS18 PU210A (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2 anmeldelser. Har du et spørgsmål om DS18 PU210A, eller vil du spørge andre brugere om produktet?

Side 1/8
ENGLISH | ESPAÑOL
PU210A
OWNER'S MANUAL
MANUAL DE USUARIO
BLACK CARPET
ALFOMBRA NEGRA
CAJA PLANA DE SUBWOOFER
ACTIVO DE 10" CON SUBWOOFER
PASIVO DE 10" PARA CAMIONETAS
10" ACTIVE SUBWOOFER SHALLOW
SUBWOOFER FOR PICK-UP TRUCKS
PU210A
PU210A
1
1. REMOTE CONTROLLER OUTLET:
The Remote Controller adjusts the gain. Turn
the volume knob to max before using your remote.
2. BOOST: The boost ranges from 0dB to 6dB.
3. PHASE: Phase adjusting switch, the phase
ranges fromto 180° degrees.
4. LPF: Low pass frequency adjusting knob.
The frequency ranges from 50Hz to 200Hz.
5. GAIN: Knob for volume adjustment.
6. LOW LEVEL OUTPUT / INPUTS:
LOW LEVEL OUTPUT: A daisy chain output for
connection to another amplifier with a low level
input using only a single RCA output from the
source (head unit).
LOW LEVEL INPUT: For connection to any source
(head unit) with a low level output. This is your RCA
output from the source (head unit).
7. POWER CONNECTION TERMINALS: Connect
these to vehicle's battery. Make sure these are the
correct connections as this can damage the unit.
+12V: Connect the terminal to the vehicle's +12V
source.
REM: Connect the terminal to the remote cable
originating from the source, this controls the
amplifier switching on. The applied voltage must
be between 10 and 15 VDC.
GND: Ground terminal. Connect it to the car
chassis, and ensure the ground cable length is kept
to a minimum.
8. FUSE: Standard ATC fuse. You must use a 30A
fuse if you need to change it.
9. PROTECTION / POWER INDICATOR:
When the amplifier is operating correctly, the LED
will show as green. When the amplifier is in protec-
tion mode, the LED will show as red.
1. SALIDA DE CONTROL REMOTO:
El control remoto ajusta la ganancia. Gire la perilla
del volumen al ximo antes de utilizar el control
remoto.
2. REFUERZO: El refuerzo varía de 0dB a 6dB.
3. FASE: Interruptor de ajuste de fase. La fase varía
entre 0°a 180° grados.
4. LPF: Perilla de ajuste de la frecuencia de paso
bajo. La frecuencia varía entre 50Hz y 200Hz.
5. GANANCIA: Perilla para ajustar el volumen.
6. SALIDA / ENTRADAS DE BAJO NIVEL:
SALIDA DE BAJO NIVEL: Una salida en cadena para
la conexión a otro amplificador con una entrada de
bajo nivel utilizando lo una única salida RCA de la
fuente (reproductor principal).
ENTRADA DE BAJO NIVEL: Para la conexión a
cualquier fuente (reproductor principal) con una
salida de bajo nivel. Esta es su salida RCA de la
fuente (reproductor principal).
7.TERMINALES DE CONEXIÓN DE ALIMENTACIÓN:
conéctelos a la batería del vehículo. Asegúrese de
que sean las conexiones correctas p2-ya que pueden
dañar la unidad.
+12V: Conecte el terminal a la fuente de +12V del
vehículo.
REM: Conecte el terminal al cable remoto
procedente de la fuente, esto controla el encendido
del amplificador. El voltaje aplicado debe estar entre
10 y 15 VDC.
GND: Terminal de tierra. Conéctelo al chasis del
vehículo, y asegúrese de que la longitud del cable de
tierra es mínima.
8. FUSIBLE: Fusible ATC estándar. Debe utilizar un
fusible de 30A si necesita cambiarlo.
9. INDICADOR DE PROTECCIÓN / ALIMENTACIÓN:
Cuando el amplificador está funcionando
correctamente, el LED se mostrará en verde.
Cuando el amplificador está en modo de protección,
el LED se mostrará en rojo.
INTRUCTIONS FOR FUNCTIONS
AND CONTROLS
INSTRUCCIONES PARA FUNCIONES Y
CONTROLES


Produkt Specifikationer

Mærke: DS18
Kategori: Ikke kategoriseret
Model: PU210A

Har du brug for hjælp?

Hvis du har brug for hjælp til DS18 PU210A stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret DS18 Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer