Dürkopp Adler 1280 Manual

Dürkopp Adler Symaskine 1280

Læs gratis den danske manual til Dürkopp Adler 1280 (34 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Dürkopp Adler 1280, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/34

Instructions for service

1280 - 6

Minerva Boskovice, a.s., Sokolská 60, CZ - 680 17 Boskovice

Tel.: +420-501-453434, 453433, 494111 Fax: +420-501-452165 http://www.minerva-boskovice.com

Edition: 06/2001 Printed in Czech Republic 735 342 000 477

CONTENTS:

1. General safety instructions ............................................................................................................................................... 1

2. Introduction .......................................................................................................................................................................... 1

3. Head of the sewing machine .............................................................................................................................................. 2

3. 1 Hook and hook box .................................................................................................................................................................. 2

.. 3.1.1 Description

3.1.2 Height setting of the hook

3.1.3 Setting the distance of the hook from the needle

3.1.4 Angular setting of the hook (timing)

3.1.5 Protection of the needle and of the hook point

3.1.6 Setting of the bobbin case opener

3.1.7 Setting the regulation of the hook lubrication

3.1.8 Replacement of the hook

3.1.9 Setting the gear

3.1.10 Dismantling of the hook box

3.2 Needle and thread mechanism ................................................................................................................................. 5

3.2.1 Description

3.2.2 To check the handwheel angular adjustment

3.2.3 Height setting of the needle bar

3.2.4 Angular setting of the pin of the thread mechanism

3.2.5 Side setting of the needle bar holder and setting of the needle bed shifting

3.3 Throat plate ............................................................................................................................................................................... 7

3.3.1 Description

3.3.2 Setting the needle (the needle bar holder) in the direction of sewing (fine setting)

3.4 Front and rear guides of needles ......................................................................................................................................... 7

3.4.1 Description

3.4.2 Setting the front guide

3.4.3 Setting the rear guide

3.4.4 Setting the guide of the needles (stitch widths with needles, side by side)

3.5 Thread tensioners and limiter ............................................................................................................................................... 9

3.5.1 Description

3.5.2 Setting the tension of main and auxiliary tensioners

3.5.3 Setting the tensioning mechanism of the main tensioner

3.5.4 Setting the adapting spring

3.5.5 Setting the thread limiter

3.6 Feeding mechanism of the needle feed and of the lower feed wheel .........................................................................11

3.6.1 Description

3.6.2 Stitch length mechanism

3.6.2.1 Setting the upper eccentric

3.6.2.2 Setting the prop

3.6.2.3 a Forward and rearward stitch length distribution (rough)

3.6.2.3 b Forward and rearward stitch length distribution (fine)

3.6.2.4 Setting of the control knob (including the stitch length limitation)

3.6.3 Setting the needle feed

3.6.4 Lower feed wheel

3.6.4.1 Feeding clutches

3.6.4.1.1 Description

3.6.4.1.2 Setting the lever of the second step of feeding(angle, position)

3.6.4.1.3 Setting of the lower eccentric

3.6.4.1.4 Setting the engagement and disengagement of the clutches

3.6.4.2 Wheel feeder and its post

3.6.4.2.1 Height setting of the feeder

3.6.4.2.2 Replacement of the feeder

3.6.5 Setting the top roller (pressing force, height)

3.7 Feeding mechanism of the top roller ................................................................................................................................15

3.7.1 Description

3.7.2 Side setting of the indented lower pulley

3.7.3 Side setting of the indented upper pulley