Dürkopp Adler 744 Manual

Dürkopp Adler Symaskine 744

Læs gratis den danske manual til Dürkopp Adler 744 (26 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Dürkopp Adler 744, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/26

Contents Page

Part 3: Service Instructions 744-122

1. Notes Prior to Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Transport Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Right End Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 Left End Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Marking on the Material Guide Rail and the Material Stopper . . . . . . . . . . . . . . . . . 5

2.4 Transport Carriage Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.5 Material Guide Rail Stroke Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. Material Stopper Mounting and Material Stopper . . . . . . . . . . . . . . . . . . . . . . 9

4. Distance from the Material Guide Rail to the Needle . . . . . . . . . . . . . . . . . . . . 10

5. Light Barrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6. Synchronizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7. Adjusting the Machine Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7.1 Folding Over the Machine Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7.2 Adjustment Disk to the Arm Shaft Crank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7.3 Position of the Lower Timing Belt Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7.4 Rocker Bolt for the Hook Drive and the Left Shaft Bearing . . . . . . . . . . . . . . . . . . . 15

7.5 Hook Drive Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7.6 Needle Avoidance Movement of the Hook (Ellipse Width) . . . . . . . . . . . . . . . . . . . 16

7.7 Symmetry of Looper Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7.8 Hook in Hook Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.9 Setting the Hook to the Needle Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.10 Needle Rod Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7.11 Needle Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.12 Bobbin Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.13 Needle Thread Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

8. Thread Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

9. Throw-Over Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.1 Distance to the sewing unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.2 Setting the Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.3 Setting the Height of the Counterholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.4 Setting the Position of the Placement Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.5 Setting the Speed of the Smoother Movement . . . . . . . . . . . . . . . . . . . . . . . . . 27

Home

Part 3: Service Instructions

1. Notes prior to adjustment

These servicing instructions describe the

adjustments to the sewing unit in the appropriate

order.

Here it is to be noted that the various adjustment

positions are interdependent. It is therefore

essential that the adjustments be made in the order

described.

Attention Danger of Breakage!

After disassembly and prior to restar ting the

sewing unit, the required adjustments must

be made as described in these instructions.

The sewing unit must not be started with the

wrong direction of motor rotation.

Attention Risk of Injury!

Should adjustments have to be made in the

area of the needle and the needle not be

absolutely necessary to these, it should be

removed to avoid injuries.

The main switch should always be turned off.

The only exceptions are those adjustments

which must be made with testing, setting or

sewing programs from the control unit.

Attention!

With some adjustments it is necessary to move the

transport carriage manually.

This is possible with the main switch OFF.

When the main switch is ON, e.g. when the testing

program is to be used, the step motor is under

current and its braking effect stops manual

movement. In this case the fuse 3 for the step

motor must be removed from the control panel.

For all adjustments to par ts forming stitches a

faultless needle must be used.

Upon request you will receive the following

adjustment gauges:

Order no. Application

933 80207 Dail gauge

933 80193 Angle for the looper symmetry setting

933 80194 Indicator for the looper symmetry

setting

933 80200 Feeler gauge for the thread take-up

disk

933 80203 Gauge for the hook drive housing

933 80221 Gauge for the rocker bolt in the hook

drive

An adjustment disk in the machine head has the

notches A,B,C and D. An arresting pin, order no.

211700, for locking into the various adjustment

positions can be found in the package with the unit.

In conjunction with the letters on the handwheel the

arresting pin can be pushed into one of the notches

through a hole.

Transport carriage

Caution in the area of moving machine par ts

- Risk of Injury -

The transport carriage is guided on the extension

pipes at the front by the ball sleeves 2 and at the

back by the track rollers 1.

They have been set tight at the factor y. To remove

axial play only loosen the excentrically bearinged

lower rollers 1 and set tight. Check for ease of

movement.

The transport carriage is advanced by the step

motor for the following speeds: Stitch condensing,

Normal stitch length and transport carriage return.

Through a coding on the material stopper it is

possible by primary seams to reduce return speed

for a partial or complete run according to the rail

form. See 5.1.10 of the Microcontrol summar y.

1 2

Produkt Specifikationer

Mærke:	Dürkopp Adler
Kategori:	Symaskine
Model:	744

Har du brug for hjælp?

Hvis du har brug for hjælp til Dürkopp Adler 744 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Symaskine Dürkopp Adler Manualer

Dürkopp Adler 2171-5 Manual

3 August 2025

Dürkopp Adler 1365-7 Manual

3 August 2025

Dürkopp Adler D888 e-con Manual

3 August 2025

Dürkopp Adler D887 e-con Manual

3 August 2025

Dürkopp Adler 550-869 Manual

3 August 2025

Dürkopp Adler 533 Manual

3 August 2025

Dürkopp Adler D888 Manual

3 August 2025

Dürkopp Adler 805 Manual

3 August 2025

Dürkopp Adler 550-767 Manual

13 Oktober 2024

Dürkopp Adler 204-370 Manual

11 Oktober 2024

Symaskine Manualer

Nyeste Symaskine Manualer

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Juki MS-1261A-DWS Manual

9 August 2025