Dürkopp Adler 869 Manual

Dürkopp Adler Symaskine 869

Læs gratis den danske manual til Dürkopp Adler 869 (66 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Dürkopp Adler 869, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/66

INSTRUCTIONS

SEPARATION KIT

RMK-3

Thank you for purchasing the RMK-3

SEPARATION KIT

The RMK-3 allows you to install the mobile trans-

ceiver front panel separately from the main body for

added installation convenience and operation. Use

either the optional OPC-607, OPC-608 or OPC-609

SEPARATION CABLE

with the RMK-3.

• In this instruction, the illustration is described using the IC-

F5060 series transceiver.

■ Separation

The optional OPC-607 , OPC-608 (3 m; 9.84 ft) (8 m; 26.3 ft) or

OPC-609* (1.9 m; 6.3 ft)

SEPARATION CABLE

is required for in-

stalling the transceiver front panel and main body separately.

*For Europe version, only the OPC-609 is available.

q Turn the transceiver’s power OFF, then disconnect the DC

power cable.

w Unscrew the 4 bottom screws, then remove the bottom

cover from the transceiver in the direction of the arrow.

e Remove the front panel from the main body using a stan-

dard screw driver as shown below.

r Disconnect the ﬂat cable from the front panel.

t Unscrew the 4 rear plate screws, then remove the rear

plates from both the front panel and main body attach-

ments.

☞ Continue to the back page.

Rear plate

*This illustration

shows the descrip-

tion for the front

panel attachment.

Unscrew the cir-

cuit board screw.

Front panel

Flat cable Main body

Front panel

Flat cable

Main body

Front panel

Standard

screw driver

Bottom cover

CAUTION! To avoid damage to the transceiver, turn the

power OFF before separating the front panel from the

main body.

■ Supplied accessories

Main body attachment

Front panel attachment Flat cable

Mounting bracket Flat washers

(M5)

Spring washers

(M5)

Mounting screws

(M5 12)×

Self-tapping screws

(M5 16)×

Bracket screwsNuts (M5)

Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-

porated (Japan) in the United States, the United Kingdom, Germany, France,

Spain, Russia and/or other countries.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6573H-1EX Printed in Japan

■ Mounting

2 types of mounting styles are available one is overhead—

mounting, and other one is on-board mounting.

Mount the front panel and the attachment securely with the

4 supplied screws to a thick surface which can support more

than 1.5 kg. (Overhead mounting)

On-board mounting

Overhead mounting

When using

self-tapping screws

Flat washer

Spring washer

Bracket

screw

Bracket screw

■ Attachment

For the front panel attachment:

q Connect the optional OPC-607, OPC-608 or OPC-609 to

the front panel attachment as shown below.

After the cable connection, replace the removed rear plate

and the 4 screws.

• The optional cable can be inserted into either the left or right

grooves as desired on the back of the attachment.

w Connect the ﬂat cable (q) as shown below, and then at-

tach the front panel and the attachment (w).

• ﬂ Ensure the at cable is inserted correctly, and not upside down.

For the main body attachment:

e Connect the optional OPC-607, OPC-608 or OPC-609 to

the main body attachment as shown below.

After the cable connection, replace the removed rear

plate.

• The optional cable can be inserted into either the left or right

grooves as desired on the back of the attachment.

r Connect the supplied ﬂat cable* and ground cable (coming

from the RMK-3) as shown below.

*Ensure the at cable and attachment are inserted/attached cor-ﬂ

rectly, and not upside down.

t Replace the removed bottom cover and 4 screws, then re-

connect the DC power cable.

Main body attachment

to transceiver s’

main body

Main body

Main body attachment*

Flat cable*

from the RMK-3

Use the attached screw

OPC-607/

OPC-608/

OPC-609

Rear plate

Main body attachment

Cable groove

Use the screw re-

moved from the cir-

cuit board in step t

on the front page, to

connect the cable lug.

Front panel

Front panel attachment

Flat cable

Attach the front

panel and attach-

ment securely.

OPC-607/

OPC-608/

OPC-609 Rear plate

Front panel attachment

Use the screw re-

moved from the cir-

cuit board in step t

on the front page, to

connect the cable lug.

Cable groove

Printed on recycled paper with soy ink.

Produkt Specifikationer

Mærke:	Dürkopp Adler
Kategori:	Symaskine
Model:	869

Har du brug for hjælp?

Hvis du har brug for hjælp til Dürkopp Adler 869 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Symaskine Dürkopp Adler Manualer

Dürkopp Adler 2171-5 Manual

3 August 2025

Dürkopp Adler 1365-7 Manual

3 August 2025

Dürkopp Adler D888 e-con Manual

3 August 2025

Dürkopp Adler D887 e-con Manual

3 August 2025

Dürkopp Adler 550-869 Manual

3 August 2025

Dürkopp Adler 533 Manual

3 August 2025

Dürkopp Adler D888 Manual

3 August 2025

Dürkopp Adler 805 Manual

3 August 2025

Dürkopp Adler 550-767 Manual

13 Oktober 2024

Dürkopp Adler 204-370 Manual

11 Oktober 2024

Symaskine Manualer

Nyeste Symaskine Manualer

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Juki MS-1261A-DWS Manual

9 August 2025