Dürkopp Adler 8967 Manual
Dürkopp Adler
Symaskine
8967
Læs gratis den danske manual til Dürkopp Adler 8967 (32 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Dürkopp Adler 8967, eller vil du spørge andre brugere om produktet?
Side 1/32
6SH]LDOQlKPDVFKLQH
6HUYLFHDQOHLWXQJ
,QVWUXFWLRQVIRUVHUYLFH
,QVWUXFWLRQVGHVHUYLFH
3RVWIDFK'%LHOHIHOG 3RWVGDPHU6WUDH'%LHOHIHOG
7HOHIRQ 7HOHID[ ZZZGXHUNRSSDGOHUFRP
$XVJ(GLWLRQ 3ULQWHGLQ)HGHUDO5HSXEOLFRI*HUPDQ 7HLOH3DUW1R
'
*%
)
General safety instructions
The non-observance of the following safety instructions can cause
bodily injuries or damages to the machine.
1. The machine must only be commissioned in full knowledge of the
instruction book and operated by persons with appropriate
training.
2. Before putting into service also read the safety rules and
instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of
the machine without the safety devices is not permitted. Observe
all the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, presser foot,
needle plate, feed dog and bobbin) when threading, when the
workplace is left, and during service work, the machine must be
disconnected from the mains by switching off the master switch or
disconnecting the mains plug.
5. Daily servicing work must be carried out only by appropriately
trained persons.
6. Repairs, conversion and special maintenance work must only be
carried out by technicians or persons with appropriate training.
7. For service or repair work on pneumatic systems, disconnect the
machine from the compressed air supply system (max. 7-10 bar).
Before disconnecting, reduce the pressure of the maintenance
unit.
Exceptions to this are only adjustments and functions checks
made by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by
electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted,
except as specified in regulations DIN VDE 0105.
10. Conversion or changes to the machine must be authorized by us
and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time
as the entire sewing unit is found to comply with EC directives.
Produkt Specifikationer
| Mærke: | Dürkopp Adler |
| Kategori: | Symaskine |
| Model: | 8967 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Dürkopp Adler 8967 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Symaskine Dürkopp Adler Manualer
13 Oktober 2024
11 Oktober 2024
6 Oktober 2024
13 September 2024
3 September 2024
2 September 2024
28 August 2024
23 August 2024
21 August 2024
20 August 2024
Symaskine Manualer
- Kenmore
- Hugin
- LERAN
- Mediashop
- Carina
- Husqvarna-Viking
- Medion
- Yamato
- Guzzanti
- RCE
- Veritas
- Lervia
- Huskystar
- Kayser
- Anker-Bernette
Nyeste Symaskine Manualer
11 Juli 2025
11 Juli 2025
11 Juli 2025
11 Juli 2025
11 Juli 2025
11 Juli 2025
10 Juli 2025
10 Juli 2025
10 Juli 2025
10 Juli 2025