EasyMaxx Z07787 Manual


Læs gratis den danske manual til EasyMaxx Z07787 (4 sider) i kategorien Køling frysning. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om EasyMaxx Z07787, eller vil du spørge andre brugere om produktet?

Side 1/4
DE Anleitung
Kundenservice / Importeur:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Deutschland • +49 38851 314650 *)
*) 0 – 30 Ct. / Min. in das dt. Festnetz. Kosten variieren je nach Anbieter.
Alle Rechte vorbehalten.
Artikelnummer: 07787
Sehr geehrte Kundin, sehr geehrter Kunde,
wir freuen uns, dass Sie sich für diesen Outdoor-Flaschen kühler
entschieden haben. Sollten Sie Fragen zum Artikel sowie zu Er-
satz- / Zubehörteilen haben, kontaktieren Sie den Kundenservice
über unsere Webseite: www.service-shopping.de
Erklärung der Symbole und Signalwörter
Gefahrenzeichen: Dieses Symbol zeigt Verletzungs-
gefahren an. Die dazugehörenden Sicherheitshinweise
aufmerksam durchlesen und an diese halten.
Ergänzende Informationen
WARNUNG warnt vor möglichen schweren Verletzungen und
Lebensgefahr
VORSICHT warnt vor leichten bis mittelschweren
Verletzungen
WICHTIGE HINWEISE
Der Artikel ist zum Kühlhalten von bis zu 15 Getränke aschen
bestimmt. Er dient jedoch nicht zum Herunterkühlen der Ge-
tränke.
Der Artikel eignet sich für herkömmliche 0,33 l und 0,5 l Ge-
tränke aschen aus Glas und Kunststoff.
Die maximale Traglast beträgt 10 kg.
Der Artikel ist für den Privatgebrauch, nicht für eine gewerb-
liche Nutzung konzipiert.
Den Artikel nur wie in der Anleitung beschrieben nutzen. Jede
weitere Verwendung gilt als bestimmungswidrig.
WARNUNG – Verletzungs- und Erstickungsgefahr! Kinder
und Tiere von Artikel und Verpackungsmaterial fernhalten.
Der Artikel ist kein Spielzeug!
VORSICHT – Verletzungsgefahr!
Das Gestell niemals auf dem Führungsring abstellen! Es
könnte umfallen und die Flaschen könnten zu Bruch gehen.
Das Gehäuse niemals offen lassen. Es darf keine
Stolpergefahr darstellen!
Ausreichend Freiraum um das Erdloch lassen (min. 50 cm).
Den Artikel bei Bedarf mit einem feuchten Tuch und ggf. mil-
dem Reinigungsmittel reinigen. Keine ätzenden oder scheu-
ernden Reinigungsmittel verwenden! Diese könnten die Ober-
äche beschädigen.
Lieferumfang und Artikelübersicht
1 Griff
2 Ablage für
5 Flaschen (3 x)
3 Stange (3-teilig)
4 Führungsring
5 Gehäuse (3-teilig)
6 Deckel (isoliert)
3
5
3
1
2
4
6
Vor dem ersten Gebrauch
Alle Teile auspacken und eventuelle Schutzfolien bzw. Aufkle-
ber entfernen. Den Lieferumfang auf mögliche Transportschä-
den prüfen. Sollte ein Transportschaden festgestellt werden,
den Artikel nicht (!) verwenden, sondern umgehend den Kun-
denservice kontaktieren.
Artikel zusammenbauen (siehe „Zusammenbau“).
Erdloch ausheben (siehe „Erdloch ausheben“).
Inbetriebnahme
Zusammenbau
1. Die drei Gehäuseteile (5) miteinander verschrauben.
2. Eine Ablage (2) an das untere Ende eines Stangenteils (3)
schrauben. Die Aussparungen der Ablage müssen nach oben
zeigen. Diesen Schritt für die beiden übrigen Ablagen wieder-
holen.
3. Die drei entstandenen Einheiten miteinander verschrauben,
sodass ein Gestell entsteht.
4. Den Griff (1) an das obere Ende des Gestells schrauben.
5. Den Führungsring (4) in die unterste Ablagenöffnung stecken.
Erdloch ausheben
BEACHTEN
Sicherstellen, dass keine Leitungen angebohrt bzw. zerstört
werden. In Erfahrung bringen, wo evtl. Leitungen verlaufen,
und diese umgehen.
Zum Ausheben des Erdlochs eignet sich am besten ein
Erdlochbohrer. Dabei unbedingt die Anweisungen in
der Anleitung des Erdlochbohrers beachten! Dieser ist
nicht im Lieferumfang enthalten. Tipp: Ein Erdlochbohrer
kann in den meisten Baumärkten ausgeliehen werden.
1. Ein Erdloch ausheben (Durchmesser ca. 25 cm). Dieses muss
ca. 90 cm tief sein, dass die Erde mit der Kante des Gehäu-
ses (5) abschließt.
2. Das zusammengeschraubte Gehäuse im Erdloch platzieren.
3. Das Erdloch um das Gehäuse herum mit Erde auffüllen. Diese
dabei vorsichtig verdichten.
4. Zum Entfernen des Gehäuses aus der Erde das Erdloch um
das Gehäuse großzügig erweitern. Das Gehäuse sollte leicht
in einem Stück aus der Erde herausgezogen werden können.
Benutzung
BEACHTEN
Die maximale Traglast des Artikels darf nicht überschritten
werden.
1. Kalte (!) Flaschen in die Aussparungen der Ablagen (2) ein-
setzen.
2. Das mit Flaschen bestückte Gestell in das Gehäuse (5) in der
Erde einsetzen.
3. Den Deckel (6) auf das Gehäuse aufsetzen.
4. Um den Artikel bzw. dessen Inhalt vor direkter Sonnenein-
strahlung zu schützen, den Deckel zusätzlich abdecken, z. B.
durch Abstellen eines Blumentopfes auf dem Deckel.
Artikeldaten
Artikelnummer: 07787
Maße:
Höhe: ca. 90 cm
Breite: ca. 22 cm
Gewicht: 2,3 kg
Traglast: max. 10 kg
Entsorgung
Das Verpackungsmaterial und den Artikel umweltgerecht ent-
sorgen und der Wertstoffsammlung zuführen.
Z 07787 M DS V3 0118
EN Instructions
Customer Service / Importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany • +49 38851 314650 *)
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
All rights reserved.
Article number: 07787
Dear Customer,
We are delighted that you have chosen this outdoor bottle cooler.
If you have any questions about the article and about spare parts /
accessories, contact the customer service department via our
website: www.service-shopping.de
Explanation of Symbols and Signal Words
Danger symbol: This symbol indicates dangers of injury.
Read through the associated safety instructions carefully
and follow them.
Supplementary information
WARNING warns of possible serious injuries and danger to
life
CAUTION warns of slight to moderate injuries
IMPORTANT INSTRUCTIONS
The article is intended to be used for keeping up to 15 drink
bottles cool. However, it is not intended to be used to chill the
drinks.
The article is suitable for conventional 0.33 l and 0.5 l drink
bottles made of glass and plastic.
The maximum load it can carry is 10 kg.
The article is designed for personal use only and is not
intended for commercial applications.
The article should only be used as described in these instruc-
tions. Any other use is deemed to be improper.
WARNING – Risk of injury and suffocation! Keep children
and animals away from the article and packaging material.
The article is not a toy!
CAUTION – Danger of injury!
Never place the frame down on the guide ring! It could topple
over and the bottles could be broken.
Never leave the housing open. It must not present a trip
hazard!
Leave a suf cient amount of clear space around the hole in the
ground (min. 50 cm).
Clean the article with a damp cloth and mild cleaning agent
if necessary. Do not use any corrosive or abrasive cleaning
agents! These could damage the surface.
Items Supplied and Article Overview
1 Handle
2 Tray for 5 bottles
(3 x)
3 Rod (3-piece)
4 Guide ring
5 Housing (3-piece)
6 Lid (insulated)
3
5
3
1
2
4
6
Before Initial Use
Unpack all parts and remove any protective lms or stickers.
Check the items supplied for possible transport damage. If you
should nd any transport damage, do not (!) use the article, but
contact the customer service department immediately.
Assemble the article (see the “Assembly” section).
Dig a hole in the ground (see the “Digging a Hole in the
Ground” section).
Putting Into Operation
Assembly
1. Screw the three housing parts (5) to one another.
2. Screw one tray (2) onto the bottom end of one rod part (3). The
recesses of the tray must be facing upwards. Repeat this step
for the other two trays.
3. Screw together the three resulting units to create a frame.
4. Screw the handle (1) onto the top end of the frame.
5. Plug the guide ring (4) into the lowest tray opening.
Digging a Hole in the Ground
PLEASE NOTE
Make sure that no cables are bored into or destroyed. Find out
where cables may possibly run and avoid them.
A earth auger is best suited for digging the hole in the
ground. Make sure you follow the instructions in the
guide for the earth auger! This is not supplied with the
article. Tip: A earth auger can be borrowed from most DIY
stores.
1. Dig a hole in the ground (diameter of approx. 25 cm). It must be
around 90 cm deep so that the ground is ush with the edge
of the housing (5).
2. Place the screwed-together housing in the hole in the ground.
3. Fill the hole in the ground around the housing with earth. Care-
fully compact it as you do so.
4. To remove the housing from the ground, spread out the hole in
the ground around the housing. It should be possible to pull the
housing out of the ground easily in one go.
Use
PLEASE NOTE
The maximum load capacity for the article must not be
exceeded.
1. Insert cool (!) bottles into the recesses of the trays (2).
2. Insert the frame containing the bottles into the housing (5) in
the ground.
3. Place the lid (6) on the housing.
4. To protect the article and its contents from direct sunlight, also
cover the lid, e. g. by placing a ower pot on top of the lid.
Article Data
Article number: 07787
Dimensions:
Height: approx. 90 cm
Width: approx. 22 cm
Weight: 2.3 kg
Load capacity: max. 10 kg
Disposal
Dispose of the packaging material and the article in an en-
vironmentally friendly manner and take them to a recycling
centre.
Z 07787 M DS V3 0118


Produkt Specifikationer

Mærke: EasyMaxx
Kategori: Køling frysning
Model: Z07787

Har du brug for hjælp?

Hvis du har brug for hjælp til EasyMaxx Z07787 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Køling frysning EasyMaxx Manualer

EasyMaxx

EasyMaxx Z07787 Manual

24 August 2024

Køling frysning Manualer

Nyeste Køling frysning Manualer