Edimax DP-240W52V Manual

Edimax Ikke kategoriseret DP-240W52V

Læs gratis den danske manual til Edimax DP-240W52V (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Edimax DP-240W52V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

-DIN Rail Power Supply Quick Installation Guide

- 1 -

I. INTRODUCTION:

DP- -240W Series DIN Rail Power Supply can be mounted on TS35/7.5 or

TS35/15 standard DIN Rail.

II. INSTALLATION

II-1. DIN-Rail Mounting

Please follow below Rail Power Supply on the instruction to mount the DIN-

DIN- Rail track.

1. Insert the unit upper end of the DIN-Rail

mounting bracket into the DIN-Rail track from

its upper side.

2. Slide it downward until it hits the stop.

3. Lightly push the bottom of the DIN-Rail

mounting bracket into the track.

4. Check if the DIN-Rail mounting bracket is

tightly attached to the track.

NOTE:

 Mount the unit on DIN-Rail rack in vertical

position to keep the input terminals at the

bottom and output on the top. Other

positions are not allowed such as desktop,

upside down or horizontal mounting.

 Disconnect AC power before installing wiring.

-DIN Rail Power Supply Quick Installation Guide

- 2 -

II-2. W iring AC Power Inputs and DC Output

1. Maintaining good ventilation clearances for DIN Rail power supply,

10mm left and right, 40mm above and 20mm below, in order to

prevent it from overheating.

2. To dissipate heat, please keep 15 cm away from the adjacent heat

source.

3. (100 The AC input - (240V) and DC output 24V/52V) wire recommended

at least 0.8mm² (AWG18) and UL1007 (withstand temperature > 80°C).

AWG

Rated Current of Equipment(Amp)

Cross- ( ) section of Lead mm²

0.8mm²

4. Recommended wire strapping length: 6.5mm(0.255”)

5. AC Power Input Wiring: For AC (100—240V) power input wiring, please

connect to L (Live line), N (Null Line) and GND (Ground) terminals.

Tighten the screws to prevent the wires from

loosening.

6. DC Power Output Wiring: Insert the

Negative / Positive DC wires into the PWR

terminals (V5 V52-, 2+) respectively. Tighten

the screws to prevent the wires from

loosening.

7. “+ V Ad j “ DC Output Voltage Regulator can

adjust the DC voltage from 48V to 56V

8. Insert the wires (no electrical polarity) into

the “DC OK” terminal block (Fault Alarm

Relay). Tighten the screws to prevent the

wires from loosening.

DC Power Output

AC Power Input

DC Output

Voltage

Regulator

Power OK

LED

Produkt Specifikationer

Mærke:	Edimax
Kategori:	Ikke kategoriseret
Model:	DP-240W52V
Vekselstrømsindgangsspænding:	90 - 264 V
Vekselstrømsindgangsfrekvens:	47 - 63 Hz
Bredde:	114 mm
Dybde:	122 mm
Højde:	63 mm
Vægt:	818 g
Produktfarve:	Black, Grey
Produkttype:	Strømforsyning
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	20 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	10 - 85 %
Driftstemperatur (T-T):	-25 - 70 °C
Certificering:	FCC, CE LVD EN62368, UL UL62368, UL CB IEC62368
Bæredygtighedscertifikater:	CE, RoHS
Overholdelse af bæredygtighed:	Ja
DC udgangsspænding:	52 V
Total effekt:	240 W
Strømbeskyttelsesfunktioner:	Over current, Over voltage, Short circuit
DIN-skinne montering:	Ja
DC spændingsområde:	48 -56 V