Electro-Voice EBK-1 Manual

Electro-Voice Ikke kategoriseret EBK-1

Læs gratis den danske manual til Electro-Voice EBK-1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Electro-Voice EBK-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

100

150

200

250

300

350

400

450

500

550

600

650

700

0 10 20 30 40 50 60 70 80 90

Angle (Degrees)

Working Load Limit (lbs)

113

136

159

181

204

227

249

272

295

318

Working Load Limit (kg)

625 lbs (283 kg) @ 0°

250 lbs (113 kg) @ 30°

138 lbs (62 kg) @ 60°

113 lbs (51 kg) @ 90°

EBK-1

3/8” Eyebolt

Attachment Kit

User Instructions

EBK-1 3/8” Eyebolt Attachment Kit

The Electro-Voice® EBK-1 Eyebolt Attachment Kit contains three shoulder eyebolts, along with three fender wash-

ers for load distribution, which attach to Electro-Voice® speakers that have integrated 3/8” suspension points.

The eyebolt attachment points can be used to suspend the Electro-Voice® speakers using hardware rated for

overhead lifting. The loudspeaker is suspended using two main suspension points with a pull-up point in the back

for aiming. Two suspension points can be used to prevent the speaker from swaying, but the rigging hardware

(shackles, etc.) attaching to the eyebolt must fit through the 25-mm (1-in.) opening.

Figure 1: Suspension Point and Load Angles

3/8”

Eyebolt

Figure 2: Removing the 3/8” Bolts from the Loudspeaker

Table 2: Working-Load vs. Angle (8:1 Safety Factor)

Figure 3: Installing Fender Washers and

Eyebolts to the Loudspeaker

Installation Instructions:

1. Remove the 3/8-16 shoulder bolts from the speaker (See Figure 2).

2. Screw the lifting eyebolt and fender washer into the insert until the fender washer has contacted the wood (See

Figure 3).

3. Finger tighten eyebolt until correct alignment position is obtained, a maximum of one complete turn.

4. Use certified hardware rated for overhead lifting to suspend the speaker (See Figure 6).

WARNING: Eyebolts must be fully seated and oriented in the plane of pull (Figure 4). Always use the fender washers to distribute

the load on the enclosure (Figure 5). Overtightening the eyebolt with a wrench, screwdriver, etc. can result in system failure and

injury. Consult the loudspeaker user manual for the loudspeaker load ratings and specific requirements.

Part No. Quantity Description Material

5542930 3 3/8”-16 x 32mm (1.25 in.) Shoulder Eyebolts Drop Forged Steel

HDW000006-000 3 3/8” ID x 1-1/2” OD Fender Washers Stainless Steel, Black

Table 1: EBK-1 Contents

Fender

Washer

3/8”

Bolt

Load

Correct Incorrect

Load

90°

0°

30°

60°

12000 Portland Avenue South, Burnsville, MN 55337

Phone: 952/884-4051, Fax: 952/884-0043

www.electrovoice.com

Part Number 534260 Rev C

U.S.A. and Canada only. For customer orders, contact Customer Service at:

800/392-3497 Fax: 800/955-6831

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

+ 49 9421-706 0 Fax: + 49 9421-706 265

Other Internatonal locations. For customer orders, Contact Customer Service at:

+ 1 952 884-4051 Fax: + 1 952 887-9212

For warranty repair or service information, contact the Service Repair department at:

800/685-2606

For technical assistance, contact Technical Support at: 866/78AUDIO

Specifications subject to change without notice.

Electro-Voice®

Figure 6: Examples of Useful Suspension Hardware

Figure 4a: Eyebolts shown oriented in the

plane of pull (CORRECT)

Figure 4b: Eyebolts NOT oriented in the

plane of pull (INCORRECT)

Figure 5b: Eyebolt shown without Washer (INCORRECT)

WARNING: Suspending any object is potentially

dangerous and should only be attempted by

individuals who have a thorough knowledge of the

techniques and regulations of suspending objects

overhead. Electro-Voice® strongly recommends

that loudspeakers be suspended taking into ac-

count all current national, federal, state and local regulations. It

is the responsibility of the installer to ensure that all loudspeak-

ers are safely installed in accordance with all such regulations.

When loudspeakers are suspended, Electro-Voice® strongly

recommends that the system be inspected at least once a year.

If any sign of weakness or damage is detected, remedial action

should be taken immediately. Any hardware used to suspend a

loudspeaker that is not associated with Electro-Voice® is the

responsibility of others.

Anchor

Shackle

Threaded

Chain

Connector

Carabiner-

Type

Snap Hook

No Washer

Used

Washer

Used

Figure 5a: Eyebolt shown with Washer (CORRECT)

Produkt Specifikationer

Mærke:	Electro-Voice
Kategori:	Ikke kategoriseret
Model:	EBK-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice EBK-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro-Voice Manualer

Electro-Voice MFX-12MC Manual

13 Januar 2025

Electro-Voice TCB-1 Manual

12 Januar 2025

Electro-Voice VRK-3W Manual

12 Januar 2025

Electro-Voice TCA-ZX1 Manual

8 Januar 2025

Electro-Voice TK-150 Manual

8 Januar 2025

Electro-Voice N/D767a Manual

8 Januar 2025

Electro-Voice N/D478 Manual

8 Januar 2025

Electro-Voice AGCD Manual

8 Januar 2025

Electro-Voice EVC-WB Manual

8 Januar 2025

Electro-Voice XGS-3 Manual

8 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg CVI120GE Manual

17 Juni 2025

Panduit VS-CKP4-000 Manual

17 Juni 2025

Yamazen LTH-2BH Manual

17 Juni 2025

Philips ASH4511CH Manual

17 Juni 2025

Yamazen MNW-1890CJ Manual

17 Juni 2025

D-Link DMC-700SC Manual

17 Juni 2025

Makita DHP490 Manual

17 Juni 2025

Royal Catering RC-BFWH12030 Manual

17 Juni 2025

Makita TW011G Manual

17 Juni 2025

Philips 50BDL2050Q Manual

17 Juni 2025