Electro-Voice MB200 Manual

Electro-Voice Ikke kategoriseret MB200

Læs gratis den danske manual til Electro-Voice MB200 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Electro-Voice MB200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

# of Enclosures # of Kits Req’d

in Array: Mb 200 Mb300

2 2 1

3 3 2

4 4 3

5 5 4

6 (complete circle) 6 6

Description

The Mb200 installation kit consists of a

U-bracket, two M8 x 1.25 hex-head bolts,

four lock washers, two friction pads, and two

3/8-24 hex-head bolts (see Chart 1). The kit

is designed to accommodate the System

200TM installation in a variety of ways.

Wall or Ceiling Mounting:

The robust design of the Mb200 installation

bracket allows the System 200TM speakers

to be mounted in almost any position to ob-

tain the desired sound coverage (see Figure

3).

Flying Installations

The Mb200 bracket “captures” the speaker

in a rigid frame which has structurally sound

locations for attaching rigging hardware.

These attachment points are four 12.7-mm

(1/2-in.) diameter holes located on the ends

of the bracket. A 3/8-in. “quick link” (or simi-

lar hardware) can be readily connected to

each attachment point.

System 200TM speakers can be flown indi-

vidually in either a horizontal or vertical po-

sition, or two speakers can be flown together

in a vertical position (see Figures 4 and 5).

System 200TM Horizontal Arrays

Arrays of two to six speakers are securely

supported in a frame comprised of Mb200

and Mb300 brackets. To create a horizontal

array, two Mb200 brackets are simply locked

into the correct alignment position using the

brackets from the Mb300 Horizontal Array

Mb200

And Mb200W

Installation Kit

• Mounting kit for SystemTM 200

speakers

• May be used in conjuction with

OmniMount® Series 100 support

system1

• Versatile design allows the

speaker to be aimed at any angle

from wall or ceiling

• Provides a rigid frame for flying

one or two speakers

• Creates arrays of two to six speak-

ers when used with the Mb300

Horizontal Array Kit

Kit (see Figure 6). The array is extended by

using one additional Mb200 bracket and one

300 kit for each additional speaker. To

complete the circle for a six speaker array,

one additional Mb300 kit is required. Please

refer to Chart 2 to select the exact number of

each kit needed, based on desired array size.

(Note: refer to Mb300 Horizontal Array Kit

engineering data sheet for detailed instruc-

tions on System 200TM horizontal array con-

struction using Mb200 Installation and

300 Horizontal Array Kits.)

Item Description Quanity Part Number

A Bracket 1 71914

B M8 x 1.25 hex head bolt 2 63310

C 5/16 split ring lock washer 2 38144

D 3/8-24 hex head bolt 2 63311

E 3/8 split ring lock washer 2 38834

F Friction washer 2 38829

CHART 2: Kit Requirements for

System 200TM Horizontal

Array Construction

CHART 1: Mb200 Installation Kit Parts List

Mb200/Mb200W Installation Kit

Mb200 SPECIFICATION GRAPHICS

FIGURE 1 —Attaching Mb200 Bracket

to System 200TM Speaker (exploded view)

22.90 in. (582 mm) 0.33 in. (8 mm)

3.69 in. (94 mm)

2.75 in. (70 mm)

8.0 in.

(203 mm)

8.0 in.

(203 mm)

5.0 in. (127 mm)

HOLE PATTERN FOR OmniMount

LOCATED ON BOTH SIDES AND BACK

0.33 in. (8 mm)

0.5 in. (13 mm)

3/8–24

10.87 in. (276 mm)

24.90 in. (632 mm)

Wall Mounting Instructions

CAUTION: Due to the weight of System

200TM speakers, it is imperative that the

Mb200 bracket be properly secured to the

wall or ceiling. The choice of fastener (not

provided with this kit) will be determined

by the material and construction of the

mounting surface.

1. Refer to Figure 1 for the following steps.

2. Remove the paper backing from one of

the friction pads (F) and, making sure the

holes are aligned, attach to the U-bracket (A)

as shown. Attach the second friction pad in

a similar manner.

3. Attach the U-bracket to the wall or ceil-

ing using fasteners (not supplied) that are

suitable for the construction material.

4. Remove the hole plugs from the ends of

the System 200TM

speaker by gently prying

with a small screwdriver.

5. Place one of the smaller lock washers

6. Place the speaker into the U-bracket and

finger tighten the M8 bolts.

7. Rotate the speaker so that the input

panel is accessible and attach the wires to

the input panel.

8. Position the speaker for the desired cov-

erage and gently tighten the M8 bolts until

the speaker will no longer rotate. DO NOT

OVERTIGHTEN.

Note: The 3/8

-24 bolts (D) are used to

lock the speaker parallel to the bracket and

prevent it from being rotated. This is needed

when arraying the speaker for proper align-

ment and when flying in the vertical posi-

tion.

Flying Instructions

NOTE: A maximum of two speakers can

be suspended together vertically using the

Mb200 installation bracket.

1. Refer to Figure 1 for the following steps.

2. Remove the paper backing from one of

the friction pads (F) and, making sure the

holes are aligned, attach to the U-bracket (A)

as shown. Attach the second friction pad in

a similar manner.

3. Remove the hole plugs from the ends of

FIGURE 2 — Mb200 Installation Kit Dimensions

FIGURE 3 — Wall-Mounting a System 200TM

Speaker

Using the Mb200 Installation Kit

1. OmniMount is a registered trademark of OmniMount

Systems, Inc.

Produkt Specifikationer

Mærke:	Electro-Voice
Kategori:	Ikke kategoriseret
Model:	MB200

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice MB200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro-Voice Manualer

Electro-Voice Evolve 90 Manual

2 September 2025

Electro-Voice EVOLVE-WMK-PW Manual

18 Juli 2025

Electro-Voice EVOLVE-WMK-NW Manual

17 Juli 2025

Electro-Voice EVOLVE-WMK-NB Manual

17 Juli 2025

Electro-Voice EVOLVE-WMK-PB Manual

17 Juli 2025

Electro-Voice EVOLVE-TM-B Manual

17 Juli 2025

Electro-Voice EVU-CDNL4 Manual

30 Juni 2025

Electro-Voice ZLX-8-G2 Manual

26 Februar 2025

Electro-Voice MFX-12MC Manual

13 Januar 2025

Electro-Voice TCB-1 Manual

12 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025