Epson emp 8300 lcd projector Manual

Epson Beamer projektor emp 8300 lcd projector

Læs gratis den danske manual til Epson emp 8300 lcd projector (16 sider) i kategorien Beamer projektor. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Epson emp 8300 lcd projector, eller vil du spørge andre brugere om produktet?

Side 1/16
Signal Refresh rate (Hz) Resolution (dots) Resolutions for resized display (dots)
EMP-9300 EMP-8300
SVGA
XGA
SXGA
SXGA
SXGA+
UXGA
MAC13"
MAC16"
MAC19"
MAC21"
SDTV
(525i,525p,625i,625p)
HDTV(750p)
HDTV(1125i,1125p)
VGA
EGA
56/60/72/75/85/100/120, iMac*1
60/72/75/85/100/120, iMac*1
60/70/75/85/100, iMac*1
60/70/75/85
60/75/85
60
60/65/70/75/80/85
640 × 480
800 × 600
1024 × 768
1152 × 864*2
1280 × 960*2
1280 × 1024*2
1400 × 1050*2
1600 × 1200*2
640 × 480
832 × 624
1024 × 768
1152 × 870*2
640 × 350
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
960 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1016 × 768
1024 × 768
(4:3 aspect ratio)
1024 × 576
(16:9 aspect ratio)
1024 × 576
1024 × 576
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1312 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
1400 × 1050
(4:3 aspect ratio)
1400 × 788
(16:9 aspect ratio)
1400 × 788
1400 × 788
1024 × 560
VGACGA 640 × 400 1024 × 640
VGAEGA 640 × 350 1024 × 560
VGA text 720 × 350 1024 × 498
720 × 400
1400 × 766
1400 × 875
1400 × 766
1400 × 680
1400 × 778 1024 × 569
Printed on 100% recycled paper.
*1 Connection is not possible if the equipment does not have a VGA output port.
*2 The resolution for real display is the virtual (window) display resolution.
It may be possible to project signals which are not listed in the above table.
However, not all functions may be supportable with such signals.
User's Guide
"List of Supported Monitor Displays"
404696900E
03.09-.6A(C05)
Printed in Japan
List of Supported Monitor Displays
Before setting up and using this
projector, be sure to read the
User's Guide.
Do not look directly into the
projector's lens.
WARNING
Connections .................................1
Projection Preparation and
Adjustments ..................................3
Turning the Projector off ................5
Functions for Enhancing
Projection ..................................... 6
List of Configuration Setting
Menus .........................................10
Troubleshooting ...........................11
List of Supported Monitor
Displays ...........................Last page
Quick Reference Guide
9300E_cover1-4
The lamp is near the end of its operating life. Replace the lamp with a new one as soon as possible.
If you continue to use the old lamp, the possibility that the lamp may break will increase.
The lamp will switch off automatically
and projection will stop.
Wait for approximately 5 minutes.
After this, check the points to the
right. (With the EMP-8300, disconnect
the power plug first.)
User's Guide "Replacing the Lamp"
If you continue using the projector and
the temperature rises again, the lamp
will switch off automatically.
Check the points to the right.
If the indicator is flashing orange Warning
Indicator is lit or flashing green or orange Normal
If you press the button, projection will start after warm-up is complete.
Warm-up time is approximately 40 seconds.
After warm-up is complete, the indicator will change to steady green and projection will start.
Normal operation is in progress.
Cool-down time is approximately 30 seconds.
After cool-down is complete, the projector goes into standby mode.
You cannot use the remote control or the projector's control panel during cool-down.
If the problem is not fixed, stop
using the projector and
disconnect the power plug from
the electrical outlet.
Then contact your dealer or the
nearest address provided in the
"International Warranty
Conditions" section of the
Safety Instructions/World Wide
Warranty Terms
booklet.
If the projector
is close to a
wall, move it
away from the
wall.
Clean the air
filters if they are
blocked.
lit flashing off
lit flashing off
Standby
condition
Orange
Cool-down in
progress
Orange
Warm-up in
progress
Green
Projection in
progress
Green
Internal
temperature
error
(overheating)
Red
Red
High-speed
cooling in
progress
Orange
Red
Lamp
replacement
notification
Orange
DVI-D/DVI-D
digital video cable
or DVI-D/DFP
digital video cable
(optional)
VGA-HD15/
BNC PC cable
(optional)
Computer
cable or
VGA-HD15
PC cable
(accessory or optional)
Connecting to a
computer
The [Audio] port to use is
the port that is in the same
box as the port being used
to input the video signals.
* An accessory audio cable
is not supplied with the
EMP-9300. Use a
commercially-available
audio cable instead.
RCA audio cable
(commercially-
available)
To computer's
audio output port
To computer's
audio output port
Audio cable
(accessory)
To computer's monitor
output port
(Mini D-Sub 15-pin)
To computer's monitor
output port
(DVI-D or DFP)
Connections Be sure to turn the power for all components off before making any
of the following connections.
User's Guide
"Connecting to a Computer"
"Connecting to a Video Source"
9300E-QRG_01-14


Produkt Specifikationer

Mærke: Epson
Kategori: Beamer projektor
Model: emp 8300 lcd projector

Har du brug for hjælp?

Hvis du har brug for hjælp til Epson emp 8300 lcd projector stil et spørgsmål nedenfor, og andre brugere vil svare dig




Beamer projektor Epson Manualer

Beamer projektor Manualer

Nyeste Beamer projektor Manualer

Toshiba

Toshiba TLP-T60 Manual

15 Januar 2025
Bauer

Bauer Pantason M Manual

13 Januar 2025
Bauer

Bauer T17 Manual

13 Januar 2025
Bauer

Bauer Pantason S Manual

13 Januar 2025
Sanyo

Sanyo PLC EF10E Manual

17 December 2024
Viewsonic

Viewsonic PJ557DC Manual

4 Oktober 2024
XGIMI

XGIMI MoGo 2 Pro Manual

29 August 2024