Evga XC3 Manual

Evga Ikke kategoriseret XC3

Læs gratis den danske manual til Evga XC3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Evga XC3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation Guide
All steps include removing the original shroud, heatsink, and screws, and then replacing those with the included new shroud, heatsink, waterblock, and provided
screws, with a few exceptions. The number of provided screws used will vary depending on whether the card uses a backplate. Several included accessories may
include extras. EVGA recommends a Phillips #1 screwdriver for all screws.
All suitable P/N for HYBRID installation are listed below. Please refer to the following table.
The following instructions and pictures are provided to assist your installation of the EVGA XC3 Hybrid Cooling Kit to the EVGA GeForce RTX™ 3090 and 3080
graphics cards. Please be careful installing the Kit; there are several very small fasteners used that can be stripped if you are not careful.
Please be sure to keep your original shroud, heatsink, and screws so your card can be returned to its original condition in
case you ever need to submit for warranty.
Included Accessories:
3. Remove the 3 screws on the I/O bracket and set them aside. You will reuse
them later.
Instructions:
1. Remove the 8 BP screws circled in red and carefully remove the backplate (if
present). Next, remove the 4 GPU screws circled in blue and remove the GPU
bracket.
For RTX 3090 XC3 ULTRA and XC3 cards: Removing the backplate may require
some force to loosen up the thermal pads. Make sure to place the thermal pads
on the backplate as shown in the image below, as you will reuse the backplate
and thermal pads.
2. Turn the card over and remove the heatsink from the card. Remove the fan
connectors (blue, beige, and black) first, and then the LED connector (black) as
you lift the heatsink o the card.
RTX™ 3090 XC3 ULTRA
RTX™ 3090 XC3
RTX™ 3090 XC3 BLACK
RTX™ 3080 XC3 ULTRA
RTX™ 3080 XC3
RTX™ 3090 XC3 BLACK
24G-P5-3975-KR
24G-P5-3973-KR
24G-P5-3971-KR
10G-P5-3885-KR
10G-P5-3883-KR
10G-P5-3881-KR
11 12
910
8
71 32 5
4 6
13
EVGA HYBRID Shroud with VRM Heatsinks/Fan Bracket
GPU & Memory Baseplate
EVGA HYBRID Pump and Radiator
M2.5 x 6.9mm spring screws (GPU). 7 pcs. PN: BAA125069001
M2 x 8.5mm Backplate screws (BP). 10 pcs. PN: BAA120085039
Mylar washers for spring screws. 5 pcs. PN: BGD100000003
1
2
3
4
5
6
Rubber plugs. 3 pcs. PN: BGB030007002
Tube Bracket. 1 pc. PN: BJD243038000
M2 x 7mm tube bracket screws. 2 pcs. PN: BAA120070024
Zip ties 4pcs and EVGA Cable ties 2pcs
8pcs screws and 8pcs washers to mount radiator
8
9
10
11
12
Thermal Grease 1 pack
13
M2 x 5mm screws (PCB). 15pcs. PN: BAA120050054
7
4. Using a lint-free cloth and high-percentage isopropyl alcohol, carefully clean
the GPU and remove any leftover thermal putty on the graphics card in the
regions marked below. Try to replace any loose thermal pads back onto the
original heatsink/cooler in case you need to restore the card to its original
condition.

Produkt Specifikationer

Mærke: Evga
Kategori: Ikke kategoriseret
Model: XC3

Har du brug for hjælp?

Hvis du har brug for hjælp til Evga XC3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Evga Manualer

Evga

Evga XC3 Manual

29 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM LMC840 Manual

20 December 2025
IFM

IFM SMF150 Manual

20 December 2025
Ecler

Ecler VEO-XCTRL4D Manual

20 December 2025
Brondell

Brondell SMB-25 Manual

20 December 2025
Delta

Delta H71PB Manual

20 December 2025
Kichler

Kichler 4D12V27 Manual

20 December 2025
JILONG

JILONG KL-33F Manual

20 December 2025
Govee

Govee H7075 Manual

20 December 2025
Signature Hardware

Signature Hardware Greyfield 481138 Manual

20 December 2025
Aqprox

Aqprox appTPV00 Manual

20 December 2025