Extech 38070 Manual

Extech Multimeter 38070

Læs gratis den danske manual til Extech 38070 (2 sider) i kategorien Multimeter. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Extech 38070, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User’s Guide

Analog Multimeter

Model 38070

Introduction

Congratulations on your purchase of the Extech model 38070 Analog

Multimeter. This device measures AC/DC Voltage, DC Current, Resistance,

and dB, displaying measurements in analog format. Properly used, this meter

will provide many years of reliable service.

WARNING: USE EXTREME CAUTION IN THE USE OF THIS DEVICE.

Improper use of this device can result in injury or death. Follow all safeguards

suggested in this manual in addition to the normal safety precautions used in

working with electrical circuits. DO NOT service this device if you are not

qualified to do so.

Safety Instructions

This meter has been designed for safe use, but must be operated with caution.

The rules listed below must be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified

maximum:

Input Protection Limits

Function Maximum Input

V DC or V AC 500V AC and DC

mA DC 500mA DC

Resistance 50V DC/AC

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds

500V above earth ground.

4. NEVER connect the meter leads across a voltage source while the

function switch is in the current or resistance mode. Doing so can

damage the meter.

5. ALWAYS discharge filter capacitors in power supplies and disconnect the

power when making resistance tests.

6. ALWAYS turn off power and disconnect test leads before opening the

covers to replace the fuse or battery.

7. NEVER operate the meter unless the back cover and the battery and fuse

covers are in place and fastened securely.

8. If the equipment is used in a manner not specified by the manufacturer,

the protection provided by the equipment may be impaired.

Safety Symbols

This symbol adjacent to another symbol, terminal or operating

device indicates that the operator must refer to an explanation

in the Operating Instructions to avoid personal injury or damage

to the meter.

This WARNING symbol indicates a potentially hazardous

situation, which if not avoided, could result in death or serious

injury.

This CAUTION symbol indicates a potentially hazardous

situation, which if not avoided, may result damage to the

product.

This symbol advises the user that the terminal(s) so marked

must not be connected to a circuit point at which the voltage

with respect to earth ground exceeds 500V.

This symbol adjacent to one or more terminals identifies them

as being associated with ranges that may, in normal use, be

subjected to particularly hazardous voltages. For maximum

safety, the meter and its test leads should not be handled when

these terminals are energized.

This symbol indicates that a device is protected throughout by

double insulation or reinforced insulation.

Controls and Jacks

1. Scale

2. Pointer

3. Scale zero adjust

4. Ohms zero adjust

5. Rotary function switch

6. Positive V, mA and  input jack

7. COM input jack

Specifications

Function Range Accuracy

DC Voltage 500V

± 4% of full scale

250V

50V

10V

AC Voltage

(50/60Hz)

500V

± 5% of full scale

250V

50V

10V

DC Current

250mA

± 4% of full scale 50Ma

0.5mA

Resistance Rx10 (10,000 ± 5% of full scale

Rx1k (1,000,000

Decibels -10 to +56 dB (4 ranges) 0dB=1mW in 600

Max input voltage 500V AC/DC

Input Sensitivity, 2kV

Frequency Range 50/60Hz

Battery 0ne (1) 1.5V AA battery

Fuse 500mA/250 fast blow (5mmx20mm)

Operating Temperature 41 oF to 104oF (5oC to 40oC)

Storage Temperature 14 oF to 122oF (-10oC to 50oC)

Operating Humidity Max 80% up to 87ºF (31ºC) decreasing linearly to

50% at 104ºF (40ºC)

Storage Humidity <80%

Operating Altitude 7000ft. (2000meters) maximum.

Weight 3.88oz (110g)

Size 3.82x3.34x1.3” (97x65x33mm)

Safety For indoor use and in accordance with the

requirements for double insulation to IEC1010-1

(1995): EN61010-1 (1995) Overvoltage Category II

500V, Pollution Degree 2. UL, CE Approved

WARNING

CAUTION

MAX

500V

SupportLines:U.S.(877)439 (603) 324‐8324;International:+1  ‐7800

Technical    ‐Support: Option 3; E mail: support@extech.com

Repair & Returns:Option4; ‐E mail: repair@extech.com

Productspecificationsare subject tochangewithoutnotice

Please       ‐ ‐visit our website for the most up to date information

www.extech.com

FLIRCommercialSystems,Inc.,9     Townsend West, Nashua, NH 03063

USA

ISO9001Certified

Battery Installation

WARNING: To avoid electric shock, always turn off the power and

disconnect the test leads before opening the back to replace the fuse or

battery.

1. Remove the screws securing the rear cover using a Phillips head

screwdriver.

2. Lift the cover off and replace the battery observing the correct polarity.

3. Insert the new battery into the battery holder.

Replace the rear cover and secure with the screws. WARNING: To avoid

electric shock, do not operate the meter until the battery cover is in place

and fastened securely.

NOTE: If your meter does not work properly, check the fuses and battery to

make sure that they are still good and that they are properly inserted.

Operating Instructions

WARNING: Risk of electrocution. High-voltage circuits, both AC and DC, are

very dangerous and should be measured with great care.

1. ALWAYS turn the function switch to the OFF position when the meter is not

in use.

DC VOLTAGE MEASUREMENTS

CAUTION: Do not measure DC voltages if a motor on the circuit is being

switched ON or OFF. Large voltage surges may occur that can damage

the meter.

1. Set the function switch to the highest V DC position.

2. Insert the black test lead banana plug into the

negative (COM) jack.

Insert the red test lead banana plug into the positive

(V) jack.

3. Touch the black test probe tip to the negative side of

the circuit.

Touch the red test probe tip to the positive side of the

circuit.

4. Read the voltage in the display. Reset the function

switch to successively lower V DC positions to obtain

a higher scale reading.

DC CURRENT MEASUREMENTS

1. Insert the black test lead banana plug into the negative

(COM) jack.

2. Set the function switch to the 250mA DC position and

insert the red test lead banana plug into the (mA) jack.

3. Remove power from the circuit under test, then open up

the circuit at the point where you wish to measure

current.

4. Touch the black test probe tip to the negative side of

the circuit.

Touch the red test probe tip to the positive side of the

circuit.

5. Apply power to the circuit.

6. Read the current in the display. Reset the function

switch to successively lower mA positions to obtain a higher scale reading.

AC VOLTAGE MEASUREMENT

WARNING: Risk of Electrocution. The probe tips may not be long enough

to contact the live parts inside some 240V outlets for appliances because

the contacts are recessed deep in the outlets. As a result, the reading may

show 0 volts when the outlet actually has voltage on it. Make sure the

probe tips are touching the metal contacts inside the outlet before

assuming that no voltage is present.

CAUTION: Do not measure AC voltages if a motor on the circuit is being

switched ON or OFF. Large voltage surges may occur that can damage

the meter.

1. Set the function switch to the highest V AC position.

2. Insert the black test lead banana plug into the

negative (COM) jack.

Insert red test lead banana plug into the positive (V)

jack.

3. Touch the black test probe tip to the negative side

of the circuit.

Touch the red test probe tip to the positive side of

the circuit.

4. Read the voltage in the display. Reset the function

switch to successively lower V AC positions to

obtain a higher scale reading.

RESISTANCE MEASUREMENTS

WARNING: To avoid electric shock, disconnect power to the unit under

test and discharge all capacitors before taking any resistance

measurements. Remove the batteries and unplug the line cords.

1. Set the function switch to the X10 or X1K position.

2. Insert the black test lead banana plug into the negative

(COM) jack

Insert the red test lead banana plug into the positive 

jack.

3. Touch the test probe tips together and adjust the OHM

Zero Adjust knob for a “0” reading.

4. Touch the test probe tips across the circuit or part under

test. It is best to disconnect one side of the part under

test so the rest of the circuit will not interfere with the

resistance reading.

5. Read the resistance on the scale

dB MEASUREMENTS

The dB scale can be used to measure the milliwatt power dissipation on a

600Ω load by measuring the voltage across a 600 Ω load. An AC voltage of

0.775Vrms across 600Ω is equal to 1mW or “0”dB When converting an AC

Voltage measurement to dB take the dB reading from the lowest arc on the

scale plate and then add the appropriate dB correction found in the table

below.

ACV ADD dB

10 0 -10 ~ 22

50 14 4 ~ 36

250 28 18 ~ 50

500 34 24 ~ 56

Maintenance

WARNING: To avoid electric

source of voltage before rem

covers.

WARNING: To avoid electric

battery and fuse covers are

This MultiMeter is designed to

following care instructions are

1. KEEP THE METER DRY

2. USE AND STORE THE

Temperature extremes c

distort or melt plastic pa

3. HANDLE THE METER

damage the electronic p

4. KEEP THE METER CLE

cloth. DO NOT use chem

5. USE ONLY FRESH BAT

TYPE. Remove old or w

unit.

6. IF THE METER IS TO B

the batteries should be r

UL LISTED

The UL mark does not indicat

accuracy of its readings.

Warranty

FLIRSystems,Inc.warrantsthis

inpartsand workmanship  for on

warranty sensorsappliesto and

instrumentforservice  during or b

Service Department forauthoriza

information. Return AAuthoriza

returned.Thesenderisresponsib

packagingtopreventdamagein

resultingfrom    action of the user

specification,impropermaintena

Systems,Inc.specificallydisclaim

for a specificpurposeandwillno

consequentialdamages.FLIR’sto

product.Thewarrantysetfortha

writtenororal,isexpressedorim

Calibration,Repair,a

FLIRSystems,Inc.offersrepaira

productswesell.NISTcertificati

CustomerServiceDepartmentfo

product.Annualcalibrationssho

accuracy. Technical supportand

contactinformationprovidedbe

Allrightsreservedincludingthe

Produkt Specifikationer

Mærke:	Extech
Kategori:	Multimeter
Model:	38070

Har du brug for hjælp?

Hvis du har brug for hjælp til Extech 38070 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Multimeter Extech Manualer

22 December 2024

28 August 2024

27 August 2024

27 August 2024

27 August 2024

23 August 2024

17 August 2024

14 August 2024

13 August 2024

12 August 2024

Multimeter Manualer

Nyeste Multimeter Manualer

8 Juni 2025

7 Juni 2025

7 Juni 2025

6 Juni 2025

6 Juni 2025

6 Juni 2025

6 Juni 2025

6 Juni 2025

6 Juni 2025

3 Juni 2025