Extron ACP 100 Manual
Extron
Ikke kategoriseret
ACP 100
Læs gratis den danske manual til Extron ACP 100 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Extron ACP 100, eller vil du spørge andre brugere om produktet?
Side 1/8
1
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
ACP 100 • Setup Guide
The Extron ACP 100 Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled device.
Each ACP 100 includes two ACP ports, which support both power and communication between the host device and the
ACP100. Up to eight ACP panels can be used per host device for more demanding control needs.
Front Panel Features
MIC
SOURCE
1
PROGRAM
MUTE
SOURCE
3
SOURCE
2
MIC PROGRAM
SOURCE
1
RCE
TE
RCE
E
RESET
ACP 100 Front Panel with Plastic
Faceplate
ACP 100 Front Panel without
Plastic Faceplate
EEEE
CCCC
BBBB
AAAA
DDDDFFFF
Figure 1. ACP 100 Front Panel
Rear Panel Features
PWR LOAD = 0.5W
BUS ID
M
S
B
L
S
B
ON
1 2 3 4 5 6
ID
ERROR
S TAT U S
LINK
COM
ERROR
ID
ERROR
S T AT U S
LINK
COM
ERROR
ACP
G
-
S+S+V G
-
S+S+V
ACP 100 Rear Panel
CCCC
BBBB
AAAA
Figure 2. ACP 100 Rear Panel
Planning the System and Installation
When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see
the ACP 100 product page at www.extron.com for more information about the ACP 100).
A Plastic Faceplate
B Function Buttons 1 and 2
C Function Buttons 3-6
D Volume LEDs and Knob
E Mounting Holes (4)
F Reset Button
A Bus ID DIP Switches
B ACP Ports (2)
C ACP Status LEDs
2
ACP 100 • Setup Guide (Continued)
Installation
Step 1: Get Ready
Use the following checklist to prepare for the installation:
Download and install the latest version of software, rmware, and device drivers needed to congure the host device and
congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on
software and drivers).
Obtain cables, mounting hardware, and any other supplies required for ACP 100 installation.
Step 2: Prepare the Installation Site
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Extron recommends installing the ACP 100 into a grounded, UL Listed electrical junction box.
• Extron recommande d’installer le ACP 100 dans un boîtier d’encastrement électrique mis à la terre, listé UL.
• If the ACP 100 will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access hole
and perform the physical installation so the surface will not be damaged.
• S’il est prévu d’installer le ACP 100 dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié
pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.
• Follow all national and local building and electrical codes that apply to the installation site.
• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.
NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 100 must
be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the
ACP100.
Americans with Disabilities ACT (ADA) Compliance
When planning where to install these devices, consider factors affecting accessibility of the button panel such as height
from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections
307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the available at 2010 ADA Standards for Accessible Design
http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.
Site Preparation
Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external
wall boxes (EWBs), and surface or tabletop mounting boxes for use with the ACP button
panels. The ACP 100 is a US 2-gang size device.
Step 3: Replace Plastic Faceplate, Button Labels, or
Knob
The plastic faceplate button labels can be replaced. Some
button labels ship with the unit. Customized labels can be
created and printed using Extron Button Label Generator
software from www.extron.com.
To change a plastic faceplate or translucent button label:
1. The plastic faceplate is secured with four magnetic
catches on the underside of the plastic faceplate.
Remove the plastic faceplate by holding the body of
the unit with one hand, gripping the sides of the plastic
faceplate with the other hand, then pulling the plastic
faceplate away from the unit.
2. Gently separate the button lens cap from its white
diffuser. Insert the end of the provided Extron removal (pry) tool into the corner notch
and gently twist the tool (see 1 in the image to the right).
TEXT
Separate the
two-piece button
her
e at the corner.
Dif
fuser
Base
Insert
button label.
Button
Lens Cap
Removal
(Pry) Tool
1
2
Produkt Specifikationer
| Mærke: | Extron |
| Kategori: | Ikke kategoriseret |
| Model: | ACP 100 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Extron ACP 100 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Extron Manualer
14 Juni 2025
11 Marts 2025
10 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
3 Januar 2025
Ikke kategoriseret Manualer
- Godox
- Soundmaster
- Pinolino
- Megarevo
- Hartke
- Tesy
- Dali
- Ledlenser
- Skaarhoj
- Bugera
- Gamesir
- Bushnell
- Samlex
- Challenge Xtreme
- Idec
Nyeste Ikke kategoriseret Manualer
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025