Extron ACP 106 D Manual

Extron Ikke kategoriseret ACP 106 D

Læs gratis den danske manual til Extron ACP 106 D (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Extron ACP 106 D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 106 D • Setup Guide

The Extron ACP 106 D Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled device.

Each ACP 106 D includes two ACP ports, which support power and communication between the host device and the ACP 106 D.

Up to eight ACP panels can be used per host device for more demanding control needs.

Front Panel Features

ExtronExtron

PROGRAM

MIC

VOLUME

MUTE

G G

A Mute Buttons

B Transmit LED

C Volume Buttons

D Volume LED Meter

E Function Button 1

F Function Button 2

Figure 1. ACP 106 D Rear Panel

Rear Panel Features

ACP

PWR LOAD = 1.5W

+S -S G +V +S -S G

STAT US

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

A ACP Ports (2)

B Connection Status LED

C Reset Button

D Bus ID DIP Switches

Figure 2. ACP 106 D Front Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see the

ACP 106 D product page at www.extron.com for more information about the ACP 106 D).

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 106 D installation.

ACP 106 D • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 106 D into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 106 D dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 106 D will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access

hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 106 D dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualifié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 106 D must

be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the

ACP106 D.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the available at 2010 ADA Standards for Accessible Design

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP 106 D is a US 1-gang size device.

Step 3: Removing the Plastic Faceplate, Button Panel, and Changing the Buttons

The plastic faceplate and buttons can be replaced. Additional buttons ship with the

device and others can be ordered from www.extron.com.

To change the buttons:

1. Remove the two screws holding the plastic faceplate to the metal mounting

plate and separate the faceplate from the button plate (see 1 in the gure to

the right).

2. Insert a small at-bladed screw driver into the notch at the top of the button

plate. Release the catch holding the button plate to the metal mounting plate

(2).

3. Repeat step 2 to release the catch at the bottom of the plate.

4. Tilt the top of the button plate forward as it is removed to prevent the buttons

from falling out.

Extron

VOLUME

MUTE

MIC

PROGRAM

ACP 106 D

Face plate

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	ACP 106 D

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron ACP 106 D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Extron Manualer

Extron DTP3 IN2004 Manual

14 Juni 2025

Extron CPM 103 Manual

11 Marts 2025

Extron IN1608 XI Manual

10 Januar 2025

Extron ZipClip 100 Manual

3 Januar 2025

Extron HC 402 Manual

3 Januar 2025

Extron ShareLink Pro 2500 Manual

3 Januar 2025

Extron FOX3 SR 301 Manual

3 Januar 2025

Extron TMK 110 D Manual

3 Januar 2025

Extron SMB 210 Manual

3 Januar 2025

Extron FOX3 T 201 Manual

3 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025