Extron ACP 106 EU Manual

Extron Ikke kategoriseret ACP 106 EU

Læs gratis den danske manual til Extron ACP 106 EU (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Extron ACP 106 EU, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 106 EU/MK • Setup Guide

The Extron ACP 106 EU/MK Audio Control Panels are fully congurable control interfaces for use with any Extron ACP-enabled

device.

Each ACP 106 EU/MK includes two ACP ports, which support power and communication between the host device and the

ACP 106 EU/MK. Up to eight ACP panels can be used per host device for more demanding control needs.

NOTE: The ACP 106 EU front and rear panels are identical to those of the ACP 106 MK. The only difference is the shape of

the plastic faceplate attached to the front of the device. The panels function identically.

Front Panel Features

VOLUME

MUTE

PROGRAM

MIC

Extron

Figure 1. ACP 106 EU Front Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP 106 EU and ACP 106 MK product pages at www.extron.com for more information about the ACP 106 EU/MK).

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 106 EU and MK installation.

Figure 2. ACP 106 EU Rear Panel

ACP

PWR LOAD

= 1.5W

+S -S G +V S - G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Rear Panel Features

A ACP Ports (2)

B Connection Status LED

C Reset Button

D Bus ID DIP Switches

A Mute Buttons

B Transmit LED

C Volume Buttons

D Volume LED Meter

E Function Button 1

F Function Button 2

ACP 106 EU/MK • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 106 EU/MK into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 106 EU/MK dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 106 EU/MK will be installed into ne furniture, it is best to hire a licensed, bonded craftsperson to cut the

access hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 106 EU/MK dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 106 EU/MK

must be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with

the ACP106 D.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the available at 2010 ADA Standards for Accessible Design

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP 106 EU and ACP 106 MK are 1-gang EU and MK size

devices.

Step 3: Removing the Plastic Faceplate, Button Panel, and Changing

the Buttons

The plastic faceplate and buttons can be replaced. Additional buttons ship with the device and

others can be ordered from www.extron.com.

To change the buttons:

1. Insert the Extron removal tool (pry tool) between one side of the plastic faceplate and the

button plate. Release the catch holding the wallplate to the metal mounting plate (see 1

in the gure to the right). If necessary, use the pry tool to release the second catch on the

opposite side.

2. To separate the button plate from the control plate, insert a small at-bladed screw driver

into one of the slots (see 2 in the gure at the bottom of the page).

3. Press the blade of the screw driver in until there is an audible

click and the tab is pushed out of the slot.

4. Repeat steps 2 and 3 to release all four tabs holding the button

plate in place.

5. Tilt the top of the button plate forward as it is removed to

prevent the buttons from falling out (3).

VOLUME

MUTE

MIC

PROGRAM

VOLUME

MUTE

MIC

PROGRAM

Extr onExtr on

Insert

to lin

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	ACP 106 EU
Bredde:	81 mm
Dybde:	10 mm
Højde:	81 mm
Vægt:	100 g
Produktfarve:	Black, White
Materiale:	Metal, Plastic
Antal poler:	4P