Extron ACP VC1 EU Manual

Extron Ikke kategoriseret ACP VC1 EU

Læs gratis den danske manual til Extron ACP VC1 EU (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 69 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 35 anmeldelser. Har du et spørgsmål om Extron ACP VC1 EU, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP VC1 EU/MK • Setup Guide

The Extron ACP VC1 EU/MK Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled

device.

Each ACP VC1 EU/MK includes two ACP ports, which support power and communication between the host device and the

ACP VC1 EU/MK. Up to eight ACP panels can be used per host device for more demanding control needs.

NOTE: The ACP VC1 EU front and rear panels are identical to those of the ACP VC1 MK. The only difference is the shape of

the plastic faceplate attached to the front of the device. The panels function identically.

Planning System Installation

When planning an ACP system installation, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP VC1 EU and ACP VC1 MK product pages at www.extron.com for more information regarding the ACP VC1 EU/MK).

Front and Rear Panel Features

ACP

PWR LOAD

= 1.5W

+S -S G +V - G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Figure 1. ACP VC1 EU/MK

A Front Panel Rotary Volume Knob D Connection Status LED

B Front Panel Button E Reset Button

C ACP Ports (2) F Bus ID DIP Switches

Installation

Step 1: Get Ready

Use the following checklist to prepare for installation:

Download and install the latest software, rmware, and device drivers needed to congure the host device and the

connected ACP devices (see the host device user guide, available at www.extron.com, for details regarding software and

drivers).

Obtain cables, mounting hardware, and any other supplies required for the installation.

ACP VC1 EU/MK • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP VC1 EU/MK into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP VC1 EU/MK dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP VC1 EU/MK will be installed into ne furniture, it is best to hire a licensed, bonded craftsperson to cut the

access hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP VC1 EU/MK dans du beau mobilier, il est préférable de faire appel à un artisan autorisé

et qualié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and comply with National Electrical Code (NEC), the ACP VC1 EU/MK

must be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with

the ACP VC1 EU/MK.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height from

the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections 307

(“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 available at ADA Standards for Accessible Design

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP VC1 EU and ACP VC1 MK are 1-gang EU and MK size

devices.

Step 3: Removing the Plastic Faceplate, Removing the Button Panel, and Changing the Button

The plastic faceplate and button can be replaced. Additional buttons ship with the device and others can be ordered from

www.extron.com.

To change the button:

1. Insert the Extron removal tool (pry tool) between one side of the plastic faceplate and

the button plate. Release the catch holding the wallplate to the metal mounting plate

(see 1 in the figure to the right). If necessary, use the pry tool to release the second

catch on the opposite side.

2. Insert a small flat-bladed screw driver into a slot on the button plate to separate the

button plate from the control plate (2).

3. Press the blade of the screw driver in until there is an audible click.

4. Repeat steps 2 and 3 to release all four tabs holding the button plate in place.

5. Tilt the top of the button plate forward as it is removed to prevent the button from

falling out (3).

6. To remove the button, press the button backward through its

MUTE

ExtronExtron

Insert

to line.

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	ACP VC1 EU
Type:	Digital volumenkontrol
Vægt:	100 g
Produktfarve:	Black, White
Pakkevægt:	200 g
Pakkedybde:	178 mm
Pakkebredde:	102 mm
Pakkehøjde:	76 mm
Strømforbrug (typisk):	1 W
Husmateriale:	Plast
Monteringstype:	Vægmonteret
Indgående driftsspænding (maks.):	12 V
Effekthåndtering:	- W
Dæmpningsknap:	Ja
Faceplate åbningsdimensioner (BxH):	81 x 81 mm