Extron Cable Cubby F55 UT Manual

Extron Ikke kategoriseret Cable Cubby F55 UT

Læs gratis den danske manual til Extron Cable Cubby F55 UT (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Extron Cable Cubby F55 UT, eller vil du spørge andre brugere om produktet?

Side 1/6
1
Retractor for Cable Cubby F55 UT •
Installation Guide
This guide provides instructions for an experienced technician
to install the Extron Retractor for the CableCubby® F55 UT
Enclosure.
Additional instructions are available in the user guide for the
Cable Cubby F55 UT Enclosure at www.extron.com.
NOTE: For information on safety guidelines, regulatory
compliances, EMI/EMF compatibility, accessibility, and
related topics, see the Extron Safety and Regulatory
Compliance Guide on the Extron website.
Planning
The retractor modules can be mounted inward or outward
depending on available under‑table clearance and accessibility.
Up to two retractor modules can be installed per enclosure.
NOTE: Inward mounting is recommended for installations with
limited clearance.
For new installations, to determine the best location for the
enclosure, keep in mind the under‑table space required for the
retractor modules (see Determining Under-table Clearance for
more info).
Required Tools and Additional Accessories
Thumb
Sc wre
Two 1/4"-20 Screws
Retractor
Bracket
Support Bracket
Flex55
Adapter
Module
Retractor
bezel
Tape Measure
Phillips Screw Driver
Zip Ties
Marker Pen
#6 x 1/2"
Wood Screw
Figure 1. Tools and Accessories
Determining Under-table Clearance
The diagram on the following page shows the space required for a retractor module installation in a Cable Cubby F55 UT
enclosure.
NOTES:
To prevent objects from impeding cable retraction, ensure the exposed cable clears nearby obstructions.
Excess cabling can cause clearance issues. Use zip ties to secure under‑table cabling to prevent accidental contact or
entanglement with users.
IMPORTANT:
I
I
I
IM
M
M
MP
P
P
PO
O
O
ORT
RT
RT
RTA
A
A
AN
N
N
NT:
T:
T:
T:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
Inwa Installrd
(Final Assembly)
Outward Install
(Final Assembly)
2
Retractor for Cable Cubby F55 UT • Installation Guide (Continued)
Mounting Orientations and Dimensions
The following diagrams illustrate the mounting dimensions for outward, double outward, and inward retractor module orientations.
Outward Installation
Double Outward Installation
Inward Installation
8.55"
(21.7 cm)
18.40"
(46.73 cm)
39.36"
(99.98 cm)
24.95"
(63.38 cm)
8.55"
(21.7 cm)
8.55"
(21.7 cm)
FRONT
REAR
FRONT
REAR
FRONT
REAR
Figure 2. Cable Cubby F55 UT with Retractor Modules - Mounting Orientations and Dimensions
Preparing the Enclosure
Ensure the retractor has adequate under‑table clearance for installation (see previous section). You should have the required
accessories for mounting the retractor and to congure the enclosure.
CAUTION: Disconnect the power from the Cable Cubby enclosure before beginning a retractor system installation.
ATTENTION : Débranchez l’alimentation du boîtier CableCubby avant de commencer l’installation d’un système de
rétracteur.


Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: Cable Cubby F55 UT

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron Cable Cubby F55 UT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Extron Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer