Extron DTP3 T 301 Manual


Læs gratis den danske manual til Extron DTP3 T 301 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Extron DTP3 T 301, eller vil du spørge andre brugere om produktet?

Side 1/4
1
IMPORTANT:
I
I
I
IM
M
M
MP
P
P
PO
O
O
ORT
RT
RT
RTA
A
A
AN
N
N
NT:
T:
T:
T:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP3 T/R 301 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up
and operate the DTP3 T 301 transmitter and DTP3 R 301 receiver. These DTP3
digital video Extenders can extend the following up to 330feet (100meters), using shielded twisted pair cabling:
HDMI digital video signal to 4K@60Hz (4:4:4) (can include embedded digital audio)
Optional analog audio USB HID & 2.0
Bidirectional RS‑232 control Remote power (receiver to transmitter)
NOTE: Maximum transmission distances vary with resolutions used, cable types, and environment (see the
DTP3T/R301UserGuide at www.extron.com for full specifications).
POWER
1.0 A MAX
12V
DTP 3 IN
SIG LINK
RS- 232
Tx R x G
OVER DT P3
SEN D
PWR
OFF AUD IO
L R
R
DEVIC ES
USB HID
USB 2.0
HDMI
OUTP UT S
3
4
1
2
POWER
2.8 MAX
12V
DTP 3 OUT
SIG LINK
RS- 232
Tx R x G
OVER DTP3
AUDIO H OST
R
BA
HDMIHDMI
OUTP UT S
INPU T S
POWER STANDB Y
Table
Microphone
Camera
Comput
er
75" h D yTouc ispla
CAT6A Cable
up to 330' (100 m)
USB
USB
4K/60
HDMI
4K/60
HDMI
Audi
o
USB
USB
Extron
SB 33 A 75-80
S d roun Ba
Extron
DTP3 R 301
Receiver
Extron
DTP3 T 301
Tra rnsmitte
Figure 1. Typical DTP3 T/R 301 Transmitter and Receiver Application
Installation
Turn off and disconnect all equipment power sources and mount the transmitter and receiver Extender units as required. The
units can be mounted in a variety of locations using optional Extron mounting accessories (see www.extron.com to determine
the compatible mounting options).
Rear Panel Connections
POWER
1.0 A MAX
12V
DTP3 IN
SIG LINK
RS-232
Tx Rx G
OVER DTP3
SEND
PWR
OFF AUDIO
L R
R
DEVICES
USB HID
USB 2.0
HDMI
OUTPUTS
3
4
1
2
LLLIII MMM KKK
JJJ OOO
POWER
2.8 A MAX
12V
DTP3 OUT
SIG LINK
RS-232
Tx Rx G
OVER DTP3
AUDIO
DTP3 T 301
DTP3 R 301
HOST
R
BA
HDMIHDMI
OUTPUTS
INPUTS
AAA FFF EEEBB
B H
HHCC
C D
DD
NNN
GGG
Figure 2. DTP3 T/R 301 Rear Panel Connectors and Features
2
Transmitter Features
A HDMI input port (see figure 2 on page 1) — Connect an HDMI cable between this port and the HDMI output
HDMI
port (or DVI port, with an appropriate adapter) of the digital video source. The transmitter also accepts embedded
digital audio on this port.
NOTE: See LockIt™ Lacing Brackets on page 3 to use the included Extron LockIt HDMI Cable Lacing
Bracket to secure the connector to the transmitter for A and E.
B Audio input connector — If desired, plug an analog audio input into the transmitter via this stereo mini jack.
AUDIO
NOTE: The analog audio input is in addition to the digital audio that may be embedded in the HDMI input.
C USB Host input port — Connect a USB Type A to B cable between this USB type B port and the USB port of a
HOST
host device.
D Over DTP3 port — Connect a serial RS‑232 signal to this 3.5 mm, 3‑pole captive screw connector for
RS-232
Tx Rx G
OVER DTP3
bidirectional RS‑232 (see on page 4 to wire the connector).
Over DTP3 connector port
E HDMI output port — Connect a display to this female HDMI connector for local loop‑through monitoring of the
HDMI
source signal.
F — Connect one end of a TP cable to this RJ‑45 female connector. Ensure the opposite DTP3 OUT (TP) port
DTP3 OUT
end of this cable is connected to the receiver TP Input port (see I, below).
Use Extron XTP DTP 22 STP cable for the best performance. At minimum, Extron recommends 22 AWG,
solid conductor, STP cable with a minimum bandwidth of 500 MHz.
Terminate cables with sheilded connectors to the TIA/EIA‑T568B standard (see on page 4).DTP3 (TP) port
Limit the use of more than two pass‑through points, which may include patch points, and punch down connectors. If
these pass‑through points are required, use shielded couplers and punch down connectors.
ATTENTION:
Do not connect these devices to a telecommunications or computer data network.
Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
Signal LED — Indicates the unit is outputting a DTP3 signal.
Link LED — Indicates a valid link is established between the units on the DTP3 input and output cable.
G Power connector (required, if receiver, I, is not sending power ) — Plug an optional external 12 VDC power
POWER
2.8 A MA
X
12V
supply into this 2‑pole connector (see on page 4).
Power port
ATTENTION:
Do not connect any external power supplies until you have read the Attention notications in the Power
Supply section of the .DTP3 T/R 301 User Guide
Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section «
Power Supply » du .DTP3 T/R 301 User Guide
H RESET button and LED This button initiates two levels of reset (see the , at DTP3 T/R 301 User Guide www.extron.com).
Receiver Features
DTP3 IN
SIG LINK
SEND
PWR
OFF
I — Connect one end of the TP cable from the transmitter DTP3 IN (TP) port and Send PWR switch
output connector to this RJ‑45 female connector. Ensure the opposite end of this cable is connected to
the Output RJ‑45 connector on a compatible transmitter.


Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: DTP3 T 301

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron DTP3 T 301 stil et spørgsmål nedenfor, og andre brugere vil svare dig