Extron EWB Series Manual

Extron Ikke kategoriseret EWB Series

Læs gratis den danske manual til Extron EWB Series (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Extron EWB Series, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1
EWB Series External Wall Boxes • Installation Guide
The Extron EWB Series External Wall Boxes allow a variety of Extron products to be mounted to the surface of an interior
wall. The 2.5 inch (6.4 cm) depth accomodates an Extron product and cabling. This guide provides information for a
qualified, experienced installer to install an EWB wall box.
EWB External Wall Box Models
EWB 104
4-gang EWB
EWB 105
5-gang EWB
EWB 103
3-gang EWB
EWB 102
2-gang EWB
EWB 101
1-gang EWB
Recommended Fasteners
Choose the appropriate type of screw or bolt for the wall (see table below). The mounting holes in the back of the EWB
accommodate screws up to ¼ inch in diameter.
Wall Type Fasteners Min. Size Fastener
Quantity
Drill Bit Size Notes
Drywall Toggle bolts 3/16 inch At least 4 1/2 inch Min. 3/8 inch wall thickness
Solid wood Wood screws #10 with a washer At least 4 Not required Min. 3/8 inch wall thickness
Masonry Masonry screws 1/4 inch At least 4 3/16 inch masonry bit Do not mount to masonry joints.
Grounding
The rear inside panel has a PEM® #6‑32 insert for grounding; a grounding screw is included with each EWB.
Mounting the EWB
NOTES: This unit must be installed in accordance with the National Electrical Code and with all local codes.
Ensure that the installation meets the local and state regulatory requirements, including building,
electrical, and safety codes, and UL and ADA accessibility requirements.
Ensure that there are no utility cables or pipes at the intended location that might be damaged or cause
injury when installing the wall box.
The EWB can be mounted on any interior wall type. Knockouts allow for conduit or raceways to be run from the top,
bottom, or back of the box. Install the cables into the wall or conduits before mounting the EWB wall
box or installing any devices in the EWB. The installation instructions apply to all models.
Model Part Number
EWB 101 (black, white) 60‑1161‑02, ‑03
EWB 102 (black, white) 60‑1162‑02, ‑03
EWB 103 (black, white) 60‑1163‑02, ‑03
EWB 104 (black, white) 60‑1164‑02, ‑03
EWB 105 (black, white) 60‑1165‑02, ‑03
Surface Raceway Knockouts
Size Dimensions Quantity
per EWB
Small 0.9” H x 0.75” W
(2.3 cm H x 1.9 cm W)
2
Large 0.95" H x 2.0" W
(2.4 cm H x 5.1 cm W)
2
Mounting
Screws )(4
4
Installing the EWB Onto a Wall
1. If mounting to standard wood wall studs, locate the center of the studs.
2. Place the EWB against the wall in a suitable location. Use a level to ensure the box is
horizontal, and mark the position of the four holes.
3. If required, drill four holes into the wall.
4. Insert four screws (see the table above) and attach the EWB to the wall.
1
1
1..
1.
1
2
EWB Series External Wall Boxes • Installation Guide (Continued)
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Attaching the EWB to an Existing In-wall Junction Box
This procedure is to be used if a standard electrical junction box
is already installed in the wall.
If a junction box is not already installed, follow the instructions
in “Installing the EWB Onto a Wall.“
NOTE: The size of the in‑wall junction box does not
have to match the size of the EWB as long as
the junction box is not larger than the EWB.
Mount the EWB to an existing junction box as follows:
1. Align the EWB with the opening of the junction box. Center
the EWB in front of the junction box if possible.
2. Attach the EWB to the junction box using #6‑32 pan head
screws (not included) (see figure 1).
Figure 1. Mounting the EWB to an In-wall Junction Box
68-649-02
Rev. B
08 11

Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: EWB Series

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron EWB Series stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Extron Manualer

Extron

Extron DTP3 IN2004 Manual

14 Juni 2025
Extron

Extron CPM 103 Manual

11 Marts 2025
Extron

Extron IN1608 XI Manual

10 Januar 2025
Extron

Extron ZipClip 100 Manual

3 Januar 2025
Extron

Extron HC 402 Manual

3 Januar 2025
Extron

Extron ShareLink Pro 2500 Manual

3 Januar 2025
Extron

Extron FOX3 SR 301 Manual

3 Januar 2025
Extron

Extron TMK 110 D Manual

3 Januar 2025
Extron

Extron SMB 210 Manual

3 Januar 2025
Extron

Extron FOX3 T 201 Manual

3 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Sony

Sony RM-V202T Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Attax Metroverb Manual

15 Juni 2025
Kohler

Kohler K-10124 Manual

15 Juni 2025
Planet Audio

Planet Audio P9900CPA Manual

15 Juni 2025
Levenhuk

Levenhuk LabZZ SP20 Manual

15 Juni 2025
Planet Audio

Planet Audio P62CP Manual

15 Juni 2025
Cranborne Audio

Cranborne Audio Carnaby 500 Manual

15 Juni 2025
Audio-Technica

Audio-Technica AT-VM740xML/H Manual

15 Juni 2025
Stamos

Stamos SWG-WC-3D Manual

15 Juni 2025
Planet Audio

Planet Audio P350MB Manual

15 Juni 2025