Extron IPA T RLY4 Manual

Extron Ikke kategoriseret IPA T RLY4

Læs gratis den danske manual til Extron IPA T RLY4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Extron IPA T RLY4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

IMPORTANT:

ORT

RTA

NT:

Go to www.extron.com for the

complete product specifications.

IPA T RLY4 • Setup Guide

This guide provides instructions for an experienced installer to install the Extron IPA T RLY4 relay accessory and to make all

connections.

The IPA T RLY4 is an IPLink® Accessory product. The relay accessory consists of four output relays with normally open (when the

relay is de-energized) (NO) and normally closed (NC) contacts.

The relay accessory converts a solid state (up to 12 VDC) signal, from a Flex I/O port or Digital I/O port on an Extron control

processor, to a relay contact closure. The relay contacts can handle up to 24 VAC or 24 VDC as a tally signal, contact closure

signal, or control signal to drive devices in your system, such as a lighting system (see gure 1) or remote screens. The relay

contacts are protected by an overvoltage circuit.

The compact IPA T RLY4 can be concealed out of the way anywhere in your system with the included hook and loop fastener strip.

IPA T RLY4

1 2 3 4 C

INPUT S

PWR OUT = 6W

V C G

VOL

PO WER

12V

1.0A MAX

T x Rx

RT S CT S

CO M 1

1 2 4 G

DI GIT AL I/O

T x R x

CO M 2

-S+V +S G

eB US

C1 2

RE L AY S

IR /S

LAN

Extron

IPCP Pro 255Q xi

Ethernet Control

Processor

Extron

IPA T RLY4

Relay Accessory

NO C NC NO C NC NO C NC NO C NC

RELAY 1 RELAY 2 REL AY 3 RELAY 4

Lighting System

Front

Rear

Extron

12 V Power

Supply

+12 VDC

(Common)

Figure 1. Typical IPA T RLY 4 Application

Connections

NOTE: The 5-pole captive screw input connector and four 3-pole captive screw output connectors are included with the

unit, but you must supply the cable. Extron recommends the CTL Series cable, available non-plenum and plenum bulk

rolls and plenum pre-cut lengths.

IPA T RLY4 1 2 3 4 C

INPUTS

NO C NC NO C NC NO C NC NO C NC

RELAY 1 RELAY 2 RELAY 3 RELAY 4

BB BB BB BB

Figure 2. IPA T RLY4 Connections

Input Connections

A — Connect the 12 VDC source to the common voltage (C) terminal of the 5-pole captive screw Inputs

connector. Connect the appropriate terminal (1 though 4) to the digital output or flex I/O of the Extron control

processor.

IPA T RLY4 • Setup Guide (Continued)

ATTENTION:

• Connect +12 VDC to the C pin only and connect the return to one or all of the Input pins (1 through 4) for the relays that

you will use. Reversing the connections can damage the power supply.

• Raccordez une source +12Vcc uniquement à la broche C du connecteur et raccordez le circuit de retour à une ou

plusieurs broches d’entrée (1 à 4) pour les relais utilisés. Inverser les raccordements pourrait endommager la source

d’alimentation.

• Observe proper polarity when making connections to the Power port on the MLC 104 IP Plus controller. Miswiring can

damage the port.

• Veillez à respecter la polarité appropriée lorsque vous effectuez des raccordements au port d’alimentation du

contrôleur MLC 104 IP Plus. Une erreur de raccordement pourrait endommager le port.

NOTES:

• Connect the I/O control line to the Input 1 terminal for relay 1, Input 2 for relay 2, and so on.

• Figure 3 is a wiring diagram of a typical application: an Extron MLC 104 IP Plus controlling an IPA T RLY4 relay function

(see the for information on conguring the MLC to control the IPA T RLY4).MLC 104 Plus Series User Guide

• Figure 4 shows an application that includes an external power supply and an Extron IPCP Pro Dual-NIC Controller.

When the relay accessory is connected to an IO port of an IPCP Pro module, ground the external power supply to the

IO port ground pin on the control processor.

IPA T RLY4 1 2 3 4 C

INPUTS

G R O U N D

+ 1 2V O UT

C M

G R O U N D

I R O U T

G R O U N D

S C P

G R O U N D

T x

DISPLAY

RS-232/IR

A B C D E

COMM LINK

LAN

PRESS TAB WITH

TWEEKER TO REM EOV

A B

MLS

RS-232

POWER

12V

DIGI LTA

I/O

IR I N

T x

GRO UN D

+1 2V IN

MLC 104 IP Plus

Right Side

IPA T RLY4

Front Panel

+12 VDC

Relay 1

Relay 2

Relay 3

Figure 3. Wiring Diagram for Connection to an MLC 104 IP Plus

LAN

GTx Rx GTx Rx

COM 2 COM 3

RELAYS

21 43 CC

COM 1

GTx Rx

RTS CTS

IR/SERIAL

S G

1 2 3 4 G

DIGITAL I/O

BUS

AV LAN 2

AV LAN 1

AV LAN 3

IPA T RLY4 1 2 3 4 C

NPUT

Ground

all devices

– Return

+12 VDC input

Ridged

Smooth

AX 50-6 0Hz

External

12 VDC

Power Supply

21 3 4

I PCP Pro Control r Processo with Internal Power Supply

ithin another )device

IPA T RLY4

Figure 4. Wiring Diagram for Connection to an IPCP Pro Control Processor with Internal Power Supply

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	IPA T RLY4

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron IPA T RLY4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Extron Manualer

Extron DTP3 IN2004 Manual

14 Juni 2025

Extron CPM 103 Manual

11 Marts 2025

Extron IN1608 XI Manual

10 Januar 2025

Extron ZipClip 100 Manual

3 Januar 2025

Extron HC 402 Manual

3 Januar 2025

Extron ShareLink Pro 2500 Manual

3 Januar 2025

Extron FOX3 SR 301 Manual

3 Januar 2025

Extron TMK 110 D Manual

3 Januar 2025

Extron SMB 210 Manual

3 Januar 2025

Extron FOX3 T 201 Manual

3 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025