Extron KNX 100G Manual

Extron Ikke kategoriseret KNX 100G

Læs gratis den danske manual til Extron KNX 100G (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Extron KNX 100G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

KNX 100G • Setup Guide

This setup guide covers the physical installation of the KNX 100G and KNXnet/IP tunneling from a PC to a KNX network during

conguration and commissioning.

The KNX 100G allows better integration of control with KNX building management systems (BMS). The product serves as a

gateway for control systems and ETS software to the KNX bus, and it is designed to be installed onto a DIN rail with a width of 1

unit (18 mm).

Power is supplied via the KNX bus; an external power supply is not necessary. The KNX bus can be accessed from any point on

the LAN. The IP address can be obtained by a DHCP server or by manual conguration. There are ve simultaneous connections

possible for access via KNXnet.

Figure 2. KNX 100G DIN Rail Installation

Installing Onto DIN Rail

1. Ensure the DIN rail is securely mounted onto the wall or furniture.

2. Place top rear against wall/furniture (Figure 2, 1).

3. Slide the unit down onto top of rail (Figure 2, 2).

4. Tilt the unit and snap onto the rail (Figure 2, 3).

Figure 1. KNX 100G Controls and Displays

DIN Rail

KNX 100G

Patent(s): www .extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

KNX 100G

KNX

Mode

P/Esc

Conn

e t

KNX 100G

Place top rear against

wall/furniture.

Slide down the unit

onto top of rail.

Tilt the unit an

snap into rail.

KNX 100G

Pat ent(s): w ww.extron.com/pa tents

33-2700-01 A

KNX 100G

at ent(s):

www.ext ron.com/patents

33-2700-01 A

KNX 100G

Patent(s): ww w.extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

KNX 100G

KNX

Mode

P/Esc

Conn

est

e t

LAN

33-2558-01 B

www.e xtron.com/pat ents

Bottom View

A KNX Bus connector

B Programming Mode Button

C Programming Mode LED (Red)

D KNX LED (multicolor)

E Mode LED (multicolor)

F IP LED (multicolor)

G Button Connection Up

H Button Connection Down

I Ethernet/LAN Connector

Figure 3. KNX 100G Application Diagram

LED Status Indicators

C Programming Mode LED

LED STATUS Meaning

LED lights red Programming mode is active

LED Off Programming mode is not active

E Mode LED

LED STATUS Meaning

LED lights green Device is working in standard operation mode

LED lights red Programming mode is active

LED ashes green 1x...5x Programming mode is not active

Manual operation is active

The selected tunnel (1-5) is not used and free

LED ashes orange 1x...5x Programming mode is not active

Manual operation is active

The selected tunnel (1-5) is used and free

LED ashes red Programming mode is not active

Manual operation is not active

The device is not properly loaded for example after an interrupted download

F IP LED

LED STATUS Meaning

LED lights green The device has an active Ethernet link and valid IP settings.

LED lights red The device has an active Ethernet link and invalid IP settings or not yet received the IP settings by a

DHCP server.

LED ashes green IP telegram trafc

D KNX LED

LED STATUS Meaning

LED lights green KNX 100G successfully powered

LED ashes green Telegram trafc on the KNX bus

LED lights red shortly Communication failure on the KNX bus

est

KNX 100G

Patent(s): www.extron.com/patents

33-2700-01 A

Prog. KNX

__.__.____

KNX 100G

KNX

Mode

P/Esc

Conn

Ethernet

Twisted Pair

Cable

IPC P PRO

550

LIMIT

2 3

4 5 6 7 8

RTS

CTS

COM

IR/S

IAL

REL

AYS

FLE

LIMI

OVE

eBU

ITC HED

12 V DC

100 0

LINK

ACT

5 6

Light

Shutters

Dimmer

Thermostat

(Temperature)

Dimme

Volum

KNX 100G

IPCP Pro 550

IPCP

Pro 550

TLP Pro 725M

Net work

IPCP PRO 550

OVER

LIMIT

4 5 6

RTS

COM

/SE

IAL

REL

AYS

FLEXI/O

LIMIT

eBU

WITCH E D

12 V

1000

LINK

5 6

TLP Pro 725M

KNX

Bus

KNX 100G Network Installation

1. Using a certied KNX twisted pair cable, connect to the

KNX BUS located on the top of the device (see gure 3).

2. Connect an ethernet cable between the Ethernet port

located at the bottom of the KNX 100G and the local

network.

3. Congure the KNX 100G using ETS.

4. Congure your Extron Control System using the Extron

driver targeted at your congured KNX 100G.

NOTE: Engineering Tool Software (ETS) is an application

for designing, commissioning, and debugging KNX

installations. Click this to view and purchase ETS link

for your KNX setup. KNX system setup should be done

by a certied KNX professional.

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	KNX 100G

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron KNX 100G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Extron Manualer

Extron HC 403 Manual

16 August 2025

Extron MLC 64 RS VC D Manual

5 August 2025

Extron MGP 641 xi 5K Manual

30 Juli 2025

Extron MLC 62 RS D Manual

30 Juli 2025

Extron DTP T UWP 4K 332 D Manual

22 Juli 2025

Extron DA HD 4K PLUS Manual

21 Juli 2025

Extron IN2004 Manual

21 Juli 2025

Extron FOX3 T 311 Manual

21 Juli 2025

Extron AAP 104 Manual

20 Juli 2025

Extron DTP T DSW 4K 233 Manual

20 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cres Cor H137WSUA5D Manual

20 August 2025

Moulinex Pulseo LM17GD Manual

20 August 2025

Tefal EasyGrill BG1303 Manual

20 August 2025

Tenda U2 Manual

20 August 2025

Tefal Ultraglide Plus FV5841 Manual

20 August 2025

Tefal I-Coach Touch QB950D Manual

20 August 2025

BEKO BDIN38551P Manual

20 August 2025

BEKO FSE52135DCRSN Manual

20 August 2025

Karma PRJ 5000 Manual

20 August 2025

Aqua-Vu Micro Stealth 4.3 Manual

20 August 2025