Extron PS 1220EB Manual

Extron Ikke kategoriseret PS 1220EB

Læs gratis den danske manual til Extron PS 1220EB (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Extron PS 1220EB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

About the Extron PS 1220EB Power Supply

The PS1220EB eBUS® Power Supply and Distribution Hub allows eBUS

endpoint devices such as EBP button panels to be powered separately in the

case when the IPCP Pro control processor does not provide enough power for

the desired quantity of eBUS devices.

Model Part

Number

Power Output Termination

PS 1220EB

70-988-01

24watts, 12VDC,

8A peak, 2A continuous; shared

between all outputs

Captive screw

ZipClip™ 200 101-001-01 — —

Features and Cabling

Features

Power

LED

ZipClip

Mounting Slot

(front and rear)

Notches for

Securing

Tie Wrap

Power

Input

DC Powered

eBUS Ports

eB US 2 4 WAT T S M AX

100 - 24 0V 50- 6 0H z

0.6 A M AX

–

Power and eBUS Input and Pass-through Connections

Extron STP20-2/1000 or STP20-2P/1000 cable is recommended for eBUS

connections.

e B U S 2 4 WA T T S M A X

100 - 240 V 50- 6 0Hz

0.6 A M AX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

eBUS® port

on an EBP

or other

eBUS

endpoint

device

V+

S G–

V C G

VOL

POWER

12V

1.0A MAX

GTx Rx

RTS CTS

CO M 1

31 2 4 G

D I G I TA L I / O

GTx Rx

CO M 2

-S+V +S G

e B U S

C1 2

R E L AY S

S G

I R / S

LAN

IPCP PRO 250

MAC: 00-05-A6-XX-XX-XX

S/N: ####### E######

I oPCP Pr

Tie drain wires to ground.

S+S+V

S+S

S+S+V

Ground

+ Signal

Signal

+12 VDC

Tie drain wires

to ground.

S+S+V

EBP

eBUS

Panel(s)

3/16" (5 mm) Max.

eBUS Connections

• Connect up to ve (5) eBUS endpoint devices

to the PS 1220EB.

• Wi the connectors the same at both ends.re

Power Input

Connect an IEC

power cord from

a 100-240 VAC,

50-60 Hz power

source he .re

PS 1220EB Rear Panel

ATTENTION:

Do NOT co ectnn

th toe po piwer n

an ce aty vide th is

al eadr y po d were

by the IPCP Pro

control processor

or by an additional

power supply.

Using the ZipClip 200

Attaching and Removing the Clip and Power Supply

To attach the power supply to the ZipClip 200 mounting clip:

1. Insert the bottom of the power supply down into the clip, starting with

one end.

2. Pivot the other end down and press until the clip snaps into place.

To remove the power supply from the ZipClip:

1. Press the tab on the ZipClip.

2. Pivot the power supply and lift it out of

the ZipClip.

Using Tie Wraps for Cable Strain Relief

1. Attach the power supply to the ZipClip 200 mounting clip as described

previously.

2. Fasten the power output cords to the ZipClip base.

a. Insert tie wraps (“zip ties”)

along the notches on

the side of the

power supply and

through the tie

wrap anchor points

on the ZipClip, then

around the cord.

b. Connect and pull

the tie wraps until

they are secure. Do not

over tighten.

Rack Mounting

Mounting to a Rack Shelf

These power supplies are one quarter rack wide. Up to four power supplies can

be mounted side by side directly onto a rack shelf.

1. Align the threaded holes in

the bottom of the

power supply

with the holes in

an Extron rack

shelf and fasten

the supply to

the shelf with

two 4-40 x

3/16" screws as

shown at right.

2. Bolt the rack

shelf to the

rack.

e BUS 24 WATTS MA X

100- 24 0V 50 -60 Hz

0.6A MAX

–

Tie Wrap

(2) 4-40 x 3/16"

Screws

RSB 123

Rack Shelf

On a Rack Shelf

Important Safety Instructions

This symbol is intended to alert the user of

important operating and maintenance (servicing)

instructions in the literature provided with the

equipment.

This symbol is intended to alert the user of the

presence of uninsulated dangerous voltage within

the product enclosure that may present a risk of

electric shock. On the product, risk of shock may

be indicated by this symbol.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this device apparatus during lightning storms or when unused

for long periods of time.

CAUTION: To reduce the risk of fire or electric

shock, do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases shall be placed

on the apparatus.

ATTENTION : Afin de réduire les risques d’incendie

ou de choc électrique, protégez cet appareil de la pluie ou

de l’humidité. Cet appareil doit être conservé à l’abri des

éclaboussures et des projections, et aucun objet contenant un

liquide, tel qu’un vase, ne doit être posé sur l’appareil.

Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as when

the power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

CAUTION: This apparatus is a Class I product. This

product must be connected to a mains socket outlet with a

protective earthing connection.

ATTENTION : Cet appareil est un produit de Classe1.

Ce produit doit être connecté à une prise femelle secteur

équipée d’une connexion de mise à la terre.

The mains plug is used as the disconnect device and shall remain

readily operable.

To prevent the risk of shock, do not attempt to service this equipment

yourself because opening or removing covers may expose you to

dangerous voltage or other hazards.

CAUTION:

Power sources — This equipment should be operated only from

the power source indicated on the product. This equipment

is intended to be used with a main power system with a

grounded (neutral) conductor. The third (grounding) pin is a

safety feature, do not attempt to bypass or disable it.

Power disconnection — To remove power from the equipment

safely, remove all power cords from the rear of the equipment,

or the desktop power module (if detachable), or from the

power source receptacle (wall plug).

ATTENTION :

Les sources d’alimentation — Ce matériel ne devrait être alimenté

qu’à partir de la source d’alimentation stipulée sur le produit.

Ce matériel est prévu pour être relié à un circuit d’alimentation

général doté d’un conducteur (neutre) mis à la terre. La

troisième broche (de terre) est un composant de sécurité.

N’essayez pas de l’éviter ou de la désactiver.

Déconnection de l’alimentation — Pour déconnecter le matériel

de sa source d’alimentation en toute sécurité, débranchez

tous les cordons d’alimentation de l’arrière du matériel ou

débranchez l’adaptateur secteur (si débranchable) ou de la

prise secteur (prise murale).

Mounting to Rack Rails Using a ZipClip

1. Fasten the ZipClip 200 mounting clip to a rack rail using two rack screws as

shown in the diagram below.

eBUS 2 4 WATTS M AX

100-

240V

50-60Hz

0.6A MAX

–

Inside

Rack

Side of Rack

ZipClip 200

Ba ofck

Rack

2. Insert the bottom of the power supply down into the clip, starting with one end.

3. Pivot the other end toward the clip and press until the clip snaps into place.

PS 1220EB • Installation Guide

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	PS 1220EB
Bredde:	109 mm
Dybde:	114 mm
Højde:	42 mm
Vægt:	400 g
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Pakkevægt:	2000 g
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	10 - 90 %
Driftstemperatur (T-T):	0 - 50 °C
Husmateriale:	Plast
Strømforsyningstype:	Indendørs
Udgangseffekt:	24 W
Certificering:	CCC, CE, C-tick, c-UL, CISPR 22 B, CISPR 24, FCC B, NEC 2, PSE, S-mark, UL
Udgangsspænding:	12 V
Udgangsstrøm:	2 A
Harmoniseret systemkode (HS):	85044090
Indgangsspænding:	100-240 V
Formål:	Universel
Indgangsfrekvens:	50-60 Hz
Justerbar udgangsspænding:	Ingen
AC udgange, antal:	1 AC stikkontakt(er)