Extron ShareLink Pro 2500 Manual

Extron Ikke kategoriseret ShareLink Pro 2500

Læs gratis den danske manual til Extron ShareLink Pro 2500 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Extron ShareLink Pro 2500, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
1
ShareLink Pro 2500 • Setup Guide
This guide provides instructions for installing and connecting the Extron ShareLink Pro 2500 4K wireless presentation system. The
ShareLink Pro 2500 allows anyone to present wireless or wired content from a personal device—such as a PC, laptop,
smartphone, or tablet—onto a display. It is compatible with Windows
® and macOS® computers, as well as AndroidTM and Apple®
iOS smartphones and tablets.
IMPORTANT NOTE:
Go to www.extron.com for the complete user guide, installation instructions, and specications
before connecting the product to the power source.
Installation
Mounting
The ShareLink Pro 2500 can be placed on a desktop or tabletop using the included rubber feet, or mounted to a rack or furniture
(see the , available at ShareLink Pro 2500 User Guide www.extron.com, for mounting options and instructions).
NOTE: Do not block or restrict air ventilation holes on the top and sides of the ShareLink Pro 2500.
Rear Panel Features and Cabling
RESET
POWER
--A MAX
12V
IN T O TPU UTPU
HD HD I/CMI M EC
1
HD I/CEM C
2
AUD I/IO COM I S DIG R/ O
L
LINE IN
RL
LINE OUT
R
LAN
A/PoE+ B
Tx Rx G 1 2 GS G
AA BB CC DD FF II JJGG HHEE
Figure 1. ShareLink Pro 2500 Rear Panel
A — Connect a power supply to this 2-pole captive screw connector.Power input
B — Connect an HDMI source device to this input.HDMI input
C — Connect HDMI displays to these female HDMI connectors. These independent HDMI outputs (primary and HDMI outputs
secondary) can be mirrored or matrixed (allowing different content to be routed to each output). Output 1 must be connected
to a display before Output 2 can be used. Output 2 can be disabled using Product Configuration Software (PCS) or SIS
commands.
D Audio input — Connect a microphone for ConferenceShare to this 5-pole, 3.5 mm captive screw connector. This input can
be mixed with the audio output signal using PCS or SIS commands. See Figure 2 for unbalanced or balanced input wiring.
E Audio output — Connect a balanced or unbalanced stereo (or dual mono) line level audio device to this 5-pole 3.5 mm
captive screw connector. Wire the connector as shown in figure 2:
ATTENTION:
• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–)
contacts.
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts
négatifs (–).
Balanced Input or Output Unbalanced Output
Do not tin the wire
s!
Left
Tip
Sleeve(s)
NO Ground Here
NO Ground Here
Tip Right
Tip
Sleeve(s)
Ring
Ring
Tip
Left
Right
Tip
Sleeve
Sleeve
Tip
Unbalanced Input
Left
Right
Figure 2. Audio Captive Screw Connector Wiring
F — Connect an RS-232 controllable device to this 3-pole captive screw connector (see the COM port ShareLink Pro 2500 User
Guide for details).
2
ShareLink Pro 2500 • Setup Guide (Continued)
G — Connect an IR or RS-232 source device to this 2-pole captive screw connector (see the IR/Serial port ShareLink Pro 2500
User Guide for details).
H — Connect devices such as switchers, sensors, LEDs, relays or other devices that accept a TTL signal. This port DIG I/O port
can be used to monitor or trigger events and fuctions (toggle digital output or issue commands) (see the ShareLink Pro 2500
User Guide for details).
I — Use this button to reset the device (see the for details).Reset button and LED ShareLink Pro 2500 User Guide
J — Use an Ethernet cable to connect a network switch, hub, router, or PC to these female RJ-45 ports. The LAN A LAN ports
port can also be used for Power over Ethernet (PoE+).
Default IP settings:
IP address: LAN A - 192.168.253.254, LAN B - 192.168.254.254 : LAN A - On, LAN B - Off DHCP
Gateway IP address: 0.0.0.0 Subnet mask: 255.255.255.0
DNS address: 0.0.0.0 Link speed and duplex level: autodetected
Front Panel Features and Cabling
ShareLink Pro 2500
I UTNPHDMI PUT OUT T IN PU
HD PASS
DECODER
SIGNAL
HDMI DECODER
USB
SS 5G
HDCPWINDOW PASS-THROUGH
HD WIN
STANDBY
SCREEN
CONFIG
900mA
1900mA
2
AA BB EE FFCC DD
Figure 3. ShareLink Pro 2500 Front Panel
A — Lights green when the unit is powered on.Power LED indicator
B — Connect a PC to this front panel USB-C connector to configure the ShareLink Pro. The port uses IP over Config USB port
USB technology. The IP address is always 203.0.113.22 and CANNOT be changed. This port is also discoverable via Extron
Toolbelt and Extron PCS software.
C — Use these buttons to select between HDMI window mode and pass-through mode. These HDMI input selection buttons
modes determine how the HDMI input is presented on the output (see below for details).
• HDMI Window button – Activates HDMI window mode, which displays the HDMI input source in addition to or
alongside any content currently being shared by client devices.
NOTE: Maximum input resolution for this mode is 4K @ 30 Hz.
• HDMI Pass-Through button – Activates HDMI pass-through mode, which routes the HDMI input signal directly
to the HDMI output unaltered. In this mode, neither the status bar nor decoder input streams are shown on
the output.
NOTE: Maximum input resolution for this mode is 4K @ 60 Hz.
D — Input LED indicators
• HDMI Signal LED – Lights green when an HDMI signal is detected.
• Decoder Signal LED – Lights green when one stream is detected. Flashes green when more than one stream
is detected at the same time.
• HDMI HDCP LED – Lights green when the source signal is encrypted. Turns off when input signal is not
encrypted or when HDCP authorization is disabled.
• Decoder HDCP LED – Lights green when the decoder source signal is encrypted. Turns off when decoder
source signal is not encrypted or when HDCP authorization is disabled.
E — Output LED indicators
• HD Win – Lights green when an HDMI source is active on the output in HDMI window mode. Lights amber if
HDMI pass-through mode is activated after originally being in window mode.
• Decoder – Lights green when at least one stream is active on the output. Lights amber if HDMI
pass-through mode is activated after at least one stream was active on the output.

Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: ShareLink Pro 2500

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron ShareLink Pro 2500 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Extron Manualer

Extron

Extron DTP3 IN2004 Manual

14 Juni 2025
Extron

Extron CPM 103 Manual

11 Marts 2025
Extron

Extron IN1608 XI Manual

10 Januar 2025
Extron

Extron ZipClip 100 Manual

3 Januar 2025
Extron

Extron HC 402 Manual

3 Januar 2025
Extron

Extron ShareLink Pro 2500 Manual

3 Januar 2025
Extron

Extron FOX3 SR 301 Manual

3 Januar 2025
Extron

Extron TMK 110 D Manual

3 Januar 2025
Extron

Extron SMB 210 Manual

3 Januar 2025
Extron

Extron FOX3 T 201 Manual

3 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Sony

Sony RM-V202T Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Attax Metroverb Manual

15 Juni 2025
Kohler

Kohler K-10124 Manual

15 Juni 2025
Planet Audio

Planet Audio P9900CPA Manual

15 Juni 2025
Levenhuk

Levenhuk LabZZ SP20 Manual

15 Juni 2025
Planet Audio

Planet Audio P62CP Manual

15 Juni 2025
Cranborne Audio

Cranborne Audio Carnaby 500 Manual

15 Juni 2025
Audio-Technica

Audio-Technica AT-VM740xML/H Manual

15 Juni 2025
Stamos

Stamos SWG-WC-3D Manual

15 Juni 2025
Planet Audio

Planet Audio P350MB Manual

15 Juni 2025