Extron UTM 100 Manual


Læs gratis den danske manual til Extron UTM 100 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Extron UTM 100, eller vil du spørge andre brugere om produktet?

Side 1/2
IMPORTANT:
Go to www.extron.com for the
complete user guide
, installation
instructions, and specifications.
UTM 100 and UTM 150 • Installation Guide
The Extron UTM 100 and UTM 150 under-table mounts accommodate 1U and 2U full rack
width products. Follow the steps below to assemble and install the UTM 100 and UTM 150
under a desk or table.
Installing the UTM 100 (Primary Mount) on the Product
Mounting the UTM 100 Assembly
Follow the steps below to attach the UTM 100 mounts to the primary product. Attach a UTM on
NOTE: Rack mounts or
rack shelf kits may be
purchased separately
for products that do
not have rack ears (see
www.extron.com
for models and part
numbers).
ATTENTION: Do not drill through the table or furniture. If the table is too thin or of
a different material for the supplied screws, use an appropriate type and length.
ATTENTION : Ne perçez pas à travers la table ou le meuble. Si la table est trop
ne ou faite dans un matériau différent de celui pour lequel les vis fournies sont
prévues, utilisez un type de matériau et une longueur appropriés.
Use the screws provided with the rack-mounted product to
attach the UTM 100.
1
2
Align the holes of the UTM 100 with the holes of the
rack ear, as shown at right.
Mounting
Hole
Hold the UTM 100 assembly under the desk or table at the
mounting location, and mark the locations of the four
mounting holes.
3
Drill a 3/32 inch (2.38 mm) diameter pilot hole at each of the four
marked locations.
4
UTM 100 and UTM 150 • Installation Guide (Continued)
68-2661-01
Rev. A
08 14
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
NOTE: If necessary for easier access, mark the location of the clearance opening,
then remove the UTM system to drill the hole.
6
Hook the UTM 100 assembly onto
the screws, as shown at right.
Slide the UTM assembly forward
or backward into either slot.
Tighten the screws to secure
the UTM assembly.
7
Drill a pilot hole through the clearance
opening on the UTM 100. Insert and
tighten a mounting screw (provided).
Insert a #8 x 1/2 inch mounting screw (provided) into
each of the four holes. Tighten each screw until it
protrudes 1/4 inch from the bottom of the table.
5
Clearance
Opening
Use the provided #10-32 Phillips head screws to add
one or mo UTM 150 brackets to the UTM systemre
(see image at right).
8
Mount products on the UTM 150 brackets, as shown
in steps 1 and 2 on the previous page.
9
Mounting the UTM 150


Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: UTM 100

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron UTM 100 stil et spørgsmål nedenfor, og andre brugere vil svare dig